Question about 1998 Jeep Wrangler

1 Answer

1998 jeep wrangler sahara brake, tail and turn signal wont work

1998 jeep wrangler sahara brake, tail and turn signal won't work checked fuses and they all seem ok. Any ideas what could be causing this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 182 Answers

Did you go off road in the mud or woods?If so the connecting plug where all the connect probably has gotten disconnected.I think it is near or between the fuel tank and rear bumper.

Posted on Aug 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tail lights not working but the brake and turn signal works


no year, ? check the haz fuse. at left knee.? a wild guess. no year.
parking lights, the work on the front and rear. not just tail.
the parking lights and brake and turn all are controlled by the hazard module. and on jeeps , turns and brakes are a shared resource (blubs)
major warngler mile stones, all vastly different. are and i quote.
The Wrangler debuted in 1986 as a revision of the Jeep CJ-7, was revised in 1996, and completely redesigned in 2006

Nov 26, 2013 | Jeep Wrangler Cars & Trucks

1 Answer

2001 jeep wrangler. Brake lights won't work but


Check the brake control switch situated just above the break pedal arm under the dashboard. Could be a wire loose or unplugged or the switch itself could be faulty

Mar 07, 2013 | Cars & Trucks

1 Answer

I was wiring a trailer pigtail to an 06 wrangler and blew the turn signal bulbs but the fuses are good. I have running and reverse lights but no brake lights or turn signals


If the bulbs and the fuses are good, check the brake light switch. You might of shorted out the switch when working on the pig tail. Always use a test light or volt meter when installing pig tails. This way you can check for power and ground before hooking a wire up to help prevent shorts. But by what you have said it does sound as if the brake light switch is now bad.

Jun 27, 2010 | 2006 Jeep Wrangler

1 Answer

98 jeep wrangler headlights wont turn on


I would check your headlight relay switch that is located in your steering colum

May 19, 2009 | 1998 Jeep Wrangler

1 Answer

98 Jeep Wrangler turn signals and flashers don't work


The tail lights on the 98 use the screws that hold the light to the body of the jeep to ground the lights. Chances are the wholes that the screws/bolts goes into have a coating of rust around them and are stopping the lights from grounding. This may not be the solution but you need to eliminate this from your list.

Feb 19, 2009 | 1998 Jeep Wrangler

1 Answer

1998 wrangler turn signal/brake light short


your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Jul 30, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
1998 Jeep Wrangler Logo

Related Topics:

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...