Question about 2006 Toyota Corolla

1 Answer

Brake Repair How do I remove the rotors? I removed the clip that holds the disc pads against the rotor, but can't get the rotor off.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

You also have to remove the bracket that hols the caliper to the rotor. hope this helps. they will most like be an 18mm head for the bolts that hold the bracket. hope this helps.......please rate this

Posted on Aug 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i change the brake pads on the rear tires??


Hi. Please see procedure below:

Remove the old Brake Pads

1 Park your car on a level surface. If you have a stick shift car make sure the car is in gear. Place blocks in front of the front tires so the car does not move while you are working on it.

2 Open the hood of your car and locate the master cylinder. If necessary, remove brake fluid until the level in the container is less than half full. A turkey baster is a good tool for this. Put the brake fluid in the plastic container and dispose of it the way you dispose of motor oil.

3 Raise the rear end of your car with your car jack. Remove the rear tire or wheel assembly.

4 Remove the parking brake cable from the back of the caliper. Use the pliers to remove the cable clip (restraining clip). This step is done only for Grand Prix RPO Z7Us.

5 Hand-tighten two lug nuts to the studs to hold the disc rotor in place while you work on the caliper. Remove the bolt and washer holding the cable support bracket to the caliper. The cable support has the parking brake cable and brake hose attached to it. This step is not done for Grand Prix RPO Z7Us.

6 Use the socket wrench to remove the caliper guide pin bolts. Slide the caliper off of the disc rotor and hang it in the wheel well with a small bungee cord or wire hanger; Don't let the caliper hang from the brake hose.

7 Remove the brake pads and shims from the caliper. Throw away the shims.

Install the new Brake Pads

1 Use the spanner tool to rotate the piston clockwise all the way into the caliper. Make sure the notches on the piston are at the 6 and 12 o'clock positions. There is a boot (rubber seal) around the piston bore. Lift the seal's inner edge and press out any trapped air. Insert the brake pad clips into the caliper support.

2 Apply a thin coat of lubricant to the parts of the inner pad that come in contact with the caliper piston and mounting areas. As you install the brake pads in the caliper support, make sure the wear sensors are downward and at the leading edge of the rotor when the tire rotates. Push the brake pads into the support, holding the metal shoe edge against the spring end of the pad clips. This slightly bends the spring ends and lets the notches engage with the support. This step does not apply for the Grand Prix RPO Z7U.

3 Swing the caliper back into place over the brake pads and replace the mounting bolt. Reconnect the cable support bracket and tighten the bolt to 32-ft.lb. (43 Nm). Remove the lug nuts holding the rotor in place. For the Grand Prix RPO Z7U, Slide the caliper back into place on the disc rotor. Reconnect the parking brake cable. Insert and tighten the caliper mounting bolts to 44 foot lb. (60 Nm).

4 Replace the tire wheel assembly. Lower the car to the ground.

5 Pump the brake pedal a few times to seat the brake pads. Do this before trying to move your car.

6 Add fluid to the master cylinder container to replace any you removed before you removed the old brake pads.

7 Season the brake pads by making only gentle stops when you are driving for the first week

Thanks!

Apr 29, 2011 | 2006 Pontiac Grand Prix

1 Answer

Need instructions to remove the front rotor on F250 Four wheel drive truck - 2001 year


  1. Raise and support the vehicle; Remove the wheel and tire assembly;
  2. After removing the tire, remove the brake pads;
  3. Remove the disc brake caliper by removing the two disc brake caliper pin bolts. Lift the disc brake caliper from the disc brake caliper anchor plate (2B292). If necessary, remove the V-springs.
  4. Remove the pads. Remove the front disc brake caliper anchor plate stainless steel rail clips.
  5. Remove the rotor.
  6. Note: Perform this step for DRW vehicles. Remove the eight hub extender nuts, the hub plate and the rotor. Remove the eight hub plate nuts. Remove the hub plate. Remove the rotor.

Mar 02, 2011 | 2001 Ford F250 Super Duty Super Cab

1 Answer

I need to know how to change the front brakes on a 94 jeep grand cherokee laredo.


