Question about Ford Explorer

1 Answer

Ford exployer 2000 4.0 eng my oil gauge works when it wants to is it the sending unit or the oil pump going

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Do a mechanical oil pressure test to confirm the operation of the oil pump and if its good change the OIL pressure sending unit

Posted on Aug 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pressure sending unit located in a '01 dodge dakota, 4.7 eng.?


go to CTC and buy a service manual for 2001 dodge Dakota 4.7 litre engine there will be 2 oil pressure sending units one that is for the gauges in the dash and the other for the oil pressure sending unit mounted on engine

Feb 12, 2015 | Dodge Cars & Trucks

2 Answers

How can i fix the oil pump


see this tips and fix it. God bless you
The oil pump supplies oil to lubricate your engine. If the oil pump is worn or is not turning, the engine will suffer a loss of oil pressure, which may result in engine damage or engine failure.
The first sign of trouble may be a low oil pressure warning light, a drop in the normal reading on you oil pressure gauge (if your car has one), or the appearance of ticking or clattering sounds from your engine.
As a rule, most engines only need about 10 PSI of oil pressure for every 1,000 RPM of engine speed. Oil pressure will read higher than normal when a cold engine is first started because the oil is thick. Oil pressure will gradually drop as the engine warms up and the oil thins out. So normal oil pressure on a warm engine cruising down the highway is typically 30 PSI up to 45 PSI.
SYMPTOMS OF OIL PUMP TROUBLE
The first thing you should do if any of these symptoms occur is to stop your car, turn off the engine, let it sit for a few minutes, then check the oil level on the dipstick. If the oil level is at or below the ADD line, add a quart of oil to bring the level back up to the full mark. Add as much oil as is needed to raise the level to the full mark. Then restart the engine. If the warning light remains on, or the oil pressure reading does not climb back up to its normal range, or the engine noise does not go away, you may have a bad oil pump.
The other possibilities include a bad oil pressure sending unit, or a problem with the oil pressure warning light circuit or oil pressure gauge.
OIL PRESSURE SENDING UNIT
If the engine is NOT making any unusual noises and seems to be running normally, and the oil level on the dipstick is FULL, but you are still getting a low oil pressure warning light or low gauge reading, the fault could be a bad oil pressure sending unit.
The oil pressure sending unit is mounted on the engine block. On some applications, there is a spring-loaded pressure-sensitive diaphragm with a switch inside the sending unit. This switch completes the circuit to the low oil pressure warning light if oil pressure drops below a certain threshold. The unit may stop working if the diaphragm inside fails, if the switch is stuck, if the small hole that allows oil to enter the sending unit becomes plugged, if there is a loose, corroded or broken wiring connector at the sending unit, or there is a fault in the wiring circuit between the sending unit and warming light.
On vehicles that have an oil pressure gauge (electronic, not mechanical), the oil pressure sending unit has a small rheostat inside that sends a variable voltage signal to the oil pressure gauge when the diaphragm moves. A worn spot on the rheostat or any of the other problems just described for the simple pressure-type oil pressure switches can cause a problem.
FORD'S FAKE OIL PRESSURE GAUGE
On many Ford vehicles that were built from 1980 through the 1990s, the oil pressure sending unit has two switches, a low pressure and a high pressure. These vehicles also have an oil pressure gauge, but the reading on the gauge is not a true indication of real oil pressure. As long as the pressure to the sending unit is between high and low, the gauge will read normal. If oil pressure drops and trips the low pressure switch, the dash gauge will now read low. Or, if oil pressure goes up and trips the high switch inside the sending unit, the dash gauge will read high. Consequently, don't rely on the oil pressure gauge for an accurate reading in these vehicles. It is only a gross indication if the oil pressure is low, normal or high.
OIL GAUGE PROBLEMS
If the engine is NOT making any unusual noises and seems to be running normally, the oil level on the dipstick is FULL, and you have replaced the oil pressure sending unit but are still getting a low oil pressure reading on the dash gauge, the fault could be in the wiring circuit between the sending unit and gauge, or the gauge itself might be bad.
Check the wiring connections on both ends as well as wiring continuity between the sending unit and gauge. If no wiring faults are found, hook up a pressure gauge directly to the oil pressure port on the engine and check oil pressure with the engine running. If the engine-mounted gauge shows normal oil pressure but the dash gauge is reading low, the problem is a bad dash gauge.
On the other hand, if the engine-mounted pressure gauge reads low and you have done all of the above, chances are the oil pump is worn, or it is not picking up enough oil because of a restriction or blockage in the pickup screen in the bottom of the crankcase.
OIL PUMP PICKUP PROBLEMS
The pickup tube has a screen on the end to prevent large chunks of anything bad that ends up in the crankcase from being sucked into the pump. But we are talking BIG chunks of debris, not normal wear particles or carbon or dust or other microscopic-sized abrasive particles that can cause pump wear over time.

