At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
To remove the rear bumper cover on a 2008 Nissan Quest, you can follow these general steps:
Prepare the Vehicle: Ensure that the vehicle is parked on a flat surface and the engine is turned off. Put on safety goggles and gloves to protect yourself during the removal process.
Locate the Fasteners: Look for the fasteners securing the rear bumper cover. They are typically located underneath the bumper cover, near the wheel wells, and along the bottom edge of the bumper.
Remove the Fasteners: Depending on the specific model and trim level, the fasteners may be screws, bolts, or plastic clips. Use the appropriate tools, such as a screwdriver or socket wrench, to remove the fasteners one by one. Turn them counterclockwise to loosen and remove them. Keep the fasteners in a safe place for reinstallation later.
Disconnect Electrical Connections (if applicable): If your Nissan Quest has any electrical connections, such as sensors or lighting, attached to the rear bumper cover, disconnect them carefully. Look for connectors near the edges or inside the trunk area. Gently detach the connectors by pressing the release tabs or using a flat-head screwdriver to release any locking mechanisms.
Release the Clips: Once the fasteners are removed, there may be plastic clips or tabs securing the bumper cover to the vehicle's body. Carefully pry or release these clips using a trim removal tool or a flat-head screwdriver. Take care not to damage the bumper cover or the vehicle's body.
Remove the Bumper Cover: With all the fasteners and clips released, gently pull or wiggle the rear bumper cover away from the vehicle's body. Start from one side and work your way to the other, ensuring that all connections and clips have been detached. Be cautious of any remaining electrical connections as you remove the bumper cover completely.
Please note that the exact steps and fastener locations may vary slightly depending on the specific trim level and optional features of your 2008 Nissan Quest. It's always recommended to consult the vehicle's owner's manual or a professional technician for more precise instructions tailored to your vehicle.
Take your time during the removal process to avoid any damage to the bumper cover or the vehicle's body. If you're unsure or uncomfortable performing the removal yourself, it's best to seek assistance from a qualified technician or a reputable automotive service center.
Pop the Hatchback open and remove the connectors
from the top of the bumper cover.
Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.
Using Torx Bits, remove the inner rear wheel well
lining.
Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.
Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.
Not sure about Veracruz, but most of modern cars have the harness pre-installed to have additional factory things fitted, my Trajet had a plug behind the bumper, my Mazda had a plug for fog light just above the front wheel behind a cover. So I presume that your vehicle will have the same.
the best thing for you to do is stop by your Hyundai dealership in the parts department and they be able to print you off pictures and diagrams showing you how many there is and how it comes a part.
Pop the Hatchback open and remove the connectors from the top of the bumper cover.
Optional Step: Using a Floor Jack, raise both sides of the car in the back, supporting both sides with jack stands, and remove the rear wheels.
Using Torx Bits, remove the inner rear wheel well lining.
Get behind the rear wheel well and loosen the bolts holding the bumper brackets on. They're pretty difficult to find and remove. Be Patient. Do the same to the other side.
Remove the rear bumper cover by pulling the cover outward from the part nearest the wheel on both sides. Once removed, take off the 2 black mounting brackets from the bumper cover.
There is one reservoir for both the front and back windshield washers and it is located under the hood up by the passenger side headlight. Check out many diy repair articles on the 2005 Hyundai Accent at shareyourrepair.com
×