Question about 1992 Oldsmobile Cutlass Ciera

1 Answer

Car idles good revs up good but when i put it in drive or reverse it stalls

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

Dear friend-the reason why your vehicle cuts is because as soon as you engage the idling drops,fitted to your vehicle is a module that picks up the idling,find that unit and your problem will be solved.

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my truck die when I put it in drive


Stalls when put into Drive or Reverse - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 1987 - 1996 F150 & Larger F-Series Trucks
May 22, 2012 - Stalls when put into Drive or Reverse 1987 - 1996 F150 & Larger ... the fluid that was needed...my truck would stall when I shifted into reverse. 1995 Bronco stalls when put into drive
Jun 13, 2013
ford powerstroke truck dies in reverse
Oct 29, 2011
Truck dies when putting in gear and giving it gas.
Feb 26, 2011
ENGINE IDLES FINE,DIES WHEN PUT IN DRIVE
Jun 26, 2010
More results from www.ford-trucks.com

TRUCK DIES WHEN PUT IN REVERS


Nov 30, 2015 | Cars & Trucks

1 Answer

Tranny has a 3 speed auto with overdrive.when i put in drive the motor stalls,when i put in reverse i can get it to idle in reverse after powerbraking down to idle which takes me about 10 seconds.when i do...


Hi look like its your lockup stay on it depend on the car on gm you can remove the luckup switch on the trany or remove the side cover on the driver side and change that bad lockup selenoid

Mar 15, 2015 | Cars & Trucks

1 Answer

I have a 1998 ford explorer It idles ok but stalls when you rev it up or put it in drive or reverse and try to go. I have replaced the fuel filter and plugs and installed injector cleaner and dry gas....


Sounds like a lean fuel condition. If fuel pressure is good, I would suspect a dirty or faulty mass airflow sensor. Try disconnecting the sensor in the air intake tube near the air filter. If the problem goes away, replace the sensor.

Nov 16, 2014 | Ford Explorer Cars & Trucks

1 Answer

Just replaced heater core, now car dies when put in gear


check for pinch wires around core install. also a vacume leak from same job not plugged

Dec 03, 2013 | 1998 Mercury Grand Marquis

1 Answer

I have a F250 lariat with a 460 - truck stalls when I put it in gear - even after it runs for 20 min. Sometimes it will stall while I'm driving. I had carborator replaced last year. Hope you can help.


Some possible causes could be:

Vacuum leaks cause an engine to run lean witch can cause the vehicle to stall when put into gear.

Improper base idle adjustment can cause the vehicle to stall when shifted into drive or reverse

A malfunctioning or damaged carburetor can cause the vehicle to stall when shifted into drive or reverse

Improper ignition timing can cause the vehicle to stall when shifted into drive or reverse.

A malfunctioning or damaged transmission or torque converter can cause the vehicle to stall when shifted into drive or reverse

Oct 31, 2010 | 1987 Ford F 250

1 Answer

My 1995 suzuki sidekick idling problem


Check if you put back all the air (vacuum hoses) hoses to their proper places. You might inter change them making the EGR valve open. Also check your fuel filter and fuel injectors.

Mar 12, 2009 | 1995 Suzuki Sidekick

1 Answer

Idles irradictly when in drive saab 900s 1995


It sounds like you may have a vacuum leak. A good way to check for a leak is to take a squirt bottle with water in it, and with the engine COLD and the engine at idle, spray some water around where the intake mainifold and the head meet. If the idle changes you found your leak, also spray any vacume hoses. Stay away from the alternater.

Feb 16, 2009 | 1997 Saab 900

Not finding what you are looking for?
1992 Oldsmobile Cutlass Ciera Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...