Question about 1993 Oldsmobile Cutlass Supreme

1 Answer

Found 2 pin orange/black connector on ~2" wire in rear driver's side engine compartment...

...Where does it go? (And could this be related to my rough running maybe vacuum leak problem?)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

The orange and black wire is it on the fire wall on passenger side in engine compartment? if is the case it is used for setting timing it's a shunt wire.

Posted on Aug 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft sensor on a 98 ford explorer 4.0


On overhead cam engine--top rear of engine--2 wire connector--wire colors--dark blue/orange--and gray/red------On overhead valve engine--top rear of engine--3 wire connector--wire colors--dark blue/orange--light blue/orange--black/white

Jul 06, 2014 | 1998 Ford Explorer

Tip

ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1996 Honda Civic This...


ALARM, CRUISE CONTROL, and STEREO Wiring Color Codes for 1996 Honda Civic

This FixYa Tip is for the purpose of installing an Alarm, Remote Starter, Cruise Control, and / or Car Stereo into the vehicle listed in the subject line.

The wires listed are the ones you will need to successfully complete the task.

Some vehicles require additional relays and / or modules to bypass factory security. If they are required - it will be in the NOTES section below the wiring colors.

The following FixYa TIP is good for all Honda Civics for the following production years:

1996


STEREO WIRING COLOR CHART:
Constant 12V+: Blue/White
Switched 12V+: Yellow/Red
Ground: Black
Illumination: Red/Black
Dimmer: n/a
Antenna: Driver's Pillar

Front Speakers:
Left Front (+) Blue
Left Front (-) Gray/Black
Right Front (+) Red/Green
Right Front (-) Brown/Black

Rear Speakers:
Left Rear (+) Blue/Yellow
Left Rear (-) Gray/White
Right Rear (+) Red/Yellow
Right Rear (-) Brown/White

NOTES: Retain Keyless entry with secondary Harness Listed Below
Additional Accessories:
Metra Brand Dash Kit: 89-30-7891 - 99-7891 - 99-7898
Metra Brand Wiring Harness: 70-1720 W/Keyless Entry # 70-1720T
Metra Brand Antenna Adapter: n/a




ALARM / REMOTE START WIRING CHART:
Constant 12V+: White - Ignition Switch Harness
Starter: Black/White - Ignition Switch Harness
Ignition: Black/Yellow - Ignition Switch Harness
Ignition 2: Yellow - Ignition Switch Harness
Accessory: White/Black - Ignition Switch Harness
Tach: Blue - Coil
Brake Switch: Green/White - Brake Switch
Trunk Pin: Blue/Black - (-) Driver's Kick Panel
Parking Lights: Red/Black - (+) Driver's Kick Panel
Head Lamp: Red/White (L) Red/Blue (R) - Steering Column
Hood Pin: n/a
Door Trigger: Light Green/Red - (-) Above Fuse Panel
Door Lock: Green/White - (-) 2 pin connector taped to blue connector behind fuse box
Door Unlock: Green/Orange - (-) Module Behind Radio
Horn: Grey - Steering Column or GREEN connector behind radio

NOTES: - none -



CRUISE CONTROL:
Constant 12V+: White - Ignition Switch Harness or Use Hot Side of Brake
Switched 12V+: Black/Yellow - Ignition Switch Harness
Ground: Use Chassis Near Cruise Control Module
Hot Side of Brake: n/a - Brake Switch
Cold Side of Brake: Green/White - Brake Switch
Tach: Blue - Coil
VSS Wire : Blue/White - Driver's Side Dash Footwell, Grey connector.


NOTES: PPM - 4000PPM
ROSTRA Control Arm # 250-3421/250-1483
ROSTRA Throttle Adapter #250-4249

Vehicles with Manual Transmission require Clutch Switch.
Some vehicles may require a speed signal generator and/or other parts/adapters not listed above.
Rostra® Cruise Control module switch settings may differ if you use a speed signal generator or magnets and a pick up coil.

Thanks for using FixYa!! Please see my other tips on GPS, Car Audio, Large Appliances, and more.

on Apr 03, 2010 | Honda Civic Cars & Trucks

1 Answer

2006 tacoma heat/air blower fuse location


Hello! Coil of Heater Relay is supplied through Fuse "IG1 2" (10A)...Located in the Drivers Side Box...Contacts of Relay are supplied through "Heater Fuse (50A)...Located in Engine Relay Box...Blower Motor has a 2 wire connector with wire colors: Black/Yellow (Pin 2)...And White/Blue (Pin 1)...Pin 1=Ground and Pin 2=Battery when Relay pulls and contacts close...
The Blower Resistor Pack (Which fails often) controls the fan speed...BUT, there is a fuse inside the assembly...If it blows = No Fan...Located on the top of the heater/AC box and can be accessed through the Glove Compartment...Guru...Saailer

Jun 01, 2012 | 2006 Toyota Tacoma

2 Answers

What or the color of the radio wires for in a 1993 bonneville


Use a multimeter to find the two feeds and then a 9v pp3 battery to check the speakers it thats simple .

