Question about 1995 Oldsmobile Cutlass Ciera

1 Answer

How to change tension adjust arm for Serpentine Belt

How do I remove and replace the tension adjust ment arm

Posted by on

  • Anonymous Mar 13, 2014

    belt tensioner replace ment

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 89 Answers

Reomve belt then the tensior arm is bolted to block i think its just two bolts if i remember right then bolt new on and replace belt hope this helps

Posted on Aug 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and replace a serpentine belt 96 saturn


Click on the following free, direct Link. It has all the Serpentine Belt Diagrams you will need for the 1.9L 4-Cylinder Engine and various Engine Options (AC/No AC etc.), complete with Instructional and Directional Diagrams.

http://www.2carpros.com/car_repair_information/year/1996/make/saturn/model/sl/1996_saturn_sl_drive_belt_routing_diagram.htm

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Apr 04, 2010 | 1996 Saturn SL

1 Answer

Tension pulley for serpentine belt making noise


The Tensioner Pulley Bearings are failing and either the Tensioner Pulley or the Tensioner Assembly (Pulley, Arm and Base) must be removed and replaced.

Click on the following free direct Link. It has several of the Serpentine Belt Diagrams and Tensioners that are possible with your 4.3L V6 engine.
http://www.2carpros.com/car_repair_information/year/1998/make/gmc/model/jimmy/1998_gmc_jimmy_drive_belt_routing_diagram.htm
1. Remove the Serpentine Belt.
"HOW TO":
Standard Rules to Removal the Serpentine Belt with a Tensioner:
A. Find the Tensioner(s). (See Diagrams on Link)
B. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
C. Remove the loosened belt off one of the other more easily accessed Pulleys.
D. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Removing the Tensioner Pulley: See the Diagrams in the Link.
After the Belt has been removed, with the Tensioner resting:
DEPENDING ON WHAT TYPE TENSIONER:
IF the Tensioner Pulley itself HAS a Bolt Head showing, SOME of these bolts can be removed and the Tensioner Pulley replaced.
IF the Tensioner Pulley itself DOES NOT HAVE a Bolt Head showing, then go to the Tensioner Base located at the end of the Tensioner Arm. This should have a Bolt Head Showing. Remove this Bolt and the whole Tensioner Assembly will com off.

When replacing the Tensioner Assembly - MAKE SURE you place the protruding "nipple" on the underside base of the Tesnioner into the appropriate cavity on the engine face.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Mar 29, 2010 | 1998 GMC Jimmy

2 Answers

How do you change the serpentine belt chevy malibu 200


Well you don't have to remove the tensioner. If you look at it, you'll see a 3/8 square hole in the arm of the tensioner. Put a ratchet wrench, or breaker bar in the hole, and you can move the tensioner, it is only spring loaded. The diagram for how the belt laces in should be on the radiator core support. Lace it for the majority around, move the tensioner, and once you have the belt in line, release the tension on the tensioner arm.

Mar 26, 2010 | 2000 Chevrolet Malibu

1 Answer

How do you tighten a loose serp. belt for 1997 mercury cougar xr7


There is no adjustment on the serpentine belt. I'm assuming that you have a 4.6 since it's an XR7. There is a spring loaded tensioner that keeps the belt in proper adjustment. The tensioner may be bad, or just corroded in one position. If there's no diagram for the belt routing under the hood...draw one. Then remove the belt and carefully persuade the tensioner to move. Careful not to break it or it's mount. If it doesn't move, it's going to need replacing. It's the one on the little arm, the arm should move.

Mar 20, 2010 | 1997 Mercury Cougar XR7

1 Answer

How do you replace the serpentine belt tensioner on 1990 sunbird 2.0 ohc


Click on the following free direct Link. It has several of the Serpentine Belt Diagrams and Tensioners that are possible with your 2.0L 4-Cylinder engine and engine options (AC/No AC, etc.).

http://www.2carpros.com/car_repair_information/year/1990/make/pontiac/model/sunbird/1990_pontiac_sunbird_drive_belt_routing_diagram.htm

A. Remove the Serpentine Belt.
"HOW TO":
Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

B. Remove the Tensioner:
Removing the Tensioner Pulley: See the Diagrams in the Link.
After the Belt has been removed, with the Tensioner resting:

DEPENDING ON WHAT TYPE TENSIONER:
(1.) IF the Tensioner Pulley itself HAS a Bolt Head showing, SOME of these bolts can be removed and the Tensioner Pulley replaced.
(2.) IF the Tensioner Pulley itself DOES NOT HAVE a Bolt Head showing, then go to the Tensioner Base located at the end of the Tensioner Arm. This should have a Bolt Head Showing. Remove this Bolt and the whole Tensioner Assembly will come off.
(3.) Some Tensioner Assembly's need you to locate and remove mounting bolts.

If Applicable: When replacing the Tensioner Assembly - MAKE SURE you place the protruding "nipple" on the underside base of the Tensioner into the appropriate cavity on the engine face.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them


Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Mar 13, 2010 | 1990 Pontiac Sunbird

1 Answer

SERPENTINE BELT REPLACEMENT


The Belt Diagram should be on the underside of your hood, however they have a way of disappearing.

If it is not there:

Click on the following free direct Link. It has the correct Serpentine Belt Diagrams for your 2001 Toyota Corolla 1.8L (4-Cylinder) Engine and Engine Options (AC/No AC etc.). Included are Instructional and Directional Diagrams for your use.

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2001/make/toyota/model/corolla/2001_toyota_corolla_drive_belt_routing_diagram.htm "HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Feb 14, 2010 | 2001 Toyota Corolla

1 Answer

Change power steering belts


My sincere apologies for the severly delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it in case you still do.

Click on the following direct Link. It has several Diagrams for your Belt depending on your engine size and options (AC/No AC etc.) AND whether you have Tensioners OR Locking/Adjusting Bolts/Nuts.
IF APPLICABLE: These point out the direction of rotation for the Tensioner in order to loosen and reinstall the Belt.

IF APPLICABLE: These also point out where the Locking and Adjusting Bolts/Nuts are, to loosen the belt and remove; and reinstall the Belt and .

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating it\moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.


Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/2003/make/mitsubishi/model/galant/2003_mitsubishi_galant_drive_belt_routing_diagram.htm

Dec 26, 2009 | 2003 Mitsubishi Galant

1 Answer

I need to replace the idler pulley/tensioner and the belt


When this idler wears out it makes a growling noise that changes with engine RPM. A Bad Idler Pulley May Wobble & Wear Out Your Serpentine Belt Prematurely. Get Rid Of That Horrible Noise & Change.

Remove the serpentine belt by using a breakover bar, ratcher or serpentine belt removal tool with the correct size socket for the pulley mounting bolt. Rotate tensioner arm to release tension. Remove the bel. Using the proper size socket, remove the tensiones mounting bolt and remove tensioner.

Before installing the new tensioner, make sure the mounting surface for the tensiones is clean and free rust or other obstructions. Find the locator pin hole and rotate the replacement tensiones until the locator pin and the hole line uo. Insert the pin into the hole. Reinstall the mounting bilt and torque down to tight fit.

Rotate the tensioner arm to install the serpentine belt. Make sure the belt is correctly fitted to all pulley in the drive system. Start the engine to check for any problems. Extreme care should be taken when reinstalling the serpentine belt because some of the pulleys are located in remote positions ans it is very hard to see that belt is seated properly in all of the grooves. If the belt isn't seated properly, the belt can "ride out" of the grooves and the belt can be damaged.

Also must review the ZJ Repair Manual Secc-7-Cooling-System for graphics references.

Hope helped with this. Remember rated this help. Good luck.

Nov 26, 2009 | 1996 Jeep Grand Cherokee

2 Answers

HOW DO I REPLACE THE SERPENTINE BELT ON MY 2.8 V6?


joecoolvette must not ever been near an A4 Audi. Although his outline of the serpentine belt change is correct, you can't get to on an A4. Check out AudiWorld Tech Articles, Chris Hansen has a nice post there on Serpentine Belt Tensioner Replacement that would address most of this question.

Aug 16, 2009 | 1998 Audi A4

1 Answer

Replacing serpentine belt, does the arm thats attached to the tension have to be removed?


To release the tension on the adjuster requires a wrench on the wheel bolt or there is a 3/8 square hole near the wheel that can take a 3/8 rachet.

Apr 26, 2009 | 2000 Ford Contour

Not finding what you are looking for?
1995 Oldsmobile Cutlass Ciera Logo

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...