  1. Raise and support the vehicle safely using jackstands. Remove the wheel(s) on the side to be worked on.

NOTE: Removing a small amount of brake fluid from the master cylinder using a turkey baster


zjlimited_10.jpg

Fig. 4: Tighten the C-clamp until the piston reaches the bottom of its bore


zjlimited_11.jpg

Fig. 5: Remove the caliper mounting bolts


zjlimited_12.jpg

Fig. 6: Slide the caliper off the brake rotor

  1. Drain a small amount of the brake fluid from the front reservoir using a suction gun or a turkey baster.
  2. Place a C-clamp on the caliper so that the solid end contacts the back of the caliper and the screw end contacts the metal part of the outboard brake pad.
  3. Tighten the clamp until the caliper moves far enough to force the piston to the bottom of the piston bore. This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly
zjlimited_13.jpg

Fig. 7: Support the caliper so that no tension is placed on the brake hose


zjlimited_14.jpg

Fig. 8: Hold the anti-rattle clip while removing the outboard pad (4)


zjlimited_15.jpg

Fig. 9: Removing the outboard brake pad


zjlimited_16.jpg

Fig. 10: Remove the inboard pad and anti-rattle clip


zjlimited_17.jpg

Fig. 11: Removing the inboard brake pad


zjlimited_18.jpg

Fig. 12: Removing the anti-rattle clip

  1. Remove the C-clamp.
Do not push down on the brake pedal or the piston and brake pads will return to their original positions up against the rotor.
  1. Remove the caliper mounting bolts. Tilt the top of the caliper outward and lift it off the rotor.
  2. Hold the anti-rattle clip against the caliper anchor plate and remove the outboard brake pad.
  3. Remove the inboard pad and the anti-rattle clip. Be sure that the support spring is removed with the inboard pad.
zjlimited_19.jpg

Fig. 13: Install the support spring onto the shoe of the inboard brake pad


zjlimited_20.jpg

Fig. 14: Installing the inboard pad


zjlimited_21.jpg

Fig. 15: Piston extension on new and worn brake pads

  1. Use a piece of wire to support the caliper so that no tension is placed on the brake hose. Do not allow the caliper to hang by the brake hose.
To install:
  1. Clean all the mounting holes and bushing grooves in the caliper ears. Clean the mounting bolts. Replace the bolts if they are corroded or if the threads are damaged. Wipe the inside of the caliper clean, including the exterior of the dust boot. Inspect the dust boot for cuts or cracks and for proper seating in the piston bore. If evidence of fluid leakage is noted, the caliper should be rebuilt.
Do not use abrasives on the bolts in order not to destroy their protective plating. You should not use compressed air to clean the inside of the caliper, as it may unseat the dust boot seal.
  1. If not already in place, attach the support spring to the inboard brake pad.
  2. Install the anti-rattle clip on the trailing end of the inboard pad's anchor plate. The split end of the clip must face away from the rotor.
  3. Install the inboard pad in the caliper. The pad must lay flat against the piston.
  4. Install the outboard pad in the caliper while holding the anti-rattle clip.
  5. With the pads installed, position the caliper over the rotor.
Before securing the caliper, ensure the brake hose is not twisted, kinked or touching any chassis parts.
  1. Lubricate the caliper pins and bushings with silicone grease. Line up the mounting holes in the caliper and the support bracket and insert the mounting bolts. Make sure that the bolts pass under the retaining ears on the inboard shoes. Push the bolts through until they engage the holes of the outboard pad and caliper ears. Thread the bolts into the support bracket and tighten them to 7-15 ft. lbs. (9-20 Nm).
CAUTION On models with manual/power brakes, pump the pedal until the caliper pistons and brake shoes are seated. On models with anti-lock brakes, turn the ignition ON and allow the booster pump to build pressure. Pump the brake pedal until the shoes are seated and the indicator lights turn off.
  1. Fill the master cylinder with brake fluid and pump the brake pedal to seat the pads.
  2. Install the wheel assembly and lower the vehicle. Check the level of the brake fluid in the master cylinder and fill as necessary.

Remember to rate this, good luck.

Nov 04, 2010 | 1994 Jeep Grand Cherokee

1 Answer

How do you replace the front and rear brakes in a 2003 pontiac Grand Prix


Removal & Installation Front To Remove:
  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the bottom brake caliper pin bolt.
  5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
  6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket gmpc_l4.gif

  7. Remove the inboard and outboard brake pads from the brake caliper bracket.
To Install:
  1. Install the brake pad retainers and both brake pads into the caliper bracket.
  2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
  3. Reinstall the tire and wheel assembly.
  4. Lower the vehicle.
  5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  6. Check the master cylinder level and add fluid as necessary.
Rear To Remove:
Rear disc pads R&I gm-09-00-492.gif

  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the upper caliper mounting bolt.
  5. Pivot the caliper down to access the pads.
  6. Remove the inboard and outboard pads from the caliper bracket.
  7. Remove the brake pad clips from the caliper bracket.
  8. Compress the piston back into the bore using a C-clamp and the old inner pad.
To Install:
  1. Install new brake clips in the caliper bracket.
  2. Install the inboard and outboard pads in the caliper bracket.
  3. Pivot the caliper up over the pads.
  4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
  5. Remove the 2 wheel nuts securing the rotor.
  6. Reinstall the tire and wheel assembly.
  7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  8. Check the master cylinder level and add fluid as necessary.
prev.gif next.gif

