Question about 1995 Isuzu Trooper

1 Answer

1995 isuzu trooper caliper removal

How do you remove front brake calipers from a 1995 isuzu trooper

Posted by on

  • Anonymous Mar 22, 2014

    seized rear brake caliper removal &repair Isuzu 3.1td

  • Anonymous Mar 30, 2014

    replace front crankshaft oil seal



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Isuzu Master
  • 22,306 Answers

Remove front wheel ,look at back of caliper and and look for teh two retaining bolts that hold the caliper to the support bracket.if not sure take it to a garage as any mistake could kill someone

Posted on Nov 15, 2008



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do u remove hubs on a 1992 Isuzu big horn

TO DO WHAT? not even the smallest hint on job or failure.>?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....

Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... ( covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

How to replace front brake pads on a 1995 Isuzu Trooper

remove the bolts. if you need to ask this you should not do brakes.
pins or bolts. the below is trooper and is like all cars, just about. shows it as does the real FSM (fact.serv. man)
since this is safety issues, ill pop it up

  • Use a turkey baster or other suitable device to remove the brake fluid from the master cylinder reservoir. Discard of the brake fluid properly. Do not reuse old brake fluid.
  • Raise and safely support the vehicle on jackstands.
  • Remove the wheel and tire assemblies.
  • If the brake pads are being replaced (and the caliper is NOT being overhauled), install a C-clamp on the caliper with the solid frame side of the clamp rests against the back of the caliper and the driving screw end rests against the metal part (center backing plate) of the outboard pad. Tighten the clamp until the caliper moves sufficiently to bottom the piston in the bore, then remove the clamp.
  • Remove the caliper mounting bolts from the back of the caliper. If the caliper is not being completely removed from the vehicle, detach it from the mounting bracket and support it using a coat hanger or length of wire. DO NOT allow the hose to be stretched, twisted, kinked or otherwise damaged.
  • If the caliper is being completely removed from the vehicle, place a drip pan below the caliper and disconnect the flexible brake hose-to-caliper banjo-bolt. Discard the pressure fitting washers, then remove the brake caliper from the vehicle and place it on a clean work surface.
  • To inspect the caliper assembly, perform the following procedures:
    • Check the inside of the caliper assembly for pitting or scoring. If heavy scoring or pitting is present, caliper replacement is recommended.
    • Check the mounting bolts and sleeves for signs of corrosion; if necessary, replace the bolts.
  • warning
  • If the mounting bolts have signs of corrosion, DO NOT attempt to polish away the corrosion. Instead the bolts must be replaced to assure proper caliper sliding and prevent the possibility of brake drag or locking.
  • warning 2, do not fail to inspect rotors for CRACKS.
  • end tip of IceBerg.

Jul 05, 2014 | 1995 Isuzu Trooper

1 Answer

2000 isuzu trooper brakes? dont always release after stop

brake caliper sliders or pistons seized. (most common problem)

Mar 14, 2013 | 2000 Isuzu Trooper

1 Answer

Change front rotors ......99 rodeo 2WD

It is VERY simple:

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove 1/2 of the volume of brake fluid from the master cylinder to prevent overflow when the caliper piston is compressed.
  3. Raise and safely support the vehicle.
  4. Remove the wheel and tire assemblies.
  5. Remove the brake caliper without disconnecting the brake line. Support the caliper with a length of wire. Do not let the caliper hang from the brake hose.
Remove the brake caliper mounting bolt and guide bolt and remove the caliper from the mount. The brackets can be removed for additional work space.


  1. Unbolt the caliper and suspend it with a piece of wire. Do NOT let the caliper hang by the brake hose.
  2. Remove the rotor.
  3. Installation is the reverse of the removal procedure.b8b7b9d.gif

Aug 07, 2010 | 1999 Isuzu Rodeo

1 Answer

Servicing front hubs

Automatic Locking Hub

  1. Shift transfer lever to the ``2H'' position, then move vehicle forward and rearward approximately three feet.
  2. Raise and support vehicle, then remove wheel and tire assemblies.
  3. Disconnect brake hose from caliper.
  4. Remove caliper locking bolt.
  5. Rotate pad assembly upward then remove pad retaining clip and caliper assembly
  6. Remove brake pad support bracket.
  7. Remove hub cap retaining bolts, then the hub cap, Fig. 15.
  8. Remove housing assembly, snap ring and shims.
  9. Remove drive clutch assembly, inner cam and lock washer.
  10. Using tool J-36827 or equivalent, remove hub nut.
  11. Remove hub and disc assembly.Manual Locking Hub

    1. Shift transfer lever to the ``2H'' position and set free wheeling hub into Free position.
    2. Raise and support vehicle, then remove wheel and tire assemblies.
    3. Disconnect brake hose from caliper.
    4. Remove caliper locking bolt.
    5. Rotate pad assembly upward then remove pad retaining clip and caliper assembly
    6. Remove brake pad support bracket.
    7. Remove housing assembly retaining bolts then the housing assembly Fig. 16.
    8. Remove snap ring and shims.
    9. Remove body assembly and lock washer.
    10. Using tool J-36827 or equivalent, remove hub nut.
    11. Remove hub and disc assembly

Jul 02, 2010 | 1991 Isuzu Trooper

1 Answer

How to collapse rear calipers

if it has ratcheting calipers , you will need to clamp off brake line , open bleeder and turn in the piston counter clockwise with proper tool to get it back in , will need to bleed when done

Jun 27, 2010 | 1991 Isuzu Trooper

1 Answer

95 isuzu troper 4x4 front break rotors or bad how do you take them off

1. jack up vechicle, support by jack stands
2. remove tire
3. remove bolts holding caliper
4. remove 2 bolts holding caliper bracket to spindle
5. slide rotor off
6. repeat in reverse order

Feb 05, 2010 | 1999 Isuzu Trooper

1 Answer

Front brake service for a 1995 subaru legacy. Repair calipers and new pads how to do it?

Calipers need repairing only if they leak. Remove tire then calipers. Remove brake pad from calipers. Compress pistons in brake caliper and install new brake pad. Replace calipers and tire.

Jul 29, 2009 | 1995 Subaru Legacy

1 Answer

Brake job on 1994 isuzu trooper

are they drums on the rear? if not you can do this. on the caliper there should be 2 bolts holding it on. loosen one and pull the other out. lift the caliper up or down remove pads open the master cylinder so that you can compres the piston on the caliper. if you dont open the master sylinder cap it will be very tough. replace pads. tighten bolts nice and snug. then with car off pump brakes till tough. make sure you fill the master sylinder up that way no air gets in to it. if you do you gonna have to bleed the brakes. if that happens start at the passenger side rear then driver side rear then passenger front then driver front. please lemme know if you need help or if i helpd at all

Apr 24, 2009 | 1994 Isuzu Trooper

Not finding what you are looking for?
1995 Isuzu Trooper Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides