Question about 1993 Mercedes-Benz 190

2 Answers

1993 190e 2.6 transmission problem

I have a 1993 190e 2.6 automatic... it goes in reverse but no forward gears. I replaced the modulator valve.. checked hoses. replaced trans fluid. still no forward. No metal shavings in pan very clean.. no warning just quit.Please help. thanks Sandy

Posted by on

  • 3 more comments 
  • dreski2dre73 Nov 05, 2008


    1. my 93 190e 2.3 will shift in drive and reverse and take of fine when accelerating but will not shift to 3rd gear


  • solartechmax Dec 16, 2008

    where is the gear switch on 88 190e. My trans does not shift into any high gear, car has 130k on it. Is there a relay or fuse for this? Please help!

  • Anonymous Mar 18, 2014

    1999 chevy astro goes into reverse, but no
    forward gears. Should I replace fluid, filter and selonoids? Thanks for any help you can provide.

  • Anonymous Mar 21, 2014

    Transmission slips into neutral and the car will struggle to move forward unless I feather the gas. What do you think the issue is?

  • Anonymous Mar 31, 2014

    won't go in forward gears only reverse

×

2 Answers

I have a 93 MB 2.6 190E . went to junkyard, got same tranny, spent 500 bucks to replace. Drives fine. No metal shavings on mine either but changed tranny, ok.

Posted on Oct 17, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Try to check a gear swich.if it is good then chech all wire, lead. if that not help, so it is time to change a gear box.

Posted on Oct 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 hyundai elantra goes in2 reverse but won't go backwards all other gears r perfect


Most automatic transmissions have a separate belt for reverse and all forward gears, The reverse belt is commonly lighter duty that the forward belt (some Chryslers were affected so much it was advised to not shift into reverse until the engine had warmed up and the automatic choke idled down) Thus your car would be in "reverse" but with no motion getting to the gears.

Jun 04, 2016 | 2001 Hyundai Elantra

2 Answers

2002 ford explorer will drive forward but wont move in reverse...what could be the cause?


bad transmission. if it shifts through gears going forward but will not do anything in reverse it is most likely a bad transmission. reverse is usually the first gear that goes out .

Dec 07, 2014 | 2002 Ford Explorer

1 Answer

What would stop a transmission from shifting ?


On a newer car this is a mode the transmission goes into when there is a bad problem with the transmission. It will usually go into 2nd gear where you can drive it safely to get it checked out but will not shift into any other forward gears.

Oct 09, 2014 | Cars & Trucks

1 Answer

Automatic transmission of toyota sera i couldn't move reverse it gets stuck rest is fine


It may be due to:
- Maladjustment of the gear lever cable or selector assembly.
- Valve body assembly.
- Planetary gear unit.
- Reverse clutch.

Nov 27, 2013 | 1992 Toyota Sera

1 Answer

Gearbox only goes forward in all gears on automatic gearbox


Sounds like transmission is failing and may need to be replaced or atleast have it looked at by mechanic,,,this would be my suggestion and good luck and if need help in future fill free to contact me...

Aug 16, 2012 | Cars & Trucks

1 Answer

Automatic Transmission goes into all forward


check fluid if it is a dark color and stinks transmissions probably needs rebuilt sounds like low reverse or direct clutch is bad trna will still go into loe by using forward clutch if low reverse is bad shoul be having problems with 3rd or direct in forward if forward clutch is bad

Nov 11, 2009 | 2000 Ford Ranger SuperCab

1 Answer

1992 Buick Lesabre, V6, Automatic with Air. When


Fit a manual gearbox ,could be cheaper in the long run

Oct 23, 2009 | 2002 Jeep Grand Cherokee

2 Answers

Hyundai excel 1996 automatic will engage reverse and park but no forward gears. Gearbox was overhauled 3 years ago, new seals etc. Oil level in the main transmission is ok and no apparent leaks. Problem...


