Question about 1993 Jeep Grand Cherokee

2 Answers

Brake caliper removal

Any one able to help in removing brake calipers on 2000 jeppp GC

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

Check this guide tex, maybe can help you...
Replace Your Brake PadsGood luck!!!

Posted on Sep 10, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

BUY A BOOK AND C CLAMP AND SOCKET SET

Posted on Aug 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing break pads on 2000 tarus


Remove & Replace the Brake Pads
  • Loosen lug nuts from the front wheels with the ratchet and socket, but do not remove them.
  • Raise the front of the vehicle using the floor jack and secure it with jack stands.
  • Remove the lug nuts from the wheels and pull the wheels from the vehicle.
  • Look on the rear of the brake caliper and locate the caliper bolts, one upper and one lower.
  • Loosen and remove the upper and lower caliper bolts using the ratchet and socket.
  • Pull the caliper from the brake assembly, exposing the brake pads, and hang the caliper from a suspension component, using the bungee strap. Do not allow the caliper to hang by its hose, as this may cause damage.
  • Grasp the inner and outer brake pads and pull them from the brake assembly. Take note of how they were positioned, as the new brake pads must be placed in the same fashion.
  • Place the new brake pads on the brake assembly in the same position the old ones were.
  • Position the c-clamp over the caliper so the screw portion is contacting the the caliper's piston--the metal cylindrical object inside the caliper--and the fixed portion of the clamp is contacting the rear of the caliper.
  • Tighten the c-clamp until the caliper's piston is fully pressed into the calipers body. The top of the piston is even with the caliper body when fully pressed in.
  • Loosen the c-clamp and remove it from the caliper.
  • Place the caliper over the new brake pads and hand-tighten the upper and lower caliper bolts.
  • Tighten the upper and lower caliper bolts to 26-foot pounds, using the torque wrench and a socket.
  • Repeat Steps 4 through 13 for the brake pads on the other side of the vehicle.
  • Place the wheels back on the vehicle and hand-tighten the lug nuts.
  • Remove the jack stands from under the vehicle and gently lower it to the ground.
  • Tighten the lug nuts to 100-foot pounds using the torque wrench and a socket.
  • Press and release the brake pedal repeatedly until it feels firm.

Jan 09, 2012 | 2000 Ford Taurus

1 Answer

How can i compress the caliper piston back of audi a6 2000 2.8l awd what kind of tools i need . Vise grip is not working.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!

Check brake fluid level and top up if neccessary!!!

Oct 26, 2011 | 2000 Audi A6

1 Answer

Remving caliper pins on 2000 vw jetta and caliper


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Jun 26, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

1994 Jeep GC rear drum brakes grab on damp days and low speeds. All hardware has been replaced including new shoes and drums.


The Caliper Adjustment Lever is what adjusts the caliper - ensuring the brakes pads are in proper placement to the rotor for effective braking. The lever must be cycled in order to keep the calipers adjusted properly. The only way the lever is cycled, is by the usage of the e-brake.


zjlimited_1187.jpg

Remove the cable from the Caliper Lever. Be careful when handling and removing the spring.

zjlimited_1188.jpg

The Caliper Adjustment Lever is what adjusts the caliper - ensuring the brakes pads are in proper placement to the rotor for effective braking. The lever must be cycled in order to keep the calipers adjusted properly. The only way the lever is cycled, is by the usage of the e-brake.



Initial testing: After you have removed the ebrake cable - kneel in front of the rotor and give it a gentle shake (as if you were removing it). Do you notice any PLAY between the pads & rotor?? Make note of this.



For the TSM kit caliper adjustment instructions - visit here: Troubleshooting.htm#2 and click on "Adjust Caliper Parking Brake".

Good luck.

May 05, 2011 | 1994 Jeep Grand Cherokee

1 Answer

I'm changing the rear brakes on my 2000 Chrysler Concorde 2.7L V6 DOHC--removed the caliper and brake pads but not sure how to remove the rotor? Can anyone help?


If the caliper is loose after taking off the caliper then all you gotta do is remove the caliper housing. The part the caliper is bolted to. It's usually two big 16 or 17 mm bolts.

Mar 17, 2010 | 2000 Chrysler Concorde

1 Answer

How to insall front brake pads on a 2000 Ford Focus


caliper bolts are 7 mm Torx head.

SECTION 206-03: Front Disc Brake 2000 Focus Workshop Manual
REMOVAL AND INSTALLATION Brake Pads Removal
syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If brake fluid is spilt on the paintwork, the affected area must be immediately washed down with cold water.
  1. Loosen the wheel nuts.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel.
  1. Detach the brake hose from the support bracket.
  1. Detach the outer brake pad retaining clip.
  1. NOTE: Pull the caliper outwards to release the piston.
    Detach the caliper.
    1. Remove the bolt covers.
    1. Remove the bolts.
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Suspend the caliper to prevent load being placed on the brake hose.
    Support the brake calipers.
  1. Lift the outer pad retaining clip over the spring retaining lugs.
  1. Remove the outer brake pad.
  1. Remove the inner brake pad.
Installation
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If the caliper piston is retracted into the housing, brake fluid will be displaced from the master cylinder.
    Fully retract the caliper piston.
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
    Install the inner brake pad.
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
    Install the outer brake pad.
  1. Push the outer retaining clip over the spring retaining lugs.
  1. Install the caliper.
    1. Install the bolts.
    1. Install the bolt covers.
  1. Install the brake hose onto the support bracket.
  1. Locate the outer pad retaining clip.
  1. Install the wheels.
  1. Check the fluid level in the brake fluid reservoir.

Jan 18, 2010 | 2000 Ford Focus

3 Answers

How do i remove the rear rotor on a 2000 ford explorer xlt


  1. Disconnect the brake hose.
  2. Remove bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  5. Disconnect the brake hose.
    1. Remove bolt.
    1. Disconnect the rear wheel brake hose (2A442).
    1. Remove the copper washers and plug the brake hose.
      syn~us~en~file=dh0472a.gif~gen~ref.gif
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
      Remove the rear disc brake caliper (2552).
      1. Remove the brake caliper bolts (2W303).
      1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
      syn~us~en~file=gh0619a.gif~gen~ref.gif
    1. Inspect the rear disc brake caliper for leaks.
      • If leaks are found, disassembly is required. Refer to Caliper in this section.
      syn~us~en~file=gh1478a.gif~gen~ref.gif
    Installation
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
      NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
      NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
      Install the rear disc brake caliper.
      syn~us~en~file=dh0528a.gif~gen~ref.gif
    1. Install the rear wheel brake hose.
      • Connect the brake hose and install the caliper flow bolt.
        • Use new copper washers.
      syn~us~en~file=gh0621a.gif~gen~ref.gif
    1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
    1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
      Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
    1. Verify correct brake operation.
  6. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
--------------------------------
Installation
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
    Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

May 06, 2009 | 2000 Ford Explorer

1 Answer

Brake caliper removal


you can see 2 bolts at the back of caliper look the same ,one on the up ,and one at down,so just remove the bolt and put back the piston then you can put new pad on

Apr 12, 2009 | 2000 Toyota ECHO

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

How to change front break pads A4 2000 and what type/ make of pads do i need


I have the same car 2000 Audi A4. I recommend you "TRW" brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!! Please Rate my Response! Thanks!

Mar 02, 2009 | 2000 Audi A4

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...