Feb 25, 2012 | 1993 Pontiac Bonneville

1 Answer

My speed don't work


Speed Sensors REMOVAL & INSTALLATION Front Fig. 1: The speed sensor sits directly over the exciter ring in the front knuckle 89609p51.jpg
Fig. 2: Detach the speed sensor connector in the engine compartment 89609p55.jpg
Fig. 3: Remove the speed sensor harness from the routing clips 89609p53.jpg
Fig. 4: A special E6 Torx® socket is required to remove the speed sensor retaining bolt 89609p52.jpg
  1. Disconnect the negative battery cable.
  2. From inside engine compartment, detach sensor assembly 2-pin connector from the wiring harness.
  3. Remove the steel routing clip attaching the sensor wire to the tube bundle on the left sensor or remove the plastic routing clip attaching the sensor wire to the frame on the right sensor.
  4. Remove the rubber coated spring steel clip holding the sensor wire to the frame.
  5. Remove the sensor wire from the steel routing clip on the frame and from the dust shield.
  6. Remove the sensor attaching bolt from the front spindle and slide the sensor out of the mounting hole. To install:
  7. Install the sensor into the mounting hole in the front spindle and attach with the mounting bolt. Tighten to 40–60 inch lbs. (4.5–6.8 Nm).
  8. Insert the sensor routing grommets into the dust shield and steel bracket on the frame. Route the wire into the engine compartment.
  9. Install the rubber coated steel clip that holds the sensor wire to the frame into the hole in the frame.
  10. Install the steel clip that holds sensor wire to tube bundle on left side or plastic clip that holds sensor to frame on right side.
  11. Reconnect the 2-pin connector to wire harness. Connect the negative battery cable.
Rear Fig. 5: Detach the speed sensor connector in the luggage compartment 89609p04.jpg
Fig. 6: Grasp the harness and . . . 89609p37.jpg
Fig. 7: . . . remove it from the routing brackets 89609p36.jpg
Fig. 8: The rear speed sensor is mounted on the back of the hub assembly 89609p32.jpg
Fig. 9: Remove the sensor retaining bolt and remove the sensor from the hub 89609p34.jpg
  1. Disconnect the negative battery cable.
  2. From inside luggage compartment, detach 2-pin sensor connector from wiring harness and push sensor wire through hole in floor.
  3. From below vehicle, remove sensor wire from routing bracket located on top of rear axle carrier housing and remove steel clip holding sensor wire and brake tube against axle housing.
  4. Remove screw from clip holding sensor wire and brake tube to bracket on axle.
  5. Remove sensor to rear adapter retaining bolt and remove sensor. To install:
  6. Insert sensor adapter and install retaining bolt. Tighten to 40–60 inch lbs. (4.5–6.8 Nm).
  7. Attach the clip holding the sensor and brake tube to the bracket on the axle housing and secure with the retaining screw. Tighten the screw to 40–60 inch lbs. (4.5–6.8 Nm).
  8. Install steel clip around axle tube that holds sensor wire and brake tube against axle tube and push spool-shaped grommet into clip located on top of axle carrier housing.
  9. Push sensor wire connector up through hole in floor and seat large round grommet into hole.
  10. Reconnect sensor 2-pin connector to wiring harness inside luggage compartment.

Aug 03, 2010 | 1992 Ford Crown Victoria

1 Answer

Cant find the ineryia switch 1988 bronco2 looked on right side 2.9 injected


The inertia switch is by the passenger left foot, it has Pink/Black & Orange/Blue wires. It’s connector in the engine bay is a Black Rectangular 2-Pin. (Inertia switch connector pictured) 29-50_3.jpg

Mar 04, 2010 | 1988 Ford Bronco II

2 Answers

No power to the fuel pump


Once you check the fuel inertia switch in the passenger's side kick panel, next is to check the fuel pump fuse, engine compartment fuse # 10.

If this checks OK ( power on both sides ), you can pull the fuel pump relay, and jumper it.

The engine compartment fuse panel is where the fuel pump relay is located at ( relay # 301 ). Pull the fuse pump relay out of the socket, and using the diagram below, with the red line, momentarily jumper the Normally open contacts, you shoud hear the fuel pump run. ( mind the pin orientation when doing this ) :
86000f6.jpg

I had a bad fuel pump relay on my 2001 F-150 @ ~ 36K miles. Replaced with the trailer tow battery charge relay ( relay #302 next to it ) and it worked again.
The symptom I had was a crank no start ( theft light on dash went out ).

If the fuel pump does not run, and power is on pin #30 in the relay socket, next is to check the output of the fuel inertia switch in the passenger side kick panel. The output of this is the Pink w/ Black stripe wire. The connector to the fuel pump inertia switch should be a 2 pin connector, the other color in the connector is Dark green w/ Yellow stripe wire ( that is from the pin #87 in the relay socket in the engine compartment ).