Aug 26, 2010 | 2003 Pontiac Grand Prix

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

Need help changing brake pads and routers on 2003


Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
  1. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    For the rotors:

    1. Remove brake fluid from the master cylinder brake fluid reservoir until the reservoir is approximately 1/2 full. Discard the removed fluid.
    2. Raise and safely support the front of the vehicle. Remove the front wheels.
    1. Remove or disconnect the following:
    2. Front brake caliper guide pin bolts
    • Brake caliper by slowly sliding it up and off the adapter and brake rotor. Support the caliper out of the way with a strong piece of wire. Do not let the caliper hang by the brake hose or damage to the brake hose will result.
    1. If necessary, compress the caliper piston into the bore using a C-clamp. Insert a suitable piece of wood between the C-clamp and caliper piston to protect the piston.
    2. Outboard disc brake pad from the caliper by prying the brake pad retaining clip over the raised area on the caliper. Slide the brake pad down and off the caliper.
    • Inboard disc brake pad from the caliper by pulling the brake pad away from the caliper piston until the retaining clip on the pad is free from the caliper piston cavity
  • To install:
    1. Be sure the caliper piston has been completely retracted into the piston bore of the caliper assembly. This is required when installing the brake caliper equipped with new brake pads.
    2. If equipped, remove the protective paper from the noise suppression gaskets on the new disc brake pads.
    3. Install or connect the following:
      • New inboard disc brake pad into the caliper piston by pressing the pad firmly into the cavity of the caliper piston. Be sure the new inboard brake pad is seated squarely against the face of the brake caliper piston.
      • Outboard disc brake pad by sliding it onto the caliper assembly
      • Brake caliper assembly over the brake rotor and onto the steering knuckle adapter
      • Caliper guide pin bolts and torque to: 35 ft. lbs. (47 Nm) on 2002–04 models or 26 ft. lbs. (35 Nm) on 2005 models
      • Front. Apply the brake pedal several times until a firm pedal is obtained.
    4. Check the fluid level in the master cylinder and add fluid as necessary. Road-test the vehicle.

    May 28, 2010 | 2003 Chrysler Town & Country

    1 Answer

    Brake rotors need to be resurfaced,explain best way to remove rotors from vehicle.


    front ones remove wire clip remove bolts from caliper hang caliper out of way remove pads remove 2 bolts from pad carrier put to one side remove 2 disc retaining bolts remove disc may need hammer clean hub flange with wire brush fit new disc clean pad carrier and refit fit new pads put some copper grease on back of pads push in caliper piston slowly using large grips or g clamp fit and secure caliper pump up brake pedal check brake fluid level do other side for rear brakes see my solutions

    Dec 01, 2009 | 1999 Volvo S80

    3 Answers

    How to replace brake pads and rotors


    It is pretty straight forward. The Ranger has front disc brakes.
    If possible spray everything with brake cleaner to reduce asbestos dust as you work on the brakes. Best not to breathe in any of the nasty debris on the brakes and caliper. If I have them I wear nitril gloves for less mess on the hands.
    Take the wheel off. The caliper holds the brake pads. On mine it is a large allen bolt at the inside of the caliper to take it off. You don't have to remove both allen bolts--take off one and then loosen the other. THer caliper can then be rotated off the rotor. Now you can remove the rotor--it may have a screw holding it on still--remove that and pull it off the wheel hub.(Sometimes they can be stuck on, but they pretty much are just hanging onto the wheel hub studs) Do one at a time and then if you have any issues, look at the other one. The brake pads themselves kind of snap into place in the caliper. Remove the old ones noting any orientation issues and any shims--some of them come with thin plate shims that fit behind them. When you are ready to replace the pads, you need to use a clamp to drive the caliper piston back so that the pads on the cliper will fit onto the new rotor when they are rotated back. Make sure the bolts on the caliper are tight.
    There rear are less essential since most of the stopping is from the front--let me know if this helps to push my rating up.

    Mar 27, 2009 | 1999 Ford Ranger SuperCab

    2 Answers

    NEED TO REMOVE REAR ROTOR


    Take off the wheel, remove the brake caliper (2 bolts on the back), then the rotor just slides off, the wheel studs are part of the hub assembly not the rotor.

    Nov 21, 2008 | Hyundai Motor 2002 Sonata

    Not finding what you are looking for?
    2006 Toyota Corolla Logo

    Related Topics:

    86 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...