Question about 1999 Daewoo Nubira

1 Answer

Removal of window winder assembly for 1500 Daewoo

Hi guys. Trying to fina a diagram of the above. The window winder cable has broken and I can't work out where it is attached to as it is inside the door frame assembly. Can you help?
Cheers,
Stephen Adelaide South Australia Australia
please note: the car is a 1994 Daewoo sedan but you didn't have that as a category :)

Posted by on

  • TheMoser63 Aug 30, 2008

    Please refer to the above.

    Cheers,

    TheMoser63

×

1 Answer

If your in adelaide call a place called new model wreckers in sydney. There service is realy good. i speak to a guy called dave there

Posted on Sep 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

RH electric window winder cable broken can I replace cable or have to replace whole motor cable set up


Hi Ian you need to replace the whole window regulator. Some new ones come with the motor and some without. Regards Jim...

May 19, 2015 | 2003 Kia Spectra

1 Answer

How do I fix front window came off roller can't wind up


Door card will need removal and possibly a new door window mech as the window runs up and down a runner by a cable and either motor or winder. Sometimes you can put them back in but more often than not something has broken.

Oct 15, 2014 | Cars & Trucks

1 Answer

I need an Illustrated Parts Break down for a 1989 GMC Sierra 1500. 350 w/ PS/PB loaded. Steering column Removal Repair or Replace


Hi.

Below you get all the parts breakdown for GMC Sierra 1500, including steering column assembly:

1500 SIERRA

Here diagrams for all 1989 GMC trucks.

If you need to take apart the steering column you will also need wiring. below the color codes and wiring tips:

GMC SIERRA 1988-2005 VEHICLE WIRING

Regards.

Ginko

Aug 31, 2011 | GMC C1500 Cars & Trucks

1 Answer

The front side driver's window won't roll up.


you shoud replace the window winder motor/assembly. the cable from the motor has likely broken loose from the asembly bracket. this can sometimes be repaired, but any professional mechanic would just replace the whole assembly. fixing the assembly is somewhat of a jimmy-rig, and it doesnt always last very long.

Mar 26, 2011 | 1998 Volkswagen Jetta

1 Answer

How do change low beam lightbulb on a 2007 dodge ram 1500


Removal & Installation-Get at it from behind the lens assembly.
These instructions show how to remove and replace the whole light assembly but shows a diagram
on what it looks like.

To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following: dod_ram15_02-04_headlmp.gif

    • Negative battery cable
    • Push pins
    • Bolts connecting headlamp unit to fender
    • Bulb sockets from headlamp unit
    • Headlamp unit
To Install:
  1. Install or connect the following:
    • Bulb sockets
    • Headlamp unit to fender with the bolts
    • Seal and push pins
    • Negative battery cable
prev.gif next.gif

Jan 14, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

I have a power window on driver's side that has been laboring to close for awile. Today the window would not go up all the way with a crunching noise. I could push it down with manual assistance. Upon...


Hi!!
That assembly is call the window regulator or elevator. An you can get a replacement without the motor, they run about $100 and is sold at most autoparts stores.
Good Luck!! Don't forget to rate this post!

Oct 01, 2010 | 2002 Chevrolet Silverado 1500

1 Answer

How do I remove the window winder mechanism on the drivers side door? The window is stuck partly open and I can't seem to move it. Peter


The fault is with the regulator on the window. Remove winder and door handles. Remove door lining and reconnect window to winder rail. Reverse for reassembly

Mar 17, 2010 | 1999 Daewoo Nubira

1 Answer

Power window regulator has a broken cable on my dodge ram van


it would be alot less stressful if you just replace the whole thing from a salvage yard

Dec 27, 2009 | 2004 Dodge Ram 1500

1 Answer

Front driver's door won't lock on my 1999 Daewoo Lanos SE


it is attached with a wire clip and there s a very affordable removal tool which slips behind the crank handle and pushes it out....it can be dug out with a hook scribe but a bit frustrating and can cause minor damage to the trim

Jul 01, 2009 | 2000 Daewoo Lanos

1 Answer

I need to remove the drivers internal door panel


Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Feb 04, 2009 | 2001 Suzuki Swift

Not finding what you are looking for?
1999 Daewoo Nubira Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...