Question about 1990 Volvo 740

1 Answer

Signal light just need to replace it and don't have instructions on installing it

Posted by on

  • d Gring May 11, 2010

    which light?
    front or back?


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

The front is quite easy. For the lens removal; there are two tabs, top and bottom, pinch them together and pull it out. Just push back in when finished. For the bulb; grab the wire leading to it at the end, and turn it counter-clockwise then pull it out.

Rear is tricky on the wagon, I don't know about the sedan, but I bet it isn't difficult. Very few things on these cars are.

Posted on Oct 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Dodge Ram 3500: brake lights don't come on, switch has been replaced and installed to instructions, turn, four ways, parking lights and cruise control interrupt all work. Is there a brake rel


have you checked wire harness @ rear of truck ? and along frame rail, ? and condition of the rear taillight assymblies, ? corrosion could be in these areas. check all ground wires also, not sure about relay ! don' t think so ! why would brakes need one ?

Feb 02, 2013 | Dodge Ram 250 Cars & Trucks

1 Answer

1995 GMC Suburban XLT 4x4 SLT. the top break light works but not the sides. Also the turn signals are not working. Have checked fuses and changes bulbs..What can this be


Turn signals are one of the easiest systems in your car to troubleshoot. Your signal flashers either work or they don't. If they don't, either you need to change the bulbs or you need to replace your turn signal relay. Know more about car diagnostic tools for automobile.

Oct 29, 2012 | Cars & Trucks

1 Answer

Brake lights won't work.... replaced fuse it's fine, top light on hatch works, but right and left don't


need to check the multi-function switch. the brake light signal goes through the turn signal switch on the steering column. the brake lights come on if the turn signal is not being operated. the circuit for the brake light can loose contact in the switch.

Aug 12, 2011 | 2007 Chevrolet Tahoe

1 Answer

Signal lights don't work


check your fuse box for fuse burnt out, but most likely your signal light flasher switch is out, and needs replacing. Check your manual it will tell you where your signal flasher is located, it is a real easy part switch and not very much $ for just a flasher, normally under 20 bucks at auto parts stores. let me know if this helped you. Thanks Mikemc1bean_13.jpg

Jun 22, 2011 | 2006 Chevrolet Silverado

2 Answers

When signal light is on, there is no clicking noise.


are the signal lights working if so don`t worry about it as sometimes the manufacture has tried to make the interior so quiet sometimes you don`t hear anything.

Jun 16, 2011 | 2008 Chevrolet Impala

1 Answer

How to fix turn signal on 86 Chevy Astro Van


you don`t say but do the lights work either on the front/back on both sides.if not then it may be a fuse that needs replacing or need a bulb replacement.if the lights work but don`t flash then it sounds like a signal flasher problem.the flasher is located in the fuse panel under the dash on the drivers side.if the hazard flashers work then turn them on to find the hazard flasher by the fuse panel then you will know what the signal flasher looks like and change the signal flasher.make sure you change the one for the signals and not the hazard one.if the hazards work then i would say the signal switch is good as the hazards work through the same switch.

Apr 21, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

I just bought a 2009 dodge ram without fog lights i bought a bumper with fog light an switch them out but i need to know how to connect the lights to the factory switch inside what do i need to do


If your PU didn't come with factory installed fog lights then you will need to replace your headlight switch with a fog light enabled headlight switch.

Here is a link to the factory dealer-installed instructions.....

http://www.mopardodge.com/accessories/Instructions/82208102AC_IFU.pdf

You only need to get the components you don't already have. The headlight switch that is fog enabled will pull out for fog light operation, if yous doesn't you need to replace the switch and do some wiring as shown in the pdf file linked above.

Hope this helps!

Mike

Apr 18, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

Turn signal dosent work


you need to check to see which bulbs don`t work both front and back lights for the signal on the side it`s not working,you don`t say if any signals work or not if no signals work then you need to check the fuses under the dash on the driver`s side.now if it`s just one side then check the lights as mentioned above.if one isn`t then replace the bulb.if neither bulb is working then it sounds like the signal flasher is not working.turn on the hazard flashers and check the lights front and back.if all bulbs work then leave the hazards on and look under the dash for the flasher that is making the noise,this will show what the signal flasher will look like,then find the signal flasher on the fuse panel under the dash it should be located on the fuse panel.and replace

Mar 15, 2011 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Need to remove the passenger side headlight assembly on an "06 vw touareg?


There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.

To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).
Hope this helps!

Mar 10, 2009 | 2006 Volkswagen Touareg

Not finding what you are looking for?
1990 Volvo 740 Logo

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...