Question about 1994 Oldsmobile 88

1 Answer

We are changing the water pump in my '94 OLds 88 my other brother suggested we change the idler pulley as well unsure how to do do this is thier a diagram or video on this or what do you suggest

Posted by on

  • Anonymous Nov 12, 2008

    the car gering hot

  • Anonymous Nov 12, 2008

    the car geringf hot









×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 169 Answers

If the pulley is not real loose or noisy when you spin it then leave it alone. Even a new pulley is a little loose as the play comes from the bearing inside it. here is a belt routing diagram you probably don't need. The threads on the pully are left hand thread. use the same wrench you used to remove the belt but go the opposite direction. good luck - here is the diagram you still don't need:http://www.ondemand5direct.com/app/Graphic.asp?S0=2097152&S1=0&SG=%7B9C3C573B%2D1C46%2D4AFC%2DAC24%2DEAD11C64CA9D%7D&YR=1994&MK=144&MD=1567&SM=1847&CAT=49&SCT=213&AG=A00051233&MKN=Oldsmobile&MDN=Eighty%2DEight+Royale&PS=524288&MA=15&SID=1069021359&MF=2&Ill=55360&Fig=9

Posted on Aug 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the 2006 Volvo S40 1.8l petrol model have timing belt or timing chain?


Belt, and in the 2006 it's due to be changed at 120000 miles. I wouldn't wait that long in an interference engine though. If it breaks, your engine is often toast when the valves and pistons impact.

The key is to not just replace the belt, but the idler pulley, tensioner pulley and the water pump while you're in there. Some people suggest going the water pump every OTHER belt (and pulley) change, but to me it's cheap insurance to do it every time.

Nov 04, 2013 | Volvo Cars & Trucks

2 Answers

Need the belt routining diagram for 1983 olds delta 88 royale, 5.0 liter engine


Air pump/Smog pump and Compressor go on first, on the shaft. Power steering goes on next Altenator is the last one. After market pulleys and the above mentioned parts may change this order.. 1983 olds delta 88 royale

Aug 19, 2011 | 1983 Oldsmobile Delta 88

2 Answers

How to change water pump on toyota sienna


3.0L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Wiper and blade assembly Top cowl seal and panel Window washer hoses, from the ventilator louvers Left and right ventilator louvers Heater air duct Timing belt
  5. Mark the left and right camshaft pulleys with a touch of paint.
  6. Remove or disconnect the following:
    NOTE Be sure not to mix up the pulleys.
    Right and left camshaft pulleys bolts Pulleys from the engine
    No. 2 idler pulley by removing the bolt 3 clamps and engine wire from the rear timing belt cover 6 No. 3 timing belt cover-to-engine bolts Water pump nuts/bolts Water pump and gasket from the engine

    9c53b11.jpg
    Fig. Exploded view of the components to gain access to the water pump-3.0L engine


    cf2cc65.jpg
    Fig. Exploded view of the water pump and related components-3.0L engine

To install:
  1. Check that the water pump turns smoothly. Also check the air hole for coolant leakage.
  2. Apply liquid sealer to the gasket, water pump and engine block.
  3. Install or connect the following:
    NOTE After tightening the bolt, be sure the idler pulley moves smoothly.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    Water pump, using a new gasket. Tighten the nuts/bolts to 53 inch lbs. (6 Nm). Rear timing belt cover. Tighten the 6 bolts to 74 inch lbs. (9 Nm). Engine wire with the 3 clamps to the rear timing belt cover No. 2 idler pulley. Tighten the bolt to 32 ft. lbs. (43 Nm).
    Right-hand camshaft pulley, with the flange side outward.
    Tighten the camshaft bolt to 65 ft. lbs. (88 Nm), using the removal tools Left-hand camshaft pulley, with the flange side inward.
    Tighten the camshaft bolt to 94 ft. lbs. (125 Nm), using the removal tools Timing belt
  4. Fill the engine coolant.
  5. Install or connect the following:
    Heater air duct Left and right ventilator louvers Window washer hoses to the ventilator louvers Top cowl seal and panel Wiper and blade assembly Negative battery cable
  6. Start the engine.
  7. Top off the engine coolant and check for leaks.

Hope this help.

Mar 23, 2010 | 2004 Toyota Sienna

1 Answer

How to change serpentine belt on 88 f150 6cyl


on the passenger side front, take a 1/2 in. ratchet, turn the ratchet till it comes to you. it will release the pressure off the serpentine belt. to replace beltstart from crank pulley up to the left side of the water pump, then to the alternator to underneath idler pulley over to the air conditioner over and down to the power steering.it mite take two pepole to do this.thin relise

Feb 21, 2010 | 1987 Ford F 150

2 Answers

We are tryng to remove a water pump from a 1998


there is a hole in the pulley for the power steering unit. That hole accesses the bolts to drop this unit down and then you can change the water pump. The trick is getting these two bolts lined back up to reinstall it

Oct 02, 2009 | 1998 Oldsmobile 88

2 Answers

How do I remove oil pump pulley to replace the water pump?


If you mean the power steering pump, it will have to be removed to access the bolt. It's just 2 bolts. You get them through the holes in the power steering pump. Just unbolt it and push it aside.

Feb 14, 2009 | 1995 Oldsmobile 88

1 Answer

Cannot remove the pulley from my 1991 olds cutlass ciera 's water pump. Its a 4cyl. Plus the new water pump doesn't look quite the same.


I replaced my water pump on my 92 olds, and the pulley will look slightly different because it's newer, but just make sure its the right one. The pulley does not come off of the water pump, both the water pump and pulley have to be changed. Your new one should come with both the pump and pulley already connected

Jan 05, 2009 | 1992 Oldsmobile Cutlass Ciera

2 Answers

1994 Olds 88 water pump repair


jack engine up and remove motor mount and you should be able to replace your water pump

Nov 17, 2008 | 1994 Oldsmobile 88

1 Answer

Idler pulley


i believe that loosening the powersteering pump and just moving aside would allow you to get at the bolts

Oct 15, 2008 | 1997 Pontiac Grand Prix

1 Answer

We are changing the water pump in my '94 OLds 88 how do we change the idler pulley while we are at it?


just un-screw the retainer bolt for the idler pulley. some of them are left hand thread and or require a #50 torx

Aug 30, 2008 | 1994 Oldsmobile 88

Not finding what you are looking for?
Cars & Trucks Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...