Question about 2001 Honda Civic

1 Answer

How to install rear bumperr

Some one hit my car from back and i have crack in my bumper and my trunk i messed up too. trunk floor got squeese and have some holes too. can you tell me how to replace rear bumper and how to fix trunk floor. thank you

Posted by on

  • salman1981 Sep 01, 2008

    but my trunk is in really bad condation. trunk is not flat any more its more like water waves. is there any way i can fix that or can i buy new trunk and how much it will cost me

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 421 Answers

There are two ten mm bolts that hold up the two corners of the bumper followed by a dozen or so push pin type plastic clips remove the two tens and pull the centers out of all the plastic clips and remove the lower halves, the bumper then has a plastic bracket on each side that if pulled straight back will slide right off, as for the sheet metal reapir you can either buy a cheap bodymans slide hammer and drill and pull where it needs or if there is damage to the bumper rebar ( metal bar under cover) you can get a ratcheting "come along" and set the ebrake and chain the other end to a tree, and pull it that way .sounds like you may even be able to use a big sledge hammer and knock the trunck back out also -jeff

Posted on Aug 31, 2008

  • jeff r
    jeff r Sep 01, 2008

    if the trunk is that bad i would bring it to a body shop and have them put it on a frame machine and straighten out the trunk for you or they could install a new trunk pan but that's all very involved for someone with little or no collision repair experiance you could also consider putting it thru your insurance if you have that type or coverage a $500 deductible is allot cheaper than a few thousand in repair bills please rate -jeff

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the rear bumper cover on a pontiac 2004 grand prix


  1. Open the trunk.
  2. Remove the rear compartment sill plate. (Trim round the back edge of the trunk)
  3. Pull the left and right compartment side trim panels down to access the fascia bolts and nuts.
  4. Remove the tail lamps.
  5. Remove the fascia bolts and nuts from the rear bumper fascia 1 nut 1 bolt on each side near tail lights.
  6. Remove the push-in retainers from the top edge of the fascia.(4 plastic circles, pull up on center of cirle with screwdriver
  7. Raise and support the vehicle.
  8. From underneath Remove the push-in retainers from the rear bumper fascia (one on each side I think)
  9. Remove the fascia bolts from the rear bumper fascia. on on each side from, up where the facia connects to the quater panel)
  10. Remove the rear bumper fascia from the vehicle

Apr 14, 2011 | 2004 Pontiac Grand Prix

1 Answer

Can you bye a rear frame for a 1998 sunfire were the rear end goes


YOU CAR DONT HAVE FRAME YOU HAVE A UNIBODY.UNIBODY IF REAR OF CAR BEEN DAMAGED.THEN THE REAR FENDERS AND QUARTER PANELS HAS TO CUT OUT AND WELDED IN PLACE ALSO THE TRUNK FLOOR PAN HAS TO BECUT OUT AND WELDED BACK IN PLACE .THE TRUNK LID HAS TO BE REMOVED ALSO THE BUMPER HAS TO BE REMOVED.BASICALLY BY CAR BEEN A UNIBODY THE REAR PART OF THE CAR HAS TO BE CUT OUT NEW BODY PARTS WELDED BACK IN PLACE.THIS JOB FOR BODY SHOP.YOU NEED LOTS OF TOOLS AIR CHISELS MIG WELDER, GAS WELDER,BODY JACKS ,HYDRALIC UNIBODY FRAME STRAIGHTNERS.

Mar 24, 2011 | 1998 Pontiac Sunfire

1 Answer

How to remove rear bumper for my 95 honda accord


Under the rear wheel wells, along the edge near the back is a screw. There is one on mine but there be more than one. Remove the screws for each.

After this, pop the rear trunk and look along the edge of the trunk right where the trunk hood meets the trunk itself. There are three black plastic screws that hold the rest of the rear bumper to the frame. I don't know exactly how these screws work but they don't just unscrew - I had to pop them out with a screw driver instead of rotating them out. Once those are out the rear bumper will lift up and off. There are some hooks along the rear wheel well where you removed the screws - you need to lift and pull out these edges, then lift the entire rear bumper off from the middle of the rear bumper.

Once you've done this, it goes pretty easily. If you have no problem with removing the black plastic screws or unhooking the edges, it should come off in less than five minutes.



Read more: http://wiki.answers.com/Q/How_do_you_remove_1996_Honda_Accord_rear_bumper#ixzz1Azw2wVAN

Jan 14, 2011 | 1995 Honda Accord

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

2 Answers

How do you remove a rear bumper


How To Install Replace Remove Rear Bumper Cover Honda Civic 01-05

Dec 11, 2010 | 2004 Honda Civic

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

Emergency Trunk Release Boxster 2000


the release cable is behind the rear bumper on the nearside below the tail lamp. if you remove the inner arch liner and heatshield for exhaust enough to get your hand up there to reach and pull wire as you cant remove bumper without openingthe boot.

Jul 31, 2009 | 2002 Porsche Boxster

2 Answers

Lexus ES300 trunk leaks when it rains


This may sound odd but if you can put a small person in the trunk with a flashlight while you pour water in the areas suspected, they can trace the leaking area, believe it or not I used to use this method while I was a Ford mechanic. Otherwise, maybe you can apply clear or black silicone to the area or remove the screw or bolt and coat it with silicone and replace it.

Apr 04, 2009 | 2000 Lexus ES 300

1 Answer

Replacement of rear outside tail light assembly


If you're asking how do you change a taillight bulb, then follow this procedure:

Open the trunk lid.

Disconnect the connectors from the taillights (taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps.) There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in.


Brake Lights/Taillights: 21/5 W

Rear Turn Signal Light: 21 W

Back-up Light: 21 W

Rear Side Marker Light: 5 W


Turn the bulb sockets 45 º counterclockwise to remove the bulbs.


If you're removing the taillamps with the bumper off there are 3 nuts and screws that hold the taillight to the rear panel of the car that have to come off from the inside of the trunk.
Remove the nuts and screws, then remove the taillight.

hope that answers your question

Aug 15, 2008 | 2006 Volkswagen Jetta

Not finding what you are looking for?
2001 Honda Civic Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...