Question about 1990 Subaru Legacy

2 Answers

Drive axle and cv joint

How can I remove the right side inner CV joint to replace the boot?

Posted by on

2 Answers

The shaft and the ball cage are already off. the inner piece that goes into the gearbox is not coming out. the boot was changed and I now need to reassemble the parts.

Posted on Aug 30, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 169 Answers

Have you already removed the axle from the car?

Posted on Aug 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My front of my car vibrates like crazy everytime I accelerate and turn right but when I let off the has it stops


Sounds like maybe a busted motor mount or transmission mount, or a worn out cv drive axle.Look under the front of the car at the drive axles there is 4 rubber boots 2 on each axle inner boot and outer boot.See if one or more of the boots is torn or split.

Jan 20, 2013 | Cars & Trucks

1 Answer

How to replace the front outer boot


The outer CV-joint boot can be serviced or replaced by removing the inner CV-joint. Click this link below for replacing instructions:--- http://repairhelpcenter.blogspot.com/2011/10/how-to-replace-front-drive-axle-cv.html ----------- This will help.Thanks.Helpmech.

Oct 17, 2011 | 2003 Chevrolet Tracker

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

Im trying to replace the driver side cv. the inner boot came off with the whole drive axcel, except for the inner spine. it looks lkike the previous owner removed the inner cv joint and replaced the boot...


YOU HAVE TO REMOVE WHOLE AXLE AN INSTALL AXLE IN INNER CV JIONT THEN MAKE SURE IT CLIPS IN,INSTALL BOOT AN RECLAMP CV BOOT WITH SPECIALLTY PLIERS

Dec 21, 2010 | Mazda 323 Cars & Trucks

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

1997 Pathfinder How do you replace the left outer cv boot?


How to Replace a CV Boot
( DIY Complexity: Hard / Time: 3.2 hours )

Parts:
1. CV Boot
2. CV Boot Clamp Kit

Tools:
1. Mallet Hammer
2. 3/8 in. Drive Ratchet
3. Combination Wrench Set
4. Floor Jack
5. Flashlight
6. Flat Head Screwdriver
7. Socket Set
8. Tire Iron

Steps:
Step 1 Secure the vehicle on a level surface, making sure the vehicle will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Lift up the front of the vehicle using a jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Find the correct size socket and large ratchet or tire iron and turn the wheel lug nuts counter clockwise. Remove the front wheels.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the CV boot for damage.
o Tip: The CV joint may be worn if the boot is damaged. Thoroughly inspect the CV joint assembly before installing the new boot. If the CV joint is damaged, replace the entire CV joint axle assembly.

Step 6 Mark the axle for installation reference. Remove the CV joint axle assembly.

Step 7 Using a bench vise, hold the shaft of the CV joint secure so that you can separate the CV joint from the shaft. Remove the CV boot clamps.

Step 8 Slide the CV boot off the outer CV joint.

Step 9 Using a rubber mallet, knock the CV joint off of the axle shaft.

Step 10 Remove the old boot from the CV axle shaft and wipe off any old grease. Clean the sealing surface on the CV joint.

Step 11 Fill the CV joint with grease and get it ready to slide back onto the shaft.

Step 12 Slide the new boot onto the shaft but do not tighten the inner clamp yet. Install a new retaining clip before putting the joint and axle together.

Step 13 Slide the CV joint back onto the axle shaft completely.

Step 14 Pack the boot with grease and slide the boot over the CV joint housing. Secure the boot with new clamps.

Step 15 Install the CV joint and axle back into the vehicle in the reverse order that it was removed.

Step 16 Mount the wheel back onto the hub assembly.

Step 17 Tighten lug nuts in a star pattern and torque to suggested manufacturer specifications in the vehicle owner’s manual.

Step 18 Remove jack stands.

Step 19 Lower vehicle with jack until it is securely on the ground.

Step 20 Drive the vehicle to make sure that any noises are no longer present and that there are no indications of wearing parts. Before road testing, visually inspect the area you have worked on to make sure everything is tightened and assembled properly.

Hope help with this (remember rated and comment this help).

Mar 12, 2010 | 1997 Nissan Pathfinder

1 Answer

CV axle removal 1999 Isuzu Trooper


The easy way is to take the inner boot off and take the joint apart. Take new cv axle apart at inner joint and attach to the old one sticking out of axle housing. You will need to get new boot clamp.

Mar 03, 2010 | 2003 Lincoln Town Car

1 Answer

My driver side cv joint inner boot keeps breaking


Are you replacing the cv axle yourself. If you are going with an aftermarket axle, that may be your problem. I would recommend going back to O.E. Also, some original saturn parts may be hard to find.

Feb 02, 2010 | 1999 Saturn SL

2 Answers

Inner cv joints


inner cv joints are the joints on the inner half of the axle shaftswhere they go into the transmission. sometimes the easiest thing to do is replace the axle shafts

Jan 05, 2009 | 1996 Chrysler LHS

2 Answers

94 Geo Prizm CV or driveaxle?


on this type of vehichle, you have two axles in the front; one going to each side. Chances are that the boot at the axle joint was torn and that is why you are having problem. In teh past people used to replace the boot, this day and age its actually cheaper to replace the axle. So you would need to replace that side of the axle (the half shaft).

Nov 19, 2008 | 1994 Geo Prizm

Not finding what you are looking for?
1990 Subaru Legacy Logo

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...