If that circuit has power at the passenger side kick panel, next is to check for power at the fuel pump at the fuel tank. The fuel pump motor is the same Pink w/ Black stripe wire. The connector is a 4 pin connector with black ( ground for the fuel pump ) black w/ orange stripe ( ground for the fuel level ) and yellow w/ white stripe ( to the instrument cluster for the fuel gauge ).
When testing by the fuel tank, make sure you have a good ground for the meter ( extension from neg on the battery or trailer tow adapter ) as that could also be a problem under the truck.

Sorry for war and peace, hope it helps.

Nov 17, 2009 | 2001 Ford F150 Styleside SuperCrew

2 Answers

2002 jetta tdi died while shifting into 4th gear


Sorry, not a solution to this car but your other vw 1989 jetta...only way I could get hold of you.

here is your diagram

The following information covers electrical connections and plugs to the rear of the fuse/relay panel. It completes and supplements the information in the appropriate Service or Repair Manual for the fuse/relay panel section and should be used in conjunction with the wiring diagram for the vehicle or system in question. Volkswagen part numbers shown here may or may not match those on your panel, however, if you panel visually matches the diagram, it is correct for your application.
Fuse/Relay Panel - Rear Connections (Volkswagen Part Number 171 941 821 D) clear.gif
97-3228.gif
Connections and plugs on rear of fuse/relay panel:
A Blue 28 pin Instrument cluster wiring harness B Red 28 pin Instrument cluster wiring harness (position 5 open) C Yellow 22 pin Engine compartment/engine management, left side (position 10 open) D White 29 pin Engine compartment/wiper motor wiring harness, right side (position 6. 10, 14, 18, 27, 28 open) E Black 18 pin Rear wiring harness (position 17 open) G n/a 1 pin 10 individual circuits H Brown 6 pin Air conditioning/coolant fan relay wiring harness K Neutral 5 pin Seat belt warning system/coolant level wiring harness L Grey 4 pin Horn wiring harness L Black 4 pin Headlight/dimmer switch wiring harness M Black 2 pin Steering column switch wiring harness M Black 2 pin Headlight/dimmer switch wiring harness N Red 1 pin Separately fused circuits (glow plug wiring harness) P Red 7 pin 7 single point connectors for terminal 30 circuit R Green 2 pin Open/ECM power supply relay
Note: Terminal and harness assignments for individual connectors will vary depending on vehicle equipment level, model, and market. Always consult appropriate wiring diagram for specific terminal assignments.

hope this has resolved your problem

Thankyou

Aug 15, 2009 | 2003 Volkswagen Jetta TDI

2 Answers

Fuse box


Wiring relays and connections – all modelsRelays (typical)

1 Vacant
2 Intake manifold preheating relay (carburettor models) or fuel
pump relay (injection models)
3 Seat belt warning system relay
4 Gearshift indicator control unit
5 Air conditioner relay
6 Dual tone horn relay
7 Relay for foglights and rear foglight
8 Relief relay for X contact
10 Intermittent wash/wipe relay
11 Rear window wiper relay
12 Turn signal flasher or trailer towing warning relay
13 Seat belt warning system (interlock) or rear window, driving
lights and oil pressure warning relay
14 Window lift or seat belt warning system relay
15 Headlight washer relay
16 Control unit for idling speed increase
17 Fuse for rear foglight
18 Control unit for coolant shortage indicator
19 Thermo fuse for window lifters
20 Switch unit for heated driver’s seat
21 Switch unit for heated passenger’s seat
22 Switch unit for overrun cut-off
23 Vacant
24 Vacant
Relays are symbolised as a number in a black box
Not all relays are fitted to all models
Connections
A Multi-pin connector (blue) for dash panel loom
B Multi-pin connector (red) for dash panel loom
C Multi-pin connector (yellow) for engine compartment loom left
D Multi-pin connector (white) for engine compartment loom right
E Multi-pin connector (black) for rear wiring loom
G Single connector
H Multi-pin connector (brown) for air conditioner or wiring loom
K Multi-pin connector (transparent) for seat belt warning system
loom
L Multi-pin connector (black) for lighting switch terminal 56 and
dip and flasher switch terminal 56b (carburettor models) or
multi-pin connector (grey) for dual tone horn (injection models)
M Multi-pin connector (black) for lighting switch terminal 56 and
dip and flasher switch terminal 56b (injection models)
N Single connector for separate fuse (manifold heater element)
P Single connector (terminal 30)
R Not in use
Fuse colours
Blue 5A
Green 30A
Red 10A
Yellow 20A

Jul 17, 2008 | 1987 Volkswagen Jetta

Not finding what you are looking for?
1993 Oldsmobile Cutlass Supreme Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...