Question about 2003 Mitsubishi Lancer

3 Answers

Replacing front wheel bearing

Just wanting to know how difficult it is and if any special tools are required to change the front wheel berings on my 2003 mitsubishi lancer

Posted by on

  • 1 more comment 
  • Anonymous Aug 29, 2008

    how do you get the bearings out?

  • Anonymous Nov 21, 2008

    I have the same problem and can anyone tell us how to replace it and is there any special tools needed for the work?

  • george boren Oct 21, 2012

    have a set of mm wrenches and sockets

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Posted on Aug 28, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When removing the old hub do i have to relese the struts ? what is the proper procedure when removing front wheel hub on 2004 mitsubishi Lancer

Posted on Feb 15, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have Datsun 100A car.I need to change front wheel bearing,where I get it and what is the number of the bearing for replacement

Posted on Sep 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

WHAT IF ANY SPECIAL TOOLS ARE NEEDED TO REPLACE A REAR WHEEL BEARING ?


No.
The most you'll need is a big hammer or a air hammer to loosen the bearing from the spindle but just like changing a front bearing

Jul 14, 2014 | 2006 Chevrolet Impala

1 Answer

REPAIR FRONT BERING ON A 2008 AVEOLS


Many special tools are required to do this and they cost allot of money. So take it to a shop is my advice.
Special Tools Required
  • 500-20 Hex Nut
  • J 36661-2 Forcing Screw
  • J 37105-1 Support Bridge
  • J 37105-2 Bearing Adapter
  • J 37105-3 Hub Adapter


Read more: How do I change the front wheel bearing on a 2007 Chevy Aveo - JustAnswer http://www.justanswer.com/chevy/216hr-change-front-wheel-bearing-2007-chevy.html#ixzz2AncxGv7c

Oct 30, 2012 | Chevrolet Aveo Cars & Trucks

1 Answer

Hyundia matrix 1.6 is it hard to change a drivers side ball joint ?


It is very difficult and requires special tools and skills, you will also need to have the front end aligned after the part change.

Jan 16, 2012 | Cars & Trucks

1 Answer

FRONT WHEEL BEARING ON 2005 MAZDA 3 ARE THEY PRESSED IN?


2005 mazda 3 front wheel bering left side are they pressed in and tools needed 2 replace bering

Sep 05, 2010 | 2005 Mazda 3

1 Answer

Repair front wheel bearing assembly


no special tools in particular just the usual or necessary tools required.. 1stly u remove the Tyre and the caliper then u'll see something like a long rod dats the bearing

Aug 02, 2010 | 2004 Mercury Mountaineer

2 Answers

Noisy front wheel bearing I would like to rerplace


a hydraulic press ,or go to a recon shop ,i was knocking one out and a splinter hit my mates eye ,nearly lost his eye ,HAVE THEM PRESSED IN AND OUT

Sep 20, 2009 | 2000 Ford Windstar

1 Answer

Front brake rotor removal


Your rotors have an integrated hub with serviceable bearing.

Remove the six bolts around the center of the hub and pry off the grease cover.

behind it you will find a locking wheel with two philips screws holding it in position. Remove the screws and unscrew the locking wheel.

Behind is a large axle locknut that requires a special tool to remove. It has two small holes to grip with. Unscrew it and you will be able to remove the outer bearing, then slide the rotor off the spindle/axle.

From there you can unbolt the rotor disc from the hub backside, or replace the whole unit. Replacing the whole unit will require installing new bearings/races, however.

Either method will require repacking the bearings and loading the bearings with the special locknut tool.

May 11, 2009 | 2000 Mitsubishi Montero Sport

1 Answer

How to replace front wheel bearings on 2000 Daewoo Lanos


they come as a whole assembly hub and all

Feb 15, 2009 | 2000 Daewoo Lanos

1 Answer

Front wheel bearng replacement


hi i am rather family with this type of jag and the wheel bearings can be a bit tricky and you was right special tools to do the job are reqiered my advice is let a proffesional mechanic do the job it will save you a lot of hastle

dean

Sep 10, 2008 | 1998 Jaguar XJ8L

1 Answer

Inner wheel bearing


The inner wheel bering is held in with a plate that is screwed in. no special tool is needed. You must remove the bearing housing from the brake disk. It took me 1.5 hours to do both sides.

Jul 02, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

2,473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...