Question about 1994 Chrysler Concorde

1 Answer

Starter having problems getting starter out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Can you explain specifically what you have done so far as removing the starter

Posted on Aug 30, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Starter problems

Relay faulty that controls starter or alarm. If you have to hit your starter to get it to work, starter is faulty. IF starter and realy is 1 unit, replace both.

Dec 15, 2013 | Cars & Trucks

1 Answer

Problems with power to starter

what is the make and model and year please? you are saying the starter was jumped to start your truck. I am hoping you do not have a new truck.

Feb 11, 2013 | Cars & Trucks

1 Answer

Hi - I have a BMW 520i (1997) which I have had off the road for a few months. I have tried o start it but all I get is a knocking noise from the top of the engine, the engine does not turn. I have...

Have you determined that the starter is getting the voltage/current at its terminals? It is unlikely that the starter seized after only a few months. If you have someone else available, have them hold the key to the start position while you hit the starter motor with a hammer. If the starter begins cranking, your problem is likely sticking brushes in the starter motor. If that's the case, remove the starter motor and disassemble to address the problem or get another starter motor.

Jun 25, 2011 | 1997 BMW 5 Series

1 Answer

Are 2003 chevy s-10s known for having starter problems? We bought a used s-10 with AT and 4 cylinder, with about 140,000 miles on it. The starter was going bad, so i replaced it. Worked fine for about a...

This is not a recurring problem for this truck, you just got a bad starter, get a good starter like from NAPA and you wont have to deal with this problem again.

Jun 28, 2010 | 2003 Chevrolet S-10

2 Answers

03 Oldsmobile Silhouette 3.4L Starter stays engaged at times.

Sounds like time for a new starter. While it could be electrical, in that the starter circuit is remaining engaged, more than likely it is mechanical. As the starter wears, you get play in the starter gear. Replacing the starter should take care of it. If you have recently had the starter off or replaced it, it could be misaligned, causing a similar problem.

Mar 27, 2010 | 2003 Oldsmobile Silhouette

3 Answers

Randomly dont start. if i tap on starter it will start up. have had starter replaced 2 times but still happens even if i touch starter with a metal object its arks and starts right up its a 2007 its...

seems that the starter is getting heat soaked, or is some how absorbing voltage. very wierd. I would go over all your grounds and get a new starter installed, but ask to see the old one

Oct 28, 2009 | 2007 Jeep Grand Cherokee Overland

2 Answers

Starter problem- How do I check to see if the starter needs replaced?

check to see if your getting power from the battery to the starter and check the ignition signal wire while some one turns the key if your getting power there and the starter don't engage then the starter needs to be replaced also while someone trys to start it tap on the starter and see if you get a response but if your getting power to it and it don't work it's bad

Oct 19, 2009 | 2000 GMC Jimmy

1 Answer

Is there any other suggestion(to have checked) you have regarding my 2003 camry starting problem before I have it towed again today for service?I just spoke with the repair shop this morning and they...

Yes you can have them use an ohm meter to test the relay integration switch to make sure that power is going through it. That being said, the fact that they can tap the solenoid on the starter and it works to get the car started makes be think that the starter has gone bad again. It doesn't make sense that you replaced it just 3 days ago and it needs to be replaced again. To me, that means that the starter you got was bad and there should be some sort of warranty for that, even 90 days, and it should be covered under that for a new starter for free. Good luck and thanks for using FixYa!

Jul 13, 2009 | Toyota Camry Cars & Trucks

2 Answers

Turn on ignition and get nothing but clicks

sound like bad starter solenoid or bad starter.

May 10, 2009 | 1997 Ford Explorer AWD

2 Answers

Starter problems

Try to check battery. If it is fully charged it might be still starter.
Beacause you used rebuilt starter. For most Acura, Honda, Toyota
using rebuilt starter is not appropriate as it wont do the same job as brand new. You have to use brand new.
Good Luck

Jan 14, 2009 | 1997 Acura TL Series

Not finding what you are looking for?
1994 Chrysler Concorde Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides