Question about 1981 Ford Bronco

1 Answer

Bronco problem my ford bornco's starter will not dis engage after the key is released.what would cause this to happen?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

It could be a bad solanoid or low battery voltage will cause this at times ,also the switch itself could be bad, and it could be a bad bendix on the starter , wish i could be more help but its one of these many things

Posted on Sep 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 1989 bronco II quit running going down the road and now it will not start back


Check all connections. Battery cables, switch to starter cables, make sure they are all tight. Make sure the starter is engaging and disengaging. Check the belts for looseness. The fact that you were driving when it happened say`s something is loose!

Aug 29, 2014 | 1989 Ford Bronco II

1 Answer

Do i need a shim when replacing the starter on a 89" bronco II?


I am not certain whether you need a shim, but I would first check the flywheel for missing or worn teeth. Then check to be certain the teeth on the bendix are engaging the flywheel teeth. I hope this helps you find your problem.

Oct 16, 2013 | 1989 Ford Bronco II

1 Answer

Does a 1993 ford bronco (5.8) need a starter shim


No a shim is not required.If you are getting a high pitched noise when starter is engaged either starter drive gear is bad or flywheel teeth are missing.

Jan 10, 2011 | 1993 Ford Bronco

1 Answer

Zidane.tompsoni have a 1986 ford bronco 2 2.9 V6 im haveing some sorta electrical problem after driveing 3-8 minutes the fual pump will shut off and the truck dies i them try to start it up and the starter...


sounds like your fuel filter might be plugged causing the engine shutdown.
sounds like the solenoid on the starter is sticking causing your starter to stay engaged and powered up. the starter will stay powered up and will continue to spin until the starter solenoid is disengaged.
one other area to look at is the ignition switch. if that is bad it will continue to send a power signal to the starter solenoid keeping it engaged. so, you may want try unplugging that first, while your starter is running. if continues to run, then i would say it is the starter solenoid and not the switch. good luck

Sep 13, 2010 | 1986 Ford Bronco II

2 Answers

Looking to reinstall a solenoid for my 84 Bronco II and a buddy mixed up the wiring for it, i have no idea how to reconnect it to the new one.


Big wire from positive from battery goes to big stud facing the battery. Big wire to starter goes on other big stud. Little wire or wires go to little post. If you have 2 little posts they are labeled I (ignition) & S (starter). If you put on wrong little post it wont engage starter when you turn key to start. Just connect it to the other then it will engage starter when you turn the key to start.

Sep 09, 2010 | 1984 Ford Bronco II

2 Answers

The starter on my 86 bronco II flywheel issue


The solenoid on your starter is probably no good. Just get a new starter. Theres no starter that will "grab the teeth better", theres just new ones that work and old ones that **** out

Mar 25, 2010 | 1987 Ford Bronco II

1 Answer

I got a 89 bronco II and it wont start. Its got a new battery. I jumped out the starter relay and the starter engaged. So thats good. Also the relay clicks when you turn the key. Also checked the...


Im not sure what you mean by I jumped out the starter relay and the starter engaged.
so i am going to assume that you jumped from the battery side to the starter side on the relay and that engaged the starter... which is fine but you say the relay clicks when u turn the key. Pull off the clip on wire from the relay and push it against the battery side connection on the relay (u may need a small screwdriver to assist the connection) the relay should cause the starter to engage. If it just clicks (my bet) then you need to replace the relay (its really called a solenoid )

Feb 14, 2010 | 1989 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...