Question about 2004 Mitsubishi Lancer

1 Answer


Posted by on

  • SHIZZYIZM Aug 31, 2008

    04 mitsu lancer ralliart 2.4l



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 255 Answers

Hi, what kind of car,?? make ,model year,

Posted on Aug 31, 2008

  • Tony Rodriguez Aug 31, 2008

    Hi ,this is not so easy, but you can do it,, before you do anything else, remove the big nuts that holds the c v joints ,both of them,remove battery positive cable , ,, lift the car and remove both front tires, remove the right tie rod end ,remove the nuts that holds the ball joints(,they may have cutter pins) if so remove them, with a pray bar disconect both ball joints,remove both c v shafts ,position a jack under the engine ,remove transmission mount ,remove all thebolts that holds the transmission ,,... slowly lower the jack,pull the transmission back , that should do it ...



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i remove the 5sp transmission from my 2003 toyota celica gt

You need a lift, a hanger to hold the engine from the top a transmission jack and about 5 hrs.Disconnect battery. hang the engine from the support hanger. Remove front wheels. loosen and remove axle nuts. Loosen spindles and disconnect tie rod ends. Disconnect ABS sensors. Remove the axles. Disconnect everything from the subframe if equipped. Disconnect the transmission mount and drop the engine down to access the bell housing bolts. Remove bolts, after disconnecting all electrical and clutch controls. Support the transmission with a jack and remove. Reverse process to install.

Oct 20, 2014 | Toyota Celica Cars & Trucks

1 Answer

E30 clutch replacement

Drop the drive shaft, tranny cross member, transmission and bell housing. Remove the clutch pressure plate and disc and get new set. Use a pilot/clutch alignment tool in the crank shaft pilot bearing/bushing to center the disc and put the new pressure plate on and torque it down. Then put the bell housing, transmission, cross member, and drive shaft back in, and your done.

Nov 20, 2013 | BMW X5 Cars & Trucks

1 Answer

94 S 10 Blazer

The slave cylinder will be mounted on the bell housing and will push on an arm that comes out of the housing. It will have a bleed nipple (same type as on the brakes) at the end of the cylinder near the rubber hose attached to the cylinder .. (This is relevant if the clutch is not cable actuated). Regardless of wether it is 2WD --4WD or how many drives it has the clutch slave cylinder is attached to the bell housing and pushes on the clutch throw out arm in the bell housing. The bell housing is that section between the rear of the engine and the front of the gear box and houses the clutch assembly

Nov 16, 2013 | Cars & Trucks

1 Answer

Replace throwout barrings location install rattle when in gear.

get a service manual on CD over on ebay for about 5 bucks. jack car way up, drop the drive shaft, disconnect shifter and clutch linkage, unbolt the bell housing from the transmission and remove, unbolt pressure plate and take off flywheel, have flywheel resurfaced and reinstall, install new clutch and pressure plate, replace throwout bearing, put transmission and bell housing back in, connect shifter linkage and clutch cable or hydraulic, put drive shaft back in and you are done.

Jun 29, 2011 | 1996 Ford F150 Regular Cab

1 Answer

Do i need to drop the whole transmission, or can I just drop the bell housing to put a new clutch in? i have a 1995 saturn sc1

If its rear wheel drive you will have to pull the whole transmission. front wheel drive most likely the engine

Apr 28, 2011 | 1995 Saturn Sc

1 Answer

How do i put the new clutch asembly to my 1991 toyota pickup

drop the transmission. the clutch assembly is in the bell housing of the transmission. you will also have to pull the driveshaft. there are four bolts on the diff. pull those, push the driveshaft towards the tranny (light prybar may be needed) then it should pull out.

Feb 12, 2011 | 1992 Toyota Pickup

1 Answer

I'm trying to drop the transmission out of 1985 Dodge Lancer 2.2 L 4 Cyl. Turbo to install a new clutch kit. There is a lot of connections going into the bell housing and tranny which ones do disconnect?...

my favourite job ,i love clutches like i love ,well think of something ??,anyway you will need to disconnect the clutch ,gear change mechanism ,front suspension off and drive shafts out ,reverse light connection ,now some front wheel drive vehicles you have to lower the subframe as well .iam asuming its front wheel drive as i have never seen one ,now another trick i do to save time is to just open the bell housing about 3 inches then undo one bolt on the clutch at a time and turn flywheel with a big screwdriver ,then work out where the clutch bolts are in relation to the bell housing then drill a hole that i can get my 10mm socket through and in line with the clutch bolts ,then place new clutch in position and finger tighten bolts ,then refit bellhousing with a wiggle and as the clutch is loose it can move and align up .then when i have the bellhousing in place and bolts in and tight ,i can then tighten clutch bolts one at a time by turning ringear with a screwdriver but go round twice and their you are one clutch change ,shouldnt take including teabreak more than 3 hours .

Sep 30, 2010 | 1985 Dodge Lancer

1 Answer

I think my clutch master cillender is going out I loose preasure on my hydrolic clutch pedel. About how much will it cost for another master cillender and how do you change it?

depending on mileage you might be better off getting an entire clutch kit from advanced auto parts ~$350 and you'll have a new clutch, flywheel disc, and master cylinder. i replaced mine, but it is a pain. you have to drop the engine, remove the bell housing from the tranny to engine, then inside the bell housing is the master cylinder and it only has like two bolts that hold it on. once done remember to bleed your clutch.

Aug 16, 2010 | 2004 Chevrolet Cavalier

1 Answer

If the clutch slave cylinder on my 2005 Saturn Vue is internal to the transmission, how would the fluid have poured out onto my garage floor? I think the transmission dude might be pulling my leg to the...

No its internal meaning that its in the bell housing.The bell housing is bolted to the gearbox to hous the clutch befor being bolted to the engine.It has no seal on it.So when your slave cylinder leaks,The fluid drips from the bell housing.And the only way to get at it is to remove the gearbox.

Jul 17, 2009 | 2005 Saturn VUE

1 Answer

Clutch does not engage. cannot shift.

Probably the slave cylinder for the clutch has failed. On some models these are located on the outside of the bell housing and some are on the inside of the bell housing. If you find it located on the outside it's an easy fix. If you have a model with it located on the inside you will need to drop the transmission.

Oct 11, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8729 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides