Question about 1996 Isuzu Rodeo

1 Answer

Clutch My clutch feels like its stuck. It did this to me in March, not being able to afford a new clutch I just made it work. Then all the sudden in May, the clutch all the sudden works PERFECT and so I thought maybe there was just air in the line. Now all the sudden it has started doing it again. It feels as if the clutch is stuck and I can't get anything. Please help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 71 Answers

Id say its your clutch master cylinder....its failing to pump the fluild from the pedal to operate the clutch

Posted on Aug 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I installed a complete clutch & Flywheel. I popped outta 1st gear & won't go into any gear whatsoever. Linkage & slave cylinder work! feels like it's going into gear but when i let clutch out nothing


Isolate the problem. Sound like clutch is stuck and not disengaging. Engine off put in gear and rock the vehicle,, with help from a friend press clutch pedal while in gear and have friend push, you will know if the tranny is ok and clutch is stuck. Now check the clutch, slave etc for engagment and disengagment / Clutch linkage- movement/travel may need adjustment or you have something wrong in the reassembly..

Feb 08, 2016 | Cars & Trucks

2 Answers

2001 Camry 5 speed. It starts but it will not move. I can change gears without pushing in clutch. One mechanic said it was clutch and a different one said transmission is out. Which is it?


The clutch is not transferring power to the gearbox, which then is not turning, so that you can select gears without the clutch.Possibilities are
- clutch assembly has failed, possibly by the splined driven plate hub coming adrift
- clutch driven plate has become very worn and has lost contact
- slave cylinder has stuck through corrosion (assuming a hydraulic clutch) and is holding out the clutch independent of the pedal. This can be determined by watching it while someone depresses and raises the pedal.

I think it is unlikely the transmission input shaft has fractured.

Aug 14, 2015 | 2001 Toyota Camry

1 Answer

Replace clutch


A new clutch kit or clutch package has 3 major parts: a new clutch disc (the thin plate with the abrasive surface), a new or reconditioned clutch pressure plate, and a new clutch release bearing (aka, throw-out bearing). Approximately $200 for the package.
Some people have been known to change only the clutch disc (for about $30), and use their old pressure plate and throw-out bearing. Not recommended-same people have been known to have to go back sooner than later to then replace the pressure plate and release bearing. Do it all once, then you won't have to go back and re-do it.

Have you checked the hydraulic clutch operation? Before condemning the clutch disc for failure, make sure the hydraulic clutch cylinder causes the clutch fork or lever to have sufficient travel to engage the clutch when the pedal is depressed. Also check the clutch fluid reservoir for being full.

Sep 18, 2013 | 2006 Kia Spectra

1 Answer

2005 Subaru Forester brakes feel stuck "on"


They may be if it sat too long you could have corrosion build up which will go away, Check your E brake and cable, it may need adjustments or was not replaced correctly during the clutch job

Jul 02, 2013 | 2005 Chrysler 300

1 Answer

Wont go into any gear after installing a new clutch kit


Either it was not installed properly or... your clutch linkage (cable) is stuck or too tight and not releasing the clutch all of the way.


Disconnect the clutch cable/rod from the clutch arm and see if you can move it or if when you remove it does it goes back further with the spring i.e. not seated with the linkage in place...? (you should feel the spring action of the clutch on the plate)
if it does spring back further the cable/rod linkage needs to be adjusted
Otherwise take it apart and reinstall. Also check the clutch pedal to make sure it did not become misalligned while it was diconnected.

Apr 08, 2012 | 1998 Nissan Sentra

1 Answer

Bought this 2001 honda S2000 in march had a blown engine replaced the crank shaft and the clutch. New clutch went out in less than three weeks. Had car back now for 5 weeks and clutch just went out again....


I know it is not you.
It is most certainly, the folks doing the work on your vehicle,that is a fact.
What work,in detail, is being done,and by whom?
You surely must find this incompetent at best.

Iam praying it not a dealer,I dislike them,but would expect, they could handle a clutch service.

Sep 18, 2010 | 2001 Honda S2000

1 Answer

1999 carrera c2 feels like my clutch is slipping.


On the old 911's you could adjust the clutch. The new ones are hydraulic and self adjusting. Sounds like you need a new clutch.

Jan 05, 2010 | 1999 Porsche 911 Carrera

2 Answers

Nissan Sentra won't move.


Most likly needs a new clutch. but before you do that make shore the clutch slave cylinder is releasing.Do this by opening the bleed screw on the clutch slave cylinder. If there is preasure released when you do his you may have a stuck master cylinder. Not likly but worth the trouble to try

Jun 29, 2009 | 2001 Nissan Sentra

2 Answers

Toyota supra turbo 1990, manual (7mgte engine) Clutch problem


you need to bleed the clutch system.. have someone pump the clutch pedal three or four times, hold it down and release the bleeder valve( make sure the person holds the pedal down till after you tighten the bleeder valve back down) repeat this four or five times or till the clutch pedal feels like it did before.. good luck keith...

Mar 21, 2009 | 1990 Toyota Supra

1 Answer

The clutch wont engage on my 96 saturn


Your hydraulic clutch release has failed, it consists of a master cylinder and a slave cylinder, they will both have to be replaced.

Dec 17, 2008 | 2004 Saturn VUE

Not finding what you are looking for?
1996 Isuzu Rodeo Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...