Question about 1992 Ford Crown Victoria

1 Answer

Brakes on the rear passenger side i need to replace the rotor and pads. where do i find the bleeder at?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

If you are only replacing pads and the rotor you should not need to open the bleeders. they are located on the calipers. all you have to do to back off the piston of the caliper is to use a small C-clamp. you place the stationary part on the back of caliper and the screw part on the piston of caliper. turn the screw until the piston moves back into the caliper housing this should allow you to put the new pads on and fit the caliper over the rotor. hope this helps. please rate this solution. thanks

Posted on Aug 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I bleed new brake calipers on a 2005 dodge power wagon?


your on the right track just make sure person on the brake pedal is holding them to the floor when you open bleeder and its closed all the way before the pedal is lifted, repeat till all air is out and you have a good stream of fluid coming out. and make sure your bleeding from furthest wheel away from master cylinder =1 passengers side rear,2 drivers side rear 3 passengers side front 4 drivers side front make sure you reset proportion valve just below master cylinder a rubber plug ,push it all the way in you'll know you got it when brake lite on dash goes out. I really hope this helped ,IF IT DID LET ME KNOW.
Woody

Sep 23, 2014 | Dodge Cars & Trucks

1 Answer

I have a 2006 Chrysler Sebring GTC and the passenger side rear brake is sticking. I have replaced the pads, rotors and caliper twice and bleed the brakes but the problem still persists. after about 15


Take it for a 10 minute drive. Jack up that wheel and try to spin t by hand. If it is hard to turn crack the bleeder screw and allow a little brake fluid to flow out. Tighten the bleeder screw and now turn by hand. If it turns easier than I would suspect a partially collapsed or collapsed brake hose.

Good luck and let me know what you find.

Sep 10, 2014 | 2006 Chrysler Sebring GTC

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

Replace rear brake discs and pads


Depending on vehicle. Find level ground and park there. Put chocks in front and behind wheels not being lifted. Loosen lugs, jack up vehicle, set jack stands, lower vehicle on jack stands, remove lugs and wheel. Open hood remove brake fluid cap. Remove two bolts holding caliper, pull caliper off rotor disc and bracket, remove pads, place a used pad in front of caliper piston, use a c clamp to push caliper piston in caliper, remove c clamp and old pad, hang caliper up, remove 2 bolts holding caliper bracket, remove bracket, remove rotor, install new rotor, install caliper bracket, install new pads, install caliper, repeat this on other side, put cap back on brake fluid tank, remove bleeder fittings and keep pressing brake pedal until an even flow of brake fluid sprays out. Install bleeder fitting. Make sure brake fluid doesnt get on paint and is contained and disposed of correctly, top off fluid install wheels and raise car up remove jack stands, lower car and break in new pads

Nov 06, 2013 | Cars & Trucks

1 Answer

1999 mustang 3.8 my rear passenger break is sticking I just replaced them and when I did it the inside was compleatly worn but the outside break was practically new most of the pad was still their


The three most common reasons for brakes to stay applied is a faulty caliper, brake hose, or the caliper is not sliding on the spindle.
When the brakes are applied then released, do the pads stay against the rotor, and can you release them by opening the bleeder screw ?

Jul 07, 2013 | Cars & Trucks

1 Answer

How to replace rear brake pads on 2002 buick rendevous


Those are special calipers. The piston cannot be just compressed back into the caliper - it needs to be turned as it is compressed or you can ruin the caliper.There is a kit you can rent from AutoZone or many independent auto parts stores that will perform both functions at the same time.
Block fron wheels and raise vehicle passenger side. Remove wheel. The caliper is on the top rear side of the assembly you're looking at.There are 2 long bolts you'll need to remove to take the caliper off the vehicle. Don't remove the brake line or open the bleeder screw ( either of these moves will add to your work!! ) Insert a large flat blade screwdriver in between the rotor and outboard brake pad and pry away from the vehicle slightly to release the pads from the rotor. Slide caliper upwards and towards the back of the vehicle to separate from rotor. The pads will come in a full set ( all 4 pads for both side of the rear ) . Look at your replacement pads and determine if they have a retainer clip holding them in place or a compression clip. Remove outboard pad first then inboard. Match old pads to replacement pads. Inspect rotor for grooves and irregular surfaces - if any grooves or irregularity present, remove rotor and take to an auto parts store for refinishing.Compress caliper piston with kit and allow 5 minutes for pressure to bleed back into the master cylinder.install rotor if removed and wipe surfaces with brake clean. Install inboard then outboard pad and place caliper on rotor, then mount to vehicle. Install wheel, repeat procedure for drivers side, then PUMP BRAKE PEDAL 5 TIMES BEFORE TRYING TO DRIVE VEHICLE to set pads on rotors.

Nov 26, 2010 | 2003 Buick Rendezvous

1 Answer

How to replace rear brake pads on 2004 Jeep Cherokee 4x4


take it to a mechanic....;) I have a 2003 jeep grand cherokee 4 wheel drive V8. there probably is not much difference between year models. frist thing remove the back tire you will see the caliper and rotor. check the rotor if it has deep groves on the front or back you will need to bring it in to have it turned or replaced if it is still smooth it should be ok. remove the caliper by taking the two bolts off the back of the caliper. using a pice of wire hang the caliper so it isn't dangling from the brake line. Now is the time to replace rotor if needed .Get a pair of vice grips crimp off the brake line so any trash in the caliper doesn't get into the brake system (if you let the contaminants get into the brake system it can cause costly repairs to the abs system). open up the bleeder valve most of the time close to where the brake line goes into the caliper and usually has a rubber cap. open bleeder valve, take a c-clamp place on inner brake pad and outside of caliper tighten until caliper is all of the way open close bleeder valve. replace brake pads put caliper back on recommend using lock tight on bolts holding caliper on snug fasteners but do not over tighten, lock tight will keep bolts from backing out. do the other side the same way. pull up emergency brake to and pump brake pedal to adjust brakes. bleed brakes and you are done

Nov 14, 2009 | 2004 Jeep Grand Cherokee

2 Answers

I just replaced both front rotors and pads, along with the driver side caliper. My next step is to now bleed the brakes. my question is do i need to bleed all 4 brakes or just the 1 that was replaced?


you don't need to bleed front brakes if you only did rotors and pads. If you look at the master cylindar, there are 4 lines coming off of it, one for each brake. Only bleed what you replaced.

Sep 29, 2009 | 2002 Hyundai Accent

1 Answer

2000 chevy 1500 silverado- rear brakes overheating


Have someone push & release pedal while at wheel with problem. See if it takes a while or slow to release. If yes, have wrench ready on bleeder screw, and try again, if it sticks/holds, crack bleeder screw, if it releases, I'd replace hose.

Jan 18, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

New brakes


Still have air inside, because you used gravity feed method.

Jul 17, 2008 | 2000 Chrysler Cirrus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...