Question about 2003 Dodge Caravan

1 Answer

Radio and lighter wont work

My radio and lighter don't work, but uf i press the time button the time lights up than goes off after a second

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 182 Answers

Your fuse sounds like it has burned out. the radio and lighter are most likely on the same fuse.

Posted on Aug 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My radio/tape deck/CD player all of a sudden do not work, and only those items.


I would see the Audi dealer service department on this, I think the radio has failed.

Jul 18, 2016 | 1997 Toyota Avalon

Tip

Chevrolet service light 1991-01


Camaro

1998-01

To reset the "OIL CHANGE" light, press and hold the "TRIP/OIL RESET" button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset.


Corvette


1997-01

To reset the monitor after an oil change, turn the ignition on. Press the "TRIP" button so that the "OIL LIFE" percentage is displayed. Press "RESET" and hold it for two seconds. The word "RESET" should appear on the monitor, then "OIL LIFE 90%".


Impala,
Monte Carlo


2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator three times within five seconds. If the CHG OIL SOON lights two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not been reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to exit programming. A chime will be heard to verify the exit.


Impala,
Caprice


1994

To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Access the reset button on the end of the instrument panel by the fuse block. Press the switch and hold it for at least 5 seconds.



Lumina,
Monte Carlo,
Impala,
Caprice


1996-00,
1996-99,
1995-96,
1995-96

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds. The light will flash and go out.


Corvette


1990-96

After an oil change, or when "CHANGE OIL" appears on the Trip Monitor, with the ignition on and engine off, press the "ENG MET" button (located on trip monitor) once. Press the "ENG MET" button again within 5 seconds. Within 5 seconds, press and hold the "RANGE" button (1990-1994) or "GAUGES" button (1995). The light will flash. When it stops flashing and goes out, the system is reset.


Chevrolet Suburban,
GMC Yukon XL,
Chevrolet Silverado,
GMC Trucks Sierra


2000-01,
1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.


Silverado, Sierra Trucks


1991-93

To reset the "CHANGE ENGINE OIL" message, turn the ignition key to the run position. Press and release the accelerator pedal three times within 5 seconds. If the light flashes for 5 seconds, the system is reset. Repeat procedure as needed.















on Dec 07, 2009 | Chevrolet Camaro Cars & Trucks

1 Answer

I would like to know which buttons to push on my 2008 Chevy cobalts clock to set the time


Without Date Display
AM/FM Base Radio with a Single CD Player
This type of radio has a button for setting the time. You can set the time by following these steps:
Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press the knob, located in the center of the radio, to turn the radio on.
Press the button until the hour begins flashing on the display. Press the button a second time and the minute begins flashing on the display.
While either the hour or the minute numbers are flashing, turn the knob, located on the upper right side of the radio, clockwise or counterclockwise to increase or decrease the time.
Press the button again until the clock display stops flashing to set the currently displayed time; otherwise, the flashing stops after five seconds and the current time displayed is automatically set.
To change the time default setting from 12 hour to 24 hour, press the button and then the pushbutton located under the forward arrow label. Once the time 12H and 24H are displayed, press the pushbutton located under the desired option to select the default. Press the button again to apply the selected default, or let the screen time out.

With Date Display
Single CD (MP3) Player
This type of radio has a button for setting the time and date.
To set the time and date, follow these instructions:
Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press the knob, located in the center of the radio, to turn the radio on.
Press the button and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays.
Press the pushbutton located under any one of the labels that you want to change. Every time the pushbutton is pressed again, the time or the date if selected, increases by one.
• Another way to increase the time or date, is to press the right SEEK arrow or FWD button.
• To decrease the time or date, press the left SEEK arrow or REV button, or turn the knob, located on the upper right side of the radio.
The date does not automatically display. To see the date press the button while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display.

