1998 GMC Jimmy. My high beams are always on. It does matter if you turn them on manual or with the key (DRL). This started after replaced the turn signal switck. I checked the H/L switck and it's working right. Where is the DRL Module located and is there a way to test it?

is it so hard to tell your country or where it was first sold???

got DRL?
daylight running lamps. Yes/NO?
you known it but did not say.or bought a dead car like this>?

is this USA CAR or canada car , not told up north is DRL land.
not here. (rare and ended 2010 laws make it not mandatory USA)_
So we defeat them here.
just buy and old car lie this failing
or just now failed,??? so blinder and head lamps fail
well fuses are first, check the fuses, all of them.
GOT THIS.
GAUGE FUSE AND DRL FUSE MUST BE GOOD FOR DRL MODULE TO WORK


AND THIS
™ Lighting Control Module by ACDelco®. Designed utilizing the latest technology, this product by ACDelco features premium quality and will perform better than... more details on - https://www.carid.com/1995-gmc-jimmy-light-relays-sensors-control-modules/

It's probably the switch , but testing to know for sure is alwasy a good idea .

Headlamps Inoperative - High Beams
Step
Action
Value(s)
Yes
No
1
Did you perform the Daytime Running Lamps (DRL) System Check?
--
YES - Go to Step 2
NO - Go to Daytime Running Lights (DRL) System Check
2
Disconnect the turn/hazard headlamp switch connector C1.
Connect a fused jumper between terminal B of the turn/hazard headlamp switch assembly harness connector C1 and ground.
Do the high beam headlamps operate?
--
YES - Go to Step 3
NO - Go to Step 4
3
Replace the turn/hazard headlamp switch assembly.
Did you complete the repair?
--
Go to Daytime Running Lights (DRL) System Check
--
4
Repair the open in CKT 1200 between the turn/hazard headlamp switch assembly. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?

Daytime Running Lights (DRL) System Check
Step
Action
Normal Result(s)
Abnormal Result(s)*
1
Turn the headlamp switch to the HEAD position.
Turn the headlamp dimmer switch to the LOW position.
The low beam headlamps are ON.
The high beam headlamps are OFF.
Headlamps Inoperative - Low Beams
2
Turn the headlamp switch to the HIGH position.
The high beam headlamps are ON.
The high beam indicator is ON.
The low beam headlamps are OFF.
Headlamps Inoperative - High Beams
3
Turn the headlamp switch OFF.
Turn the ignition to ON.
Disengage the parking brake.
The high beam headlamps come ON at a reduced intensity in approximately 30 seconds.
Daytime Running Lamps (DRL) Inoperative, Headlamp Switch Operates Normally
* Refer to the appropriate symptom diagnostic table for the applicable abnormal result.

check for broken ground wire or bulb filaments crossed in the fixture..

headlights control by headlamp driver module relay to the BCM and the light sensor on dash next to the winshield defrost vents.headlights also control by high beam relay.

[Information] For a 2002 Toyota Camry, the Daytime Running Lights (DRL) operate utilizing the High Beams (inner Lamps closer to the center of the vehicle front) at a reduced power.

[The troubleshooting process:] Review the Owner's Manual and ensure the test configuration matches the following criteria:
1. According to the 2002 Toyota Camry Owner's Manual (Check your Owners Manual):
"The DRL system will make your headlights come on at a reduced brightness when:
The light switch s in the "DRL" position.
The ignition is on with the engine running.
The headlight switch is off.
The parking brake is released."

2. Set the Test Conditions according to Step 1 above.

3. Check the headlight bulbs to ensure they are not burned out. If one burns out, there is a fair chance that the other would have burned out at the same time. Replace as necessary. In this case, if the high beams operate, the DRLs should also operate.
4. Test the system, ensuring the step 1 conditions are set. (Engine running, Multi-function Switch on Turn Signals in "DRL" position, headlight switch off (repeating what the manual says -- it should be obvious that in the "DRL" position, the headlight switch should be off / do not have the switch positioned to "High Beam"), and the Parking Brake "off").
5. If DRL lights do not work, check the engine compartment Fuse and Relay Box. there is a 5 Amp DRL fuse -- replace it with the spare. Test (step 4).
6. If it does not work, swap around or replace relays -- there are three (3). Any one of them could be bad (stuck or burned out). Test (step 4).
7. Other less likely possible issues could be that the Multi-function Switch is broken or a connection / wire is broken. [Beyond the scope of this process.]

My problem was that the test configuration did not have the engine running and parking brake off - Step 1. Problem solved with much thought, repetitive tests on the vehicle and going back to the basics -- what does the Owner's Manual say and where are the applicable fuses and relays located?

either the low beams are burned out ,or the dimmer switch is bad.

I've seen this problem many times and so far it's always been the headlight switch

The problem with the DRL issue describd in the above posts is the DRl module(it needs to be replaced). The buzzing relay and intermittent on/off of passenger side DRl are indicators that the module needs to be replaced.

just try this. I had the same problem here a while back. try clicking on the high beam lever. mine went bad and was stuck in between high and low beam and would not come unstuck. and it caused the headlights not to work...

Some time back I found some data on a similar website suggesting that the Day Light Running circuit board, just under the steering column, developed cracks in some of the soldered joints. Your high beams should also be affected with loss of day light running lights.
Resoldering repaired the continuity of the circuits. Ours is now working quite reliably. Some of the defective areas developed slight brownish discoloration, that's how I was told to recognise the areas to be resoldered. Hope this will help you solve your problem.