It appears you have a Forward Clutch FAILURE. Replace the trans after you get it diagnosed and verified by a professional technician. By the way, do you have a Check Engine light? If so, what is the diagnostic code? The dealership can scan the system and find any codes which may have been stored in the TCM (Transmission Control Module). If there were any 'Incorrect Gear Ratio" codes, it's most probably the trans itself.

May 16, 2009 | 1994 Hyundai Excel

2 Answers

E4OD Trans stays in OD no matter where the shifter position is.


Transmission Description The E4OD transmission is a fully automatic, electronically controlled, four-speed unit with a torque converter clutch. The main operating components of the E4OD transmission include a torque converter clutch, six multiple-disc friction clutches, one band, one sprag one-way clutch and two roller one-way clutches that provide for the desired function of three planetary gear sets. Transmission gear selection in the (D) range and converter clutch operation is controlled by the powertrain control module (PCM) (12A650). Operating conditions are relayed to powertrain control module by various sensors throughout the vehicle. The powertrain control module compares these conditions with electronically stored parameters and logically determines how the transmission should operate. A torque converter (7902) couples the engine to the transmission gearset via the input shaft (7017) and the torque converter impeller hub. The impeller hub provides engine rpm to the positive displacement pump. The flow from the pump is proportional to engine rpm, and excess pump capacity is exhausted back to the pump inlet. The input shaft transfers power into the transmission gearset. The power input is controlled by the application of the torque converter clutch, which is scheduled through the powertrain control module. The application of the piston plate effectively replaces the hydraulic coupling between the converter cover and the turbine with a mechanical coupling between the converter cover and the turbine hub. This mechanical coupling helps improve fuel economy and wide-open throttle performance by eliminating converter slip. Transmission shift selection and torque converter clutch operation are controlled by the PCM. They are calibrated to provide the optimal transmission state. This state is commanded to the transmission solenoid body. In the (D) range, automatic operation of all four gears is possible. The transmission control switch, located on the vehicle's shift lever disables overdrive operation and enables automatic operation through the first three gears. Whenever the ignition switch is turned on, the vehicle will automatically provide overdrive operation regardless of the switch position the last time the vehicle was running. Manual gear selection is available in the 1 and 2 range. Second gear is commanded when the gearshift selector lever is in the 2 range and when downshifted into the 1 range at speeds above approximately 56 km/h (35 mph) (for diesel 48 km/h [30 mph]). First gear is commanded in the 1 range at start-ups and when downshifted into 1 range below approximately 56 km/h (35 mph) (for diesel 48 km/h [30 mph]). Any reference to intermediate brake drum or direct clutch cylinder are one and the same.
------------------------------------------------------------------------
253d68f.gif
I think this is your problem:

Programmable Speedometer/Odometer Module (PSOM): Description: The programmable speedometer/odometer module receives input from the rear brake anti-lock sensor, which is mounted on the rear axle differential housing. The PSOM processes this input signal information and relays it to the powertrain control module and the speed control module. This signal tells the powertrain control module the vehicle speed in miles per hour (mph). Used as an input in determining shift scheduling and electronic pressure control. Symptoms: Harsh engagements, firm shift feel, abnormal shift schedule, unexpected downshifts may occur at closed throttle, abnormal torque converter clutch operation or engages only at wide-open throttle (WOT). May flash transmission control indicator lamp. Diagnostic Trouble Codes: 452, P0500, P1500, P1501, P0503

Mar 21, 2009 | 1993 Ford F150 SuperCab

1 Answer

Transmission problem 1993 190e 2.6 mercedes


Hi!
Base on the information gaven it seems that your forward clutch pack is worn,thats the reason you have seen that metal shaving in the transmission pan.So get your transmission repair.

Aug 26, 2008 | 1993 Mercedes-Benz 190

Not finding what you are looking for?
1993 Mercedes-Benz 190 Logo

1,072 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...