Question about 2000 Hyundai Elantra

2 Answers

Factory stereo removal

To whom it may concern

In order to remove and replace factory fitted stereo, is it necessary to remove the dash facia? If so, how do I go about it?

Please help

Posted by on

  • jaredhaygood Oct 19, 2008

    i have a 2000 hyundai elantra i removed the screws to remove the dash fascia but i cannot pull it out far enough to disconnect all the controls what should i do

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

I also had to remove the center panel,be careful with the heater controls,i didn't fully disconnect the hot/cold selector and fixing that was allot worse than putting in the cd player.

Posted on Oct 19, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

Yes, you have to remove the instrument panel center bezel to get to the mounting screws in the radio.

Posted on Oct 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the in-dash radio in my 2002 Fleetwood Bounder 36S gas RV?


Should be a normal install. Remove faceplate and skinny nuts on the volume and station preset knobs. Remove surrounding plastic,if necessary. There will be a rear support bracket at the back of the unit. Some wires back there.

Nov 11, 2014 | Cars & Trucks

Tip

How to install Radio in Honda Accord


Things You'll Need:

* Stereo
* Wiring harness
* Dash kit
* Phillips screwdriver
* Heat shrink
* Lighter
* Wire strippers
* Wire caps


In order to install A Radio first follow steps of Removing the Factory Radio


#1
Open the center console, and you'll see two phillips screws at the bottom. Unscrew both of them.

#2
Remove the drink tray, and unscrew three more phillips screws. The center console is now loose enough to move.

#3
Pull the center console back a few inches to expose two more screws under the plastic part of the gear shift. Remove these screws.

#4
Pull the ashtray out of the dash, and you'll see one more phillips screw. Remove this screw and pull off the plastic panel around the factory stereo.

#5
Locate the metal tray under the factory pocket (below the stereo), and pull it out of the dash. There will be two phillips screws holding it in place; remove those, and then pull the stereo out of the dash. You'll need to unplug the wiring harness that is plugged into the back of the radio.


Now Install The New Stereo

#1
Assemble the dash kit, as shown in the instructions. Put it into the dash where you just took the stereo out. There will be a rectangular opening, and a pocket underneath. The opening is where the radio will go.

#2
Secure the dash kit by screwing in the one screw in the ash tray, and the two in the opening of the panel.

#3
Insert the metal cage that came with the stereo into the opening above the pocket. Ensure that the fit is flush with the pocket. Using a screwdriver, bend the metal tabs upward, which holds the metal cage in place.

#4
Start wiring the stereo harness to the wiring harness. Match wires color by color until all of the wires are paired. For example, if you find a purple wire coming out of the aftermarket wiring harness, plug it into a purple wire from the factory harness. You aren't touching any of the wires in your dash on this step, you are simply wiring the new stereo to the wiring harness.

To connect these wires you'll want to place a piece of heat shrink over one of the wires, strip the ends, twist both ends together, and then pull the heat shrink over the exposed metal parts of the two wires. Heat the heat shrink with a lighter until it shrinks and forms a tight bond between the two wires. When done correctly, you won't be able to pull the wires apart.

#5
Plug the aftermarket harness into the factory plug, and insert the radio back into the dash. If you find wires that don't have a match, be sure to cap them so that the ends aren't exposed. Exposed wires are what cause shorts and electrical problems.

#6
Work in reverse order to put the dash back together. The radio won't be secure in the dash until the dash is put back together.

Hope this helps

Thanks

on Oct 07, 2010 | Honda Accord Cars & Trucks

1 Answer

2005 Ford Crown Vic, Cruise Control stopped working after I installed an aftermarket stereo. Alpine All-on-One


This sounds like as you have explained the removal of the factory fitted stereo is connected to the controls/ steering column by fitting the new stereo some electrical items remain unconnected. The volume control may be in circuit.
I have experienced this before on other models when fitting non factory extras.

Jan 12, 2013 | Cars & Trucks

1 Answer

Remove dash on 2002 chevy tracker and remove factory stereo and install new one


Glad I didn't read this page before I replaced my stereo.

Remove stereo fascia with three screws - 1 at the top, two on each side of ash tray. Remove 4 screws holding in stereo. Done - takes about 3 minutes.

Oct 29, 2011 | 2002 Chevrolet Tracker

1 Answer

How do you take of the dash paneling to install a new aftermarket cd player?


  • Disconnect the negative battery cable from the Jeep Cherokee battery with the 10 mm wrench.
  • 2 Remove the five screws on the top edge of the dash panel with a Phillips-head screwdriver.
  • 3 Pry the trim panels surrounding the climate control knobs away from the dashboard with the trim panel removal tool.
  • 4 Remove the trim panel that surrounds the headlamp switches (located to the left of the steering column) with a trim panel removal tool.
  • 5 Remove the two screws behind the trim panel that surrounds the headlamp controls with a Phillips-head screwdriver.
  • 6 Pull the dash panel that surrounds the stereo and covers the instrument panel of the Cherokee, away from the dashboard by hand.
  • 7 Remove the two screws from the stereo mounting bracket. One screw is on the bottom left corner, the other screw is on the top right corner. Each screw can be removed with the 10 mm socket and drive.
  • 8 Pull the factory stereo from the stereo mounting dock.
  • 9 Disconnect the stereo wiring from the back of the factory unit.
  • 10 Connect the Jeep Cherokee factory stereo wiring to a wiring harness adapter. Connect the wiring harness adapter leads to an aftermarket stereo. Slide the aftermarket stereo into the stereo mounting bracket and replaced two screws at the opposite corners with the 10 mm socket and drive.
  • 11 Replace dash panel that stretches across the top of the steering column.
  • 12 Replace the two screws at the top of the headlamp control switch. Replace the trim panel around the headlamp switch.
  • 13 Replace the trim panel that surrounds the climate control knobs.
  • 14 Replace the five screws on the top edge of the dashboard with a Phillips-head screwdriver.
  • 15 Replace the negative battery cable over the negative battery terminal and tighten the cable to the negative lead post with the 10 mm wrench



  • Dec 24, 2010 | 2006 Jeep Grand Cherokee

    1 Answer

    I have a 1993 Toyota Previa and need to change the stereo in it but the stereo is in the consule bit but cant remove it as it was factory fitted. How do I remove it pls Dont want to ruin the dash or its...


    Removal & Installation

    1. Disconnect the negative battery cable. Wait at least 90 seconds on models equipped with an airbag.
    2. Remove the assist grips on either door.
    3. Catrefully remove the garnishes on the door pillars.
    130a225.jpg Pry the panel on the side of the dash with a tapped ended screwdriver

    1. Pull the rear edge of the side defroster nozzle upward and remove it.
    2. Remove the steering wheel.
    3. Unscrew and separate the steering column covers.
    4. If necessary, remove the door scuff panels.
    5. Remove the two screws and extract the side panel.
    6. If necessary, remove the hood release lever. Unscrew the lever and pull if forward to remove.
    7. On the cluster finish lower panel remove the two small covers and remove the 5 screws retaining the panel.
    8. Five bolts retain the knee panel, loosen and remove them.
    9. Push up the release lock at the center on the lower side of the cluster finish center upper panel.
    bcca214.jpg
    Lift up the center upper panel to access the J/B and R/B No. 1

    Oct 31, 2009 | 1992 Toyota Previa

    1 Answer

    How can i replace the manufacture radio in my car and replace it with aftermarket car stereo


    You best bet, because of a warranty, is to have a professional shop install your stereo. But if you are like all of us guru's here, you like to get your hands dirty.

    First you need to remove the dash around your factory stereo. Be patient here and try not to break any of the dash. You may need to remove screws and pop loose plastic retainers located on the backside of the dash.

    Wire the after market stereo to the harness located below by maching the colors provided. Thank the stereo companies for making this simple. Use crimp connectors or solder your connections, which ever best suits you. Tape up any remaining wires with eectrical to minimize the chance of a short.

    Take the metal sleeve provided by the sereo you choose and install it into the install kit located below. Once you have removed the factory stereo, test fit the install kit and attach any tabs neccessary provided by the kit.

    Now take the aftermarket stereo and place into the sleeve you installe din the install kit until it clicks into its locks. Now, the harness you wired up earlier, plug it into the factory harness and then into you stereo. Hook up the antenna, you may need to purchase a antenna adapter. Now before you install the stereo, do a test run to make sure everything is working. Once you are content that it is all working, install the new stereo and then reverse the steps in removing the dash panel and stereo.
    Below are pictures of the needed hardware:
    b1a0aa3.jpg

    742ca2a.jpg

    Sep 14, 2009 | 2003 Pontiac Vibe

    1 Answer

    How to hook up a kdc-105 kenwood in a sunfire


    There are 3 things you need to purchase for this install. 1) The factory spec install kit. 2) The factory spec additional wiring harness. 3) Antenna adapter.

    Find the easied way to remove the plastic cowling around the radio and ac controls. Usually you can locate screws helping to retain the plastic dash parts. Be careful not to break the plastic dash by taking your time and looking over and over the part ofr connection hardware. Once you have located and removed all/if any screws, carefully pry out on the piece you are removing. There are often metal clips on the back of the piece that also help to retain the dash. Once that is removed, unbolt/unclip the factory stereo and slowly pull it out of the dash. Remove the factory harness from the backside of the factory stereo. DO NOT CUT THE HARNESS!! The wiring harness you have purchased is designed to plug and play into the factory harness. All you hae to do is color match the Kenwoods harness with the one you purchased. When wiring the two harnesses together use connectors **** a **** connectors, crimp connectors so forth and so on. If there is wiring you will not be using, take some electrical tape and tape the bare wire. We don't want a short. Once you are sure and have doubled checked that all the wiring is secure and matched, reverse the order of disassembly.

    The plastic install kit should replace the factory radio size difference. Just remember to take the metal sleeve tha came with the kenwood and install it into the plastic install kit via the instructions provided. Slide the Aftermarket stereo into the sleeve you just installed. Then you are ready to make all the needed connections. Before you reassemble everything make sure to do a test run with your stereo. If all is well reassemble and jam on.

    Sep 10, 2009 | 1999 Pontiac Sunfire

    1 Answer

    Facia panel removal to change radio


    YOUTUBE HAS GOOD VIDEO ON FORD CAR
    RADIO REMOVAL.

    Apr 13, 2009 | 2004 Ford Fusion

    1 Answer

    Remove factory radio


    Must have special U-shaped tool to release latch on both sides of radio. Tools are sold in sets as it requires one on both sides of radio. Insert tool about a half inch and the slightly push towards outside of stereo to remove. A little tricky for first timers

    Mar 29, 2009 | 1993 Mercury Grand Marquis

    Not finding what you are looking for?
    2000 Hyundai Elantra Logo

    1,155 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    64286 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21990 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...