Question about 2003 BMW 330

2 Answers

03 330i transmission indicator lamp on

My bmw trans light came on and will only shift 3rd and 4th gear now. Is there a reset ? Any ideas ?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 111 Answers

What was the problem?

Posted on Oct 04, 2008

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 39 Answers

I had same proble need to take to transmission place asap

Posted on Aug 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does s3 and s4 on integra start flashing


I found this one the www.hondacarforum.com
http://www.hondacarforum.com/honda-technical/28562-i-have-1989-honda-integra-can-any-one-tell-me-what-s4-gear-stick.html

You have a couple of choices on this Honda transmission... D and S modes. Consider the D as the normal Drive mode and the S for Sport mode. The difference between the two is that in "D", the transmission will shift through the gears all the way to 4th gear and at lower rpm shift points. In "S", the transmission will shift at higher rpm levels and will go no higher than 3rd gear and light S3 on the dash. Once the vehicle is in 3rd gear (S3) you can then press the S4 button and the transmission will go into 4th gear (when conditions dictate). I believe there is even an S4 indicator on the dash signifying the trans is in 4th gear

The last line looks like it is the key here though.

If the car thinks its in 4th gear when you are trying to start it, obviously it wouldn't start...you could probably hunt around and see if there is a sensor on the transmission stick that runs the "D" vs "S" mode

Feb 06, 2010 | 1990 Acura Integra Hatchback

1 Answer

Only runs in 1st and 2nd gear and reverse.


This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans shifts into gear harshly, car feels sluggish off the line
, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Dec 14, 2009 | 2006 Hummer H3

1 Answer

Its 2 wheel drive, but the transmission won't shift unless you manuallyl put the gear shifter in low then work your way up to get the gears to change. The gears work fine it just won't change on its on. If...


Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under-hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Good luck and keep me posted, there are other things but these things mentioned seam like what you described.

Nov 19, 2009 | 1993 Isuzu Rodeo

1 Answer

4L 60E - 2001 k1500 will not shift into 3-4. Oil is not burn't and stifts great into1-2


  • No 3rd or 4th gear: “3-4” clutches are worn out. R&R. The car is safe to drive (in 2) until you can get it fixed.
  • Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.
  • No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : Shift A solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.
Check to see if your transmission is in the limp mode, which would only give you 2nd, 3rd and reverse gears. No 1st or 4th gear.

Nov 19, 2009 | 2003 GMC Sierra 1500

1 Answer

Trans drops into 3rd gear won,t shift to 4th


DTC P0734 is "4th gear incorrect ratio" - that's your torque converter 'LOCK UP Clutch" It's worn out (or you're using the wrong Trans Fluid required by Hyundai - SPIII OR Both). The P1624 is simply the Trans Control Unit (computer) communicating to the Engine Control Module (ECM computer) MIL - on request signal to ECM = asking it to turn on "Check Engine" light. MIL = Malfunction Indicator Lamp. When the torque converter 'lock up" clutch slips or doesn't engage, the trans automatically returns to 3rd gear and stays there (it's called 'fail safe' mode) until you cycle the ignition key, then everything resets until the malfunction occurs again.
You'll need to have an AT (Automatic Transaxel) tester hooked up to verify this. Hyundai has a Service Bulletin specifically for "gear incorrect ratio' codes. If when you changed the trans fluid, was it done at a Hyundai Service Center? If not, someone may have installed the wrong fluid.

Jun 01, 2009 | 2000 Hyundai Elantra

1 Answer

Transmission won't shift to 2nd and 3rd gears goes from 1st to 4th.


Doesn't sound like a simple fix. I would suggest having it serviced.

May 05, 2009 | BMW 318 Cars & Trucks

1 Answer

My s4 light on my 1989 honda integra is flashing and car only will start when light stops flashing whitch happens when ever it likes 2


I found this one the www.hondacarforum.com
http://www.hondacarforum.com/honda-technical/28562-i-have-1989-honda-integra-can-any-one-tell-me-what-s4-gear-stick.html

You have a couple of choices on this Honda transmission... D and S modes. Consider the D as the normal Drive mode and the S for Sport mode. The difference between the two is that in "D", the transmission will shift through the gears all the way to 4th gear and at lower rpm shift points. In "S", the transmission will shift at higher rpm levels and will go no higher than 3rd gear and light S3 on the dash. Once the vehicle is in 3rd gear (S3) you can then press the S4 button and the transmission will go into 4th gear (when conditions dictate). I believe there is even an S4 indicator on the dash signifying the trans is in 4th gear

The last line looks like it is the key here though.

If the car thinks its in 4th gear when you are trying to start it, obviously it wouldn't start...you could probably hunt around and see if there is a sensor on the transmission stick that runs the "D" vs "S" mode

Mar 04, 2009 | 1989 Honda Accord 4 Door

3 Answers

E40d trans will not shift into 3rd or 4th gear, only rev. 1+2


check or replace your thottle position sensor tps that trans needs to know where the throttle is to shift if it is bad it will do as you say wont shift to third
another telltale is it will act like it goes into lockup when shifting into reverse and stall the engine

Jan 23, 2009 | 1995 Ford Club Chateau

2 Answers

98 Civic Auto Trans Slippage


you need to replace clutch pack for that gear can be ordered seperately from parts store or dealer if you want to save money call peach street auto recycling at 1800-365-2341 for a warrantied used one! also might be time for change trans filter and fluid filter could be slightly clogged but I lean towards clutch pack I replace these alot on Hondas

Dec 12, 2008 | 1998 Honda Civic

1 Answer

Automatic gears


Honda transmissions,as well as most other overdrive transmissions,should be driven at all times in drive 4,or the overdrive position,with the exception of severe driving conditions,such as towing a load,extremely hilly terrain,or long uphill grades,the trans should be taken out of overdrive,and placed in the drive 3 position.This is to prevent the perpetual shifting back and forth of the trans from 3rd into 4th,back to 3rd,back to 4th,back to 3rd,that would eventually damage both the 3rd and 4th gear clutch discs and components.

Aug 08, 2008 | 1994 Honda Civic

Not finding what you are looking for?
2003 BMW 330 Logo

Related Topics:

802 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...