Hope this helps ! hope you had a very Merry Christmas an have Happy New Year

Dec 27, 2014 | 2008 Chevrolet Cobalt

3 Answers

Can someone tell me where i can locate cigarette lighter fuse in a toyota funcargo ncp20, i located 2 fuse boxes, 1 under the steering wheel, and other under the hood but on covers don't show a sign of...


put your low lights on,see if sigaret lighter lids up.
box under steeringwheel.take out one by one and see whit fuse,
light goes off.is also possible in the cover off the box is indicated whits one it is

Jul 07, 2013 | Cars & Trucks

1 Answer

My gear shifting lights and cig lighter don't work. Any lights on the Center console don't work. I checked the fuse box and they seem fine, although I cant find where those lights would be. ...


All I can say is that I think it may be a wire or wires in the dash area. Mine forces me to drive with a separate light to see speedometer. The radio goes on frequently and changes itself from cd to tape to radio. Driver heated seat no longer works. See if some of your lights work with the headlights off. Some of mine do. I have had mechanics look, but at $90 an hour, I pull em out after a few hours and no results...
Good luck!

Sep 29, 2011 | 2002 Hyundai XG350

2 Answers

Low tire pressure light wont go out


The Low Tire Pressure Indicator must be reset using the Radio. This can only be performed if you have the factory radio installed in the vehicle. This vehicle does not come with an active tire pressure management system, and as such, this light must be reset manually.
1.) Turn Radio Off 2.) Hold down disp button for 10 seconds 3.) Setup Menu should display 4.) Scroll through menu to view "Tire Pressure" (use seek buttons) 5.) Select the Tire Pressure option (Press Radio Button 1) 6.) Reset should be displayed on screen (Press disp button) 7.) Tire Pressure Light should reset

Nov 29, 2010 | 2000 Chevrolet Impala

1 Answer

The dome light in my 2000 kia sephia will not work nor will the lights on my radio. Where is the fuse to control these and are they both on the same fuse?


most the time the cigerette lighter fuse has blwon. that fuse goes for radio and probably int. light.some fuses feed other fuses so cig lighter fuse does not have a label that says radio. check all the fuses anytime you check for elect. problems

Mar 21, 2010 | 2000 Kia Sephia

2 Answers

I need to know how to set the time on the radio clock of 91 s10


It really depends on the type and model of your radio. Below is the generic clock set proceedure for the most popular radio at that time.
Hope this works for you.
Regards,

To set the clock, just:
Press the SET button. The word SET will light up in the VF display.
Within 5 seconds, press and hold the SEEK button until the correct hour
appears on the display.
Then, press and hold the SCAN button until the correct minute appears
After you set the time, the word SET will remain in the VF display for a
on the display.
few seconds.

Jun 18, 2009 | 1991 Chevrolet S-10

1 Answer

Radio wont work


wfdyer,

go buy a new radio. You can usually get free installation. If you are a do it yourselfer. Then go to crutchfields web site. They are great, they give you the adaptor plates and wire harness to go from what ever radio you get to the car, with no splicing (cutting and reconnecting of wires) They will tell you what radios will not work and tell you what ones will.

Sorry to say it but you have power to the radio, and there are really 3 things a radio needs to work. power, speakers, and a signal. you can check the antena to make sure its not broken or disconnected. but most of the times its the radio

tepfy

Jan 23, 2009 | 1997 Cadillac Catera

2 Answers

How do I turn off the change oil light on a 1994 corvette


1. Turn the key to “Run,” but don’t start
2. Press “ENG MET” on the Trip
the engine.
Monitor. Then, within five seconds,
press it again.
3. Within five seconds, press and hold
“GAUGES” on the Trip Monitor. The
“CHANGE OIL” light should flash.
4. Hold the “GAUGES” button until the
“CHANGE OIL” light stops flashing
and goes out. This should take about
ten seconds.
When the light goes out, the monitoirs
reset. If the monitor doesn’tr eset, turn the
ignition off, then try again.

Nov 18, 2008 | 1994 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...