Sep 28, 2012 | 1996 Toyota Tercel

1 Answer

I have a 2000 Ford Explorer Sport. After driving 15-20 minuets and coming to a stop the oil gauge fluctuates wildly. Sometimes the check engine light comes on. When I put the vehicle in park and give it a...


Sounds to me like it could be a bad oil sending unit or gauge. I would take it in to a shop and have them test the oil pressure with their equipment.
If they tell you the pressure is good try changing the oil sending unit first then if that don't work, replace the gauge.

Aug 26, 2010 | Ford Explorer Sport Cars & Trucks

1 Answer

2000 Ford F-150. The oil temp warning light came on and the oil pressure gauge dropped to zero. While accelerating, the pressure gauge goes back to normal and the warning light goes out. No drivability...


Make sure the oil level is correct. If the engine bearings are getting worn, the oil pump is worn or it's screen plugged, that can cause low-RPM weak oil pressure. Try running with 'high mileage' oil at your next oil change and always replace the filter. At some point, you may need to consider overhauling or replacing the engine. Good luck!

Jun 06, 2010 | 2000 Ford F150 Flareside SuperCab

1 Answer

Oil Pressure Dropped


The oil pressure sending unit is located at the front of
the engine near the power steering pump.
Hope this helps.

Mar 22, 2010 | 1999 Ford Explorer

2 Answers

Oil pressure loss


the 1st thing u do is have the oil pressure tested with a test mechanical gauge by a shop, most times it is just the oil pressure sending unit is defective, but never assume that is the problem, low oil pressure will distroy a $5000.00 engine very quickly, u can just try a new sending unit, but highly recommend a pressure test with a mechanical gauge before you run the engine anymore.

Dec 05, 2009 | 2000 Jeep Cherokee

1 Answer

Oil light blinks on and off could pressure switch be bad if so where is it located on a 2000 ford windstar 3.0


Oil Pressure Switch Operation:
00134_oil_pressure_switch_gauge.jpgInformation relay unit for the indicator light or gauge on instrument panel. It contains a diaphragm that responds to changes in oil pressure. When the oil level is over a pre-set limit, the diaphragm opens the switch, turning off the light. When level is below the pre-set limit, the dash light comes on. In later model cars, if the oil pressure drops, the switch turns off the fuel pump, to stop the engine and limit damage to internal parts. Oil pressure switches can be grouped into two categories, units for electrical gauges and for mechanical gauges.

