Question about 2002 Chrysler 300M

2 Answers

My tire reset

He i have a 2002 CHRYSLER 300m i put air in the tires and my computer inside does not read the same as the air gadge so i tried to reset it and it says training left front tire and then it will say training aborted how do i train my tire sensors?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi jess26, you should have a round magnet in your spare tire well. use the computer to train your sensors - it will tell you which wheel valve stem to put the magnet over - when horn honks move on to next one - last one is the spare. computer will tell you if all are re-trained. works good - have done it several times ...real easy Lotus26

Posted on Oct 11, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Heres what you do dont try to use the reset computer. the computer will reset it self. just make sure that when you put air in your tires the car is level... then using your tire guage bleed out each tire to 25 psi...now....pump your tires back up to 33psi each. i like to put in 33psi becouse when the tires heat up.. hot air expands so it should read 35psi to 36psi and thats ok.the computer will re set on is own after you,ve driven it around for a while.

Posted on Oct 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Notice slight shimmy between 30 and 45... Severl tires slightly low. Put air in tires and now shimmy is worse. Again at speeds of 30 to 45 while acceleration or slowing down.


Hi,
Could be tires need balanced. If they were run low on air, they could be worn and need replaced.

Also, front end suspension may need replaced: Struts/shocks, tie rods, ball joints, bushings. A shop can ID these parts to fix.

GL,
Td

Oct 10, 2012 | 2003 Chrysler 300M

1 Answer

My tires are wearing on the inside like my last car i replaced the outer tie rod ends and ball joints. But on my chrysler 300 2002 model ther looks to be more parts that look like ball joints than just one...


Your toe-in is off. Maybe tie rod ends or may just need alignment. If you take it for alignment, they will tell you if any joints are worn out.

Aug 27, 2010 | 2002 Chrysler 300M

1 Answer

How to change battery on chrysler 300m 2000


Your battery is located in the fender wall on the passenger side of the vehicle in front of the tire.You don't have to remove the tire but it will give you more room to work if you do.If you decide to remove the tire after tire is removed,remove the battery splash shield(the plastic with vent holes in it inside the fender towards the front).Slide the battery toward the rear of the vehicle and disconnect the cables from the battery.Installation is the reverse of removal.Make sure you connect the Negative cable last.

Aug 24, 2010 | 1999 Chrysler 300M

1 Answer

Jack placement on a 2002 chrysler 300m to fix a flat tire


Typically on Chrysler the lift point for the front tires is located just behind the wheel and for the rear just in front of the wheel. When you remove the cover that is over the spare tire there should be a diagram showing these. The User Manual will also designate these. These all assume you are using the original issued jack.

Jul 11, 2010 | 2002 Chrysler 300M

1 Answer

Does the fuel filter affect gas mileage


there are lots of things that can affect gas mileage. if the spark plugs and wires are worn out, the air filter being dirty, dirty fuel filter, proper inflation of the tires, O2 sensors that are contaminated and performing poorly. the first thing to do would be that the engine is in good working order, as in no check engine light, no misfire, etc. a poorly running engine will put out terrible gas mileage. then you can start with the things i listed.

Feb 21, 2010 | 2002 Chrysler 300M

1 Answer

How to reset my tire sensor for a 2002 300m and what type of coolant does it use also my spare tire sensor keeps going off


make sure your spare tire has 35psi, you can get your tire light to go off by makeing sure all tires are at 35psi then just drive the car a few miles(2-5) and the car will automaticaly turn light off. as for coolant the green conventional works just fine

Feb 19, 2010 | 2003 Chrysler 300M

1 Answer

Service Tire Pressure System - Chrysler 300M 2002


try disconnecting the battery for 15-20 minutes then check again/ Please rate my response thank you very much

Feb 01, 2009 | 2002 Chrysler Town & Country

2 Answers

Tires mounted on Chrysler Chrome Rime go flat when cold


it is most likely the valve stems. take off the caps and spray some soapy water in them and around the base. if there is a leak you will see bubbles.

Jan 14, 2009 | 1999 Chrysler 300M

1 Answer

Rotated tires on 2002 Chrysler 300M.


you need a magnet. there should have been one provided with the spare tire and jack. when you select retrain sensors you must put the magnet on the drivers front tire valve stem. once the vehicle has learned the sensore new position the horn will chirp then you move onto the next tire in a clockwise rotation without neglecting the spare if it is a full size mounted on a rim with a sensor

Jan 02, 2009 | 2002 Chrysler 300M

1 Answer

Tire pressure monitor relearn


that can only be done through the ecm(engine control module) main computer. you have to take it to a shop and have them reprogram the perameters with a scan tool. take it to a small shop it will be cheaper than going to a dealer. hope this helps......please rate this......thanks

Aug 31, 2008 | 2002 Chrysler 300M

Not finding what you are looking for?
2002 Chrysler 300M Logo

Related Topics:

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...