Question about 2002 Chrysler 300M

1 Answer

Tire pressure monitor relearn

How do you do a tire pressure sensor relearn on a 2002 300M

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

That can only be done through the ecm(engine control module) main computer. you have to take it to a shop and have them reprogram the perameters with a scan tool. take it to a small shop it will be cheaper than going to a dealer. hope this helps......please rate this......thanks

Posted on Aug 31, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The tire light flashes then stays on 2011 Dodge Grand Caravan What could that mean?

Diane, it is sensing low air pressure in one of the tires, or faulty sensor. check air pressure in tire and fill to specification.
Check the attached links for more info,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Why Is My TPMS Light Flashing It Could Be Time for New Sensor Kal Tire

Dodge Chrysler Jeep Fiat TPMS Tire Pressure Monitoring System Relearn...

Tire Pressure Warning Light

Mar 12, 2016 | 2011 Dodge Grand Caravan

2 Answers

I purchased a 2004 GMC Yukon Feb 7th, and the "service tire monitor" light on the DIC has always been on. What is the problem with it and can it be fixed?

This light comes on when tire pressure is low. Each wheel has individual sensors to monitor tire pressure. You have an issue with one or more of the wheels/sensors. Take it to a reputable repair shop and have the system tested. You may have one or more bad sensors or the vehicle may not have any sensors equipped if the original rims are not installed when you purchased it..

May 15, 2015 | GMC Cars & Trucks

2 Answers

How to repair tire pressure sensor monitor

Replace it

It is inside the tire

It is the tire stem & sensor assy

Sep 08, 2014 | Cars & Trucks

1 Answer

How to reset tire pressure monitor for 2010 chevy equinox

There are two different ways to relearn your Tire Pressure Monitoring System (TPMS). One is with a TPMS scan tool (this is the preferred method) and the other is the manual method (pain in the "you-know what", but requires no special tools or equipment).

To use the manual method, set the parking brake. Enter into TPMS RELEARN using the Driver Information Center (DIC) controls. (SEE Owner's Manual)

When you have successfully entered TPMS RELEARN, the horn will chirp and the left front turn signal will illuminate. Increase or decrease the tire inflation pressure on the left front tire for 8 to 10 seconds. The horn will "chirp", indicating that the left front tire pressure sensor has been relearned and the turn signal at the right front will illuminate. Repeat the process for the right front tire. The horn will chirp and the right rear turn signal will illuminate indicating that the right front tire has been relearned and now you must now repeat the process at the right rear tire. Then you will have to repeat this a fourth time at the left rear. When the left rear tire has been relearned, the horn will sound a "double chirp" indicating that the relearn process has successfully completed.
At this time, turn the ignition switch to the OFF position and adjust all of the tire pressures to the specification printed on the tire certification label inside the drivers door/door pillar area.

Mar 21, 2012 | 2010 Chevrolet Equinox

1 Answer

If I take out the tire pressure sensors from my wheels would the tpm warning go off from my dashboard?

No.Because the tire pressure monitor is looking for a frequency from the sensors and does not see it.There for the light will stay on constantly.If you have a light that is constantly on and the tire pressures are all fine.Then you need to relearn the tire pressure monitor to make the light go off.Unless you have a bad sensor.There is a special tool for relearning the tire pressure monitor.It also has to be put in learn mode to perform this.Which is done with your keyless entry fob or in your case you apply the parking brake turn the key on and turn the light switch from off to park 4 times within 4 seconds.The horn will chirp twice.this means the system is in learn mode.This is where the special tool comes need to go to a repair shop that has a tool for relearning.If the sensors are all good the light will go off.Hope this has helped.Good luck.

Dec 12, 2011 | 2007 Chevrolet Colorado (Extended Cab) New...

2 Answers

2010 Chevrolet Camaro... My TPMS (Tire Pressure Monitoring Sensor) light came on blinking and car is telling me to have it serviced. only 3 of my 4 tires are registering on the system. Is there anyway to...

There is a Technical Service Bulletin (TSB) for your vehicle stating that if the light is blinking and if there are dashes (- -) on only one or two tire pressure readings, then the tire presure monitoring system should be put through a "Relearn" or "matching" process. Then if any of the tire pressure sensors do not respond while relearning, the sensor in that tire should be replaced.

The TPMS matching process is outlined below:

1. Set the parking brake.
2. Turn the ignition switch to ON/RUN with the engine off.
3. Go to the TPM vehicle information screen on the DIC. Press set to relearn the sensors. The horn sounds twice to signal the receiver is in relearn mode and Tire Learning Active message displays on the Driver Information Center screen.
4. Start with the driver side front tire.
5. Remove the valve cap from the valve stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for 10 seconds, or until a horn chirp sounds. The horn chirp, which can take up to 30 seconds to sound, confirms that the TPMS sensor identification code has been matched to this tire position.
6. Proceed to the passenger side front tire, and repeat the procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat the procedure in Step 5.
9. After hearing the confirming horn chirp, for the driver side rear tire, the horn sounds two more times to signal the tire learning mode is no longer active. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure level as indicated on the tire and loading information label.
11. Put the valve caps back on the valve stems.
The tires air pressure will not appear on the screen until you start driving the vehicle.

Aug 01, 2011 | 2010 Chevrolet Camaro

1 Answer

I rotated tires and now my low tire pressure light is on. how do I turn it off? I don"t have an owners manual.

You need to take it to a shop (Tire shops should have the tool) and have your Tire Pressure Monitor system reset. Your vehicle basically knows that the tires aren't where they are supposed to be. Just tell whoever you talk to that you need your tire sensors relearned. They may even do it for free as it will take 5mins or less.

Jun 15, 2011 | 2003 Chevrolet Impala

2 Answers

2010 cobalt need 2 know how 2 reset low tire pressure monitor

The low tire pressure warning should go out if you set all of the tire pressures to the correct pressure, then drive the vehicle for about a mile. You should not have to "relearn" the Tire Pressure Monitoring System (TPMS) unless the tires are (A.) rotated into different positions or (B.) There is a bad sensor that needs to be replaced.

For more information, you can read the information in your Owner's Manual. Here is a link to a pdf version 2009 Cobalt owners manual. (The information and procedures are the same for 2008 - 2010 Cobalts) The TPMS section starts on page 5-64

Cobalt Owner's Manual

Mar 30, 2011 | Chevrolet Cobalt Cars & Trucks

1 Answer

What to do since my service tire monitor has come on in my 2005 chevy suburban z71

You will need to bring it to a dealer or tire service center to see what the problem is.Most of the time it will be a sensor.Sometimes they can be just relearned.Also you may want to check your tire pressures.Make sure they are pressurized to what the pressure says on your door placard.

Dec 29, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

SVC Tire Monitor

If this warning came up soon after the tire was replaced then the most likely cause is the tire installer damaged the pressure sensor inside the tire. They are easy to damage.

Apr 29, 2009 | 2008 Chevrolet Malibu

Not finding what you are looking for?
2002 Chrysler 300M Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides