Question about Nissan Se R

2 Answers

Nissan skyline 1996 model: abs light always on. had it diagnosed and result was "off failure". could be loose wiring? please advise...

Posted by on

  • Skyline Chic Apr 12, 2009

    My light started flicking in and out and now it stays on got a digonostics done on it and got told there is a problem in the main unit or the fuses could be blowen I have cheeked all the fuses in the car and under the bonnet and they are fine so I am now going to change my back brakes and see if that works always start with the cheepist thing first as all of this needs to be done anyway so it is best to start there good luck to the both of us hope we can fix the problem soon.



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I took my skyline to an auto sparkry and found out it was just a relay that is under the hood and attached to the abs pump motor what eva you want to call it so i would see a sparkey so thay can c if it has cooked it self good luck

Posted on Apr 19, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 474 Answers

I would try checking for a bad fuse or bad wheel speed sensor.

Posted on Aug 30, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do I erase the ABS light or reset it?

you will need a code reader. you can also disconnect the battery for 15 minutes or so and this will clear active codes. If you start it and it comes back on you have a fault you will need to diagnose.

Jul 06, 2016 | 1996 Nissan Maxima

1 Answer

Abs light on nissan pulsar 2005 model why

there is a code set in the abs module that needs to be checked out to help find were to start diagnosing. it could be a wheel speed sensor, poor connection, broken wire, problem with the abs hydraulic unit so the code needs to be pulled and system repaired to put out light, note that until this is fixed you have no abs working and your braking like a car without abs.

Aug 24, 2014 | Cars & Trucks

1 Answer

Light abs traction control stays 1998 buick park avenue

PRE-DIAGNOSTIC INSPECTIONBefore diagnosing ABS/TCS, perform a comprehensive visual inspection of system as follows.Check ABS/TCS wiring harness connectors for looseness. Check harness routing; pay particular attention to wheel speed sensor wiring harness routing. Check fuses No. 1D, 5B and 6B in instrument panel fuse block. Check fuses No. 1 and 2 in underhood fuse block. Check brake fluid level in master cylinder reservoir. Check brake fluid level in Pressure Modulator Valve (PMV) assembly reservoir. Ensure parking brake is fully released. Ensure parking brake switch is functioning properly. Always perform ABS/TCS system functional check before using DIAGNOSTIC CODE CHARTSThe EBCM/EBTCM has self-diagnostic capability, which can detect system failures. Fault codes stored by EBCM/EBTCM can be displayed using Tech 1 scan tester. There are no provisions for flash code diagnostics.Begin ABS/TCS diagnosis with PRE-DIAGNOSTIC INSPECTION procedure. If failures are found during pre-diagnostic inspection, perform necessary repairs, and proceed with ABS/TCS FUNCTIONAL CHECK. See Fig. 5 .If no failures are found during pre-diagnostic inspection, go to ABS/TCS FUNCTIONAL CHECK. See Fig. 5 . The ABS/TCS FUNCTIONAL CHECK will either indicate ABS/TCS is functioning properly or direct technician to various diagnostic procedures such as diagnostic charts, symptom diagnosis or BRAKE warning light diagnosis.CHART D - TRACTION OFF WARNING LIGHT ON CONTINUOUSLY & NO DTC SET (BUICK WITH UH8 OR U2A INSTRUMENT CLUSTER)Circuit DescriptionWhen ignition switch is first turned to RUN position, EBTCM goes through a self-test, which lasts 2-4 seconds. During self-test, EBTCM commands TRACTION OFF indicator warning light on. Powertrain Control Module (PCM) can also command EBTCM to set a Code 75 which will illuminate TRACTION OFF indicator.Traction control switch is located either on instrument panel center trim plate or driver's front door trim panel. Switch allows driver to select traction control mode (on/off). When traction control system is turned off, TRACTION OFF warning light comes on.EBTCM monitors transaxle temperature through

Jul 12, 2014 | 1998 Buick Park Avenue

1 Answer

I have a 1997 skyline gts. Few days ago the ABS light just switched on in dashboard n when I stop the car removed key n thn I started car it was gone I face same problem again this evening I tried all...

When youy start the vehcile the ABS goes through function test at above 10 MPH if there is a fault the light comes on, This can be a faulty sensor ,a faulty tone ring,or the harness connection.

Mar 25, 2012 | 1997 Nissan Skyline

1 Answer

My ABS light on my Isuzu trooper remain on how can I reset

You first need to scan your Antilock Brake System (ABS) computer to retrieve the fault codes set by the system failure. The fault codes are needed to identify the correct diagnostic and service procedure to repair the broblem with your ABS system. It will do absolutely no good to reset the computer memory to turn the light out if the system failure is not properly diagnosed and repaired. This will only result in the light coming back on again.

Feb 17, 2012 | 2002 Isuzu Trooper

1 Answer

2000 nissan exterra..the abs light is on

What is the question?

Same as any light you get on the
dash of any vehicle

Yours is an ABS System fault code,
possibly as Wheel Speed sensor

You always have to have the car checked
for codes,diagnosed and repaired,no matter
what light you get

Mar 18, 2011 | Nissan Xterra Cars & Trucks

1 Answer

1996 eldorado ABS light keeps comin on and off

You will need to get the abs codes to diagnose what is causing the light to come on.Once the codes are obtained then weather it is a speed sensor or the wiring that is causing your problem.Post back with the codes and I can help you with the repair.Good luck.

Dec 16, 2009 | 1996 Cadillac Eldorado

1 Answer

Nissan skyline 1996 broken wiring leading to the right hand indicator looks like it has been pulled apart recklessly .,,,looks like there is only three wires to the lite is this right if so what would the...

You can splice the broken wires back together, just make sure you get the colors right (red to red, yellow to yellow, etc). After you reattach the wires it would be best to use a soldering gun and solder on the repair, and wrap it with electrical tape.

Sep 19, 2009 | Nissan Stanza Cars & Trucks

1 Answer

Nissan r33 skyline coupe

i found out by going down to repco and buying an alsortment of bulbs then found out which was right when un did the front kit light

Jun 14, 2008 | 1996 Nissan 200SX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

77202 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides