Question about 2002 Pontiac Grand Am

1 Answer

Car Horn 2002 Pontiac Grand AM horn does not work. Checked fuse - OK, tested for voltage at horn, nothing, tested relay- tested ok. I think I need to check the switch in the steering wheel but I don't know how to take it apart and I don't want to damage it.

Posted by on

  • 2 more comments 
  • Markn859 Sep 04, 2008

    I have put a jumper wire from the battery to the Horn and it works. I think the switch in the steering wheel is defective. How do I get to it ?

  • Amber Jun 06, 2012

    Hey Markn859, I have a grand am 2002 also and I looked at the fuses on mine because my horn also does not work, but I could not find the fuse for my horn so could you tell me where to find my fuse horn? Thanks a bunch!

  • Anonymous Mar 22, 2014

    my gauges stopped working need to know if there is a switch or something for it

  • Anonymous Mar 23, 2014

    Horn won't blow

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 55 Answers

Try using a 12volt jumper wire directly to the horn from the car battery. also check the ground on the horn. The last thing I would do is pull the steering wheel cover. Make sure the horn is blowing first.

Posted on Aug 31, 2008

  • John M. Pere' Jr. Sep 06, 2008


    1. Sorry for the delay we had a visit from GUSTAV here in LA. I have never removed a steering cover on your model auto but I have removed them on a chev and a ford. I looked to the rear or bottom of the wheel and some screws were there. Pull gently after removing the screws. Pay attentiom to the removel process. some springs might pop out. the whole assy rocks back and fourth - . you will also have to dis able the air bag- if you have one. once all is removed you will have to figure out how the switch works. most work on the contact basis. the cover around the colunm might help. I do not recomend you remove the cover. I would take the car to a mech shop. JOHN -LA.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Corvette horn not working


I have a 1999 corvette and the horn will not blow when pushing on the horn pad. It beeps when locking the car and security system.how do I locate the problem. Thanks Bob

Jul 12, 2012 | 1986 Chevrolet Corvette

1 Answer

2002 VW Beetle 1.8T\r\nRemoved horns and tested using battery & the both worked, reinstalled & press horn on steering wheel & nothing just hear a clicking noise from where I pushed on steering...


Generally the steering wheel boss switch does not wear out (the horn is not over used!). I would check the fuses and then the relay and if they look OK check the wiring form the relay to the horns for continuity. Use a voltmeter to check that voltage is being supplied to the relay when the horn switch is pressed. Then check that voltage is being output by the relay in response to this voltage input. If this all looks OK then there is some kind of break in the wiring to the horn unit

May 03, 2011 | 2002 Volkswagen Beetle Turbo S

1 Answer

The horn in my 96 pontiac sunfire isnt working. How would i go abou fixing that?


ok this problem could be in several places. most likely its a blown fuse or more likely a relay.check your owners manual for locations. if its not a fuse or relay then its in the horn itself or possibly in the contacts in the switch.The easy way to find it is unplug the horn have a friend depress the horn button and use a test light to see if you have voltage at the horn.if so replace horn. If not check the fuse if the fuse is blown replace and try again. if the fuse is not blown then check the relay.

Feb 28, 2011 | 1996 Pontiac Sunfire

1 Answer

Pontiac Grand Prix horn does not work. What is the best way to troubleshoot?


First, always check fuse.
2. If good, use test light at horn with button pressed to see if horn is getting voltage. If yes, replace horn.
3. If no, trace your way back--find horn relay in engine compartment fusebox and listen to see if it clicks when button is pushed. If yes, the wire from the relay to the horn is bad.
4. If no, remove the relay and test the socket for command signal from the horn button. See my tip at http://www.fixya.com/cars/r6022358-relay_check for how to check relay socket. If command signal is present, replace relay.
5. If not, the problem is with the wiring from the horn button to the relay.

Please let me know if you have questions

Sep 20, 2010 | 2004 Pontiac Grand Prix

1 Answer

94 pontiac bonneville horn does not work. i have checked fuse and it is good.


Ok , try this. have an other person push the horn button while you check for voltage at the horn wire. red wire from meter to horn wire and black to ground on car. should get 12 volts, or you can also use a test light. if it light up the circuit is good, or if you read 12 v on meter. replace horn. if not then find horn relay and replace it. sorry i'm not sure where that is located. might have to follow wire from horn back to it . possible under hood on the firewall. if that is not it then the only thing left is the switch in the steering wheel is not making contact. that is all to the horn circuit. hope this helps.

Sep 10, 2010 | 1994 Pontiac Bonneville

1 Answer

Horn will not work checked fuse relay lost


i would get a circuit light tester and start at the fuse for the horn to see if any voltage is available. then check to see if there is any voltage to the relay. if voltage is available at the fuse but not to the relay the problem is in the horn assembly in the colum if you get voltage to the relay but the horn doesnt work its the relay is bad.horns are also sujeted to the eliments on a pretty regular basis so it could also be a ground issue

Aug 31, 2010 | 2004 Pontiac Grand Am

4 Answers

Replace horn fuse in fuse panel of 1992 pontiac bonneville


Your fuse box is located on the driver side under the dash board. Up above where your brake and gas pedal are located. There should be a plastic cover that can be snapped off to reveal all of your fuses and on the inside of this plastic cover there should be a diagram of the fuses that are in use.

Feb 16, 2010 | 1992 Pontiac Bonneville

2 Answers

Horn stopped working, fuse and relay is good


With test light check voltage at horn assembly on both wire's, could only have one, horn assembly itself could be ground, have some one press horn button while checking, if there is voltage replace horn assembly, if no voltage horn pad at streeing wheel bad. that's being fuse and replay are good.

Jan 04, 2010 | 2007 Pontiac Solstice Convertible

2 Answers

2005 ford taurus horn just doesn't work. I've


The problem can be with the horn pad, the horn relay or the horn itself. Find your horn relay, it should be in the engine compartment fuse box. Remove the relay and test for power at the legs. there should be two legs that have power. If there is power there, take the cover off the relay and plug it back in. Squeez the relay points together and see if the horn works. If the horn still does not work, it is probably the horn itself. If it does work it is probably the horn pad, but you don't want to mess with that because of the air bag. Let a pro do it.

All of this is predicated on the fact that you have checked all the fuses.

Hope this helps
Rich

Aug 18, 2009 | 2005 Ford Taurus

1 Answer

Mercedes ML 320 1998. My horn does not work


About four things to do, first check voltage at horn with key on and button pressed. If voltage there try moving the small gap screw back and fourth a few times. If that doen't work replace horn. If no voltage check fuse and horn relay, you should be able to hear the relay click when you push the horn button, If not and fuse is ok. Switch relay out with another on on the car. If that doesn't fix it check the horn button for continuity.

Dec 27, 2008 | 1998 Mercedes-Benz M-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

572 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...