Question about 1995 Isuzu Pickup

1 Answer

1992 isuzu pick up

Where is the turn signal flasher? I found the hazard flasher by listening to it tick but my turn signals are not working so i can't do the same for it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 182 Answers

It is usually near the hazard flasher an looks the same.

Posted on Aug 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left turn signal doesn't flash.


there is a flasher under the dash put your 4 ways on and listen for the tick noise find the flasher unit under dash area driver side there is two one for the 4 ways and 1 for turn signals now that you have found them turn on working signal touch the flasher unit you will feel it pulse and hear the noise when you have the one pulseing on working signal this will need replacing can also be in fuse area have a good day

Nov 22, 2014 | 1990 Buick LeSabre

1 Answer

Hasards dont come on on a 2000 isuzu trooper


No need to panic-this can SEEM TO be caused by a couple of things, but it is fairly simple to determine exactly what is causing this flasher circuit condition.
First, turn on your flashers, however you have to do it, and walk around the truck to check that all bulbs are working (at least one on each corner). Turn signal and hazard flasher relays are thermal circuit interrupters and are current sensitive and will not work properly with too few or too many bulbs in the circuit. (This is usually a big problem when switching over to LED lamps, as LEDs only draw a fraction of the current that the bulbs do. This causes the relay to either not flash at all or flash very fast and triggers warning circuits on newer cars) If there is one or more bulbs out, they must be replaced.
That being said, I doubt that alone is your problem. Here is a general automotive wiring primer aimed at the turn signal, hazard, stop, and running lights on most all motor vehicles.
Hazard flashers are required by D.O.T. safety standards on all motor vehicles that may ever be used anywhere near a public road. They are also required to be able to be used without the ignition key. This means the flasher circuit for hazards is fed thru a fuse that connects straight to the battery and is energized at all times.
Turn signal circuits often share the same flasher relay as the Hazards, even though the power for them is switched through the ignition key. Power for directional blinkers connects to a fuse, then the ignition switch, then to the battery.
So, if you have to turn on the turn signals (is the key on?) to get hazards to work, that means they are not getting power direct from the battery, but can get it when the turn signals are on because they both use the same relay. This is usually the case on all vehicles; If 4-way flashers and turn signal are both on at once, the 4-ways override the turn signal and force all signal bulbs to flash. The turn signal never forces one side of the hazards to stop blinking.
So, where does that leave us? You simply have a blown fuse, my friend. The hazard lamps fuse may also power the cigarette lighter, dome light, or other "always on" accessories. This varies with make & model, but the Hazard Lps fuse is usually well marked in the fusebox. If the fuse blows again shortly after being installed, do not put in a larger one! Try one more. If it also blows immediately, there is a problem with the wiring, or a bulb could be in wrong and shorting to the socket ground. Try removing all the flasher bulbs and trying the switch(it won't flash or "tick-tock") again. If the fuse does not blow, you have found the problem. Good hunting!

Apr 15, 2013 | 2000 Isuzu Trooper

1 Answer

Need to locate where turn signal flasher is in 1988 isuzu pick up


FLASHER

1988 Isuzu Truck Truck 2WD 2.3L 2BL 4cyl

The Flasher is located: Front seating area, driver side, under dash, near fuse panel, taped to dash wiring harness

If you still can't find it turn the signal on and listen for it.

Feb 12, 2013 | 1988 Isuzu Pickup 2WD

2 Answers

Where is the turn signal relay on an escort 1992


you have a fuse box under the dash and a fuse/relay box under the hood.
Althou many cars will place the flasher/blinker relay under the dash near the brake pedal, and still, some are behind the radio (farther back and close to the floor)
here is the relay you are looking for.
12_14_2012_3_59_39_am.jpg
You can turn on the hazard flashers and listen for the ticking sound the flasher makes. Follow the sound and look for a small round or square piece. (the flasher)
You should have one for blinkers and one for hazards.
This flasher is most often the problem.
Relay may be in the area if not under hood.

Dec 14, 2012 | 1992 Ford Escort 4 Door

1 Answer

1992 nissan maxima no indicators working


check the fuses first then if they are good then you could have a bad signal flasher that needs to be replaced.do the lights work front and back when trying the signals,if so then it could be the flasher.note that the hazard flasher looks the same as the signal flasher,also do the hazard lights work when operated if so this indicates the signal flasher as well,and eliminates the turn signal switch as the problem.

Sep 01, 2011 | 1992 Nissan Maxima

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Turn signals dont work at all


Try your hazard lights. If they work, then it's your turn signal flasher. With your hazards on, listen under the dash for the constant "clicking". Locate the flasher for your hazrads... the turn signal flasher should be near it. Once you find it, just pull it out and replace.

You can use your hazard flasher in place of your turn signal flasher, just swap the two. This will get you to the store to buy a replacement.

Jun 08, 2009 | 2005 Hyundai Accent

1 Answer

Turn signals dont work headlights dont dim heater fan doesnt work


Did all these problems happen all at one time?? If so you may have a bad body ground. Try running a electrical wire from the (-) negative side of the battery to the body and see if this works. Be sure this wire is to a place with no paint as low voltage electricity will not flow through paint.
A). If not try replacing the turn signal flasher for the turn signal problem. This is usually the culprit and it's easiest and cheapest to replace. The turn signal flasher will be found under the driver side dash next to the hazard flasher. Turn the hazard flasher one to locate it. If you want try swapping the turn signal flasher with the hazard flasher to see if this fixes it. They are the same style flasher.
If this doesn't work you may a faulty turn signal switch or some wiring issues.
B). It could as simple as the head lights bulbs need to be replaced, it's rare but I have seen when both bulbs blew at or near the same time. If your able check the voltage at the head sockets.
C). Could be a bad blower motor or switch. I'm not sure if these models have a resistor block or not. The resister block controls the electrical current going to blower motor which controls the speed of the blower fan.

Jan 19, 2009 | 1992 Dodge Caravan

2 Answers

Location of flasher for turn signal


  1. Access the COMBINATION Turn Signal and Hazard INDICATOR FLASHER on the Left-Hand (drivers) side of the instrument panel in the fuse junction panel.
  1. Remove turn signal flasher/hazard indicator flasher by pulling indicator flasher straight out.
  1. To install, align the terminals of the flasher and press into place.
How about a picture--

388df46.gif

Oct 03, 2008 | 1996 Ford Thunderbird LX

Not finding what you are looking for?
1995 Isuzu Pickup Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...