Oil pressure can be checked at the sending unit passage with an externally mounted mechanical oil pressure gauge. To get accurate results from the test, make sure you follow the manufacturer's recommendations and compare your findings to specifications.
Testing the Oil Pressure Gauge
  • Test the gauge by grounding the wire that leads to the sending unit on the block.
  • When the wire is disconnected from the sending unit with the key switch on, the needle on the oil pressure gauge should be either all the way high or all the way low. Grounding the wire should make the needle move to the opposite side of the gauge from where it was before the wire was grounded. If the vehicle is equipped with an oil pressure light, touching the wire to ground and then removing the wire from ground should turn the light on and off.
  • If either happens, the gauge and wiring are good and the sending unit is at fault.
Testing Oil Pressure
Pressure can be tested by temporarily installing an oil pressure gauge in place of the sending unit. Before testing, look up the oil pressure specifications for your vehicle in the appropriate service manual.
  • Bring the engine up to operating temperature.
  • Now shut the engine off.
  • Locate the oil pressure sending unit; usually it is on the lower side of the engine block.
  • Disconnect the wire from the sending unit and use an open ended wrench to remove the sender. Using pliers can damage the unit.
f43-19.jpg An oil pressure sending unit is removed with a special socket. Courtesy of Chrysler Corporation.
  • Tighten the oil pressure test gauge into the hole in the block where the sender was removed.
f11-15_3184.gif Measuring oil pressure. Reprinted with permission.
  • Check the engine's oil level and fill, if required.
WARNING Be extremely careful when working near a running engine. Always wear safety goggles or glasses with side shields when working around moving machinery and be sure that your clothing is not loose.
  • Now turn the engine on and check the oil pressure on the gauge.
    • Watch as the engine warms to note any excessive drops due to temperature.
    • Make sure the engine speed is set to specifications for testing pressure.
    • If necessary, us a tachometer and adjust the engine idle speed.
  • Record the measured oil pressure, then turn off the engine.
  • Compare the test results with the manufacturer's specifications.
    • If the oil pressure is within specifications, this shows that the oil pressure sending unit may not be working correctly.
    • In many cases, replacing the oil sending unit will correct the problem.
  • After the test is complete, reinstall the oil pressure sending unit, start the engine, and confirm there are no leaks.




Nov 17, 2009 | 2000 Ford Windstar

2 Answers

Oil gauge won't stay up


It sounds like most likely its your Oil pump, if you have no pressure at stop and when you hit gas it sets the C/E light off, Guages in dash wont set off Check Engine Light. Replace Oil Pump.

Sep 03, 2009 | 2000 Jeep Cherokee

3 Answers

Oil pressure problem


You oil pressure sending unit has gone bad, it's common to go bad and some even leak oil. 
The oil pressure sensor is on the back of the block on the passenger side, you can get to it from the top and not from the bottom. There are (2) switches back there that screw in to the block and you can only see it from the top of the engine. The Oil Pressure Sending Unit is the one wire harness with a green and white strip on it. The other switch has more wires to it. 
When you pick up the new sensor, make sure you get the right one. make sure you get the Oil Pressure Sending Unit which sends variable oil pressure and has only one quick connect for the wire connector. The oil pressure switch is the one that only activates the oil light on older engine
Once you get the right part at Auto Zone for around $9.00, disconnect the wire clip with the green with white strip on it. and use a deep spark plug socket with a extension and u joint to get the sensor out. The sensor comes with teflon tape already and no oil should leak out from the block. It as simple as replacing a bolt and reconnecting the wire connector. 
Good luck and hope this helps, take no more then 10 min to do but about 5 hours for the engine to cool off LOL

May 29, 2009 | 2000 Ford Ranger SuperCab

1 Answer

Oil pressure gauge keeps fluxuating. Think it is the sensor. Want to know where the sensor is located on my 1994 lincoln continental


The oil sending unit is located below the power steering pump. 
You can get to it by removing the alternator, then the three bolts around the power steering pump bracket. Remove the small pulley on the bracket and pull back on the power steering bracket. Look behind bracket and you will see the oil sending unit. 

Disconnect the wire from the oil sending unit. Use a deep socket (1 1/16) to remove unit. 

While you have unit remove, I would go ahead and use an oil pressure gauge to test the oil pump pressure. 

Good luck and hope this helps

May 02, 2009 | Ford Lincoln Continental Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...