Question about 1989 Dodge Ramcharger

2 Answers

Water pump assembly and power steerin pump brackets

Havin a problem gettin brackets back togther after replacin water pump need visual aid to see how brackets go back together its also older than 83

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I need a diagram to re-install the water pump and brackets for my 1989 dodge ram charger 360 engine.

Posted on Jan 21, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 74 Answers

Need to know year? engine size?what accesories equipped? a/c power steer smog pump etc.

Posted on Aug 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering pump bracket assembly


Go back to the STORE, they ship Cores every 2-3 Days.... They have the box marked and they can get it back for you...

Apr 09, 2013 | 1993 Nissan Altima

1 Answer

92 4runner runs hot after a new waterpump


air pocket in block find heater hose take off either end pour antifreeze in radiator until runs out of hose or block with motor not running then put hose back on

Dec 22, 2012 | 1992 Toyota 4Runner

1 Answer

Change water pump


Instructions
    • Raise the hood of the KIA and locate the battery. Disconnect the positive and negative cables.
    • 2Drain all of the coolant from the radiator and engine assembly. If you do not do this it will result in a large mess when you disconnect the hoses and the pump.
    • 3
    • Use a screwdriver to remove the mounting screws from the lower splash shield. Remove the shield from the vehicle. Disconnect both the air duct and fan by removing the screws which hold them in place.
    • 4Use a socket wrench to remove the tension bolt which is fixed to the alternator. This is the bolt that attaches the alternator to its bracket. Once the bracket is disconnect you will be able to slide the belt off the alternator. Remove the mounting bolt on the bottom of the alternator. Lift the alternator clear of the assembly. If you are struggling to move it on your own, have help on hand to aid in the lifting process.
    • 5Remove the coolant reservoir and radiator hoses from the engine assembly. On most Sportage models the coolant reservoir will have no mounting bolts and can be removed manually. You should be able to simply remove the hoses from the vehicle by pulling them with your hand.
    • 6Use a wrench to remove the tensioner bolts which fix the water pump in place. Lift the damaged pump out of the KIA.
    • 7Insert the new pump in the same place from which you removed the old one. Remove the old gasket and replace it with a new one at the contact point of the water pump. Fix the new part in place with the mounting bolts to a torque of 19 lbs. Place the reservoir coolant and radiator hoses back into the engine assembly by pressing them in to their connectors.
    • 8Attach the alternator to its bracket by fixing the mounting bolts in to the bottom. Attach the belt to the alternator and fix it in place with the tension bolt. Place the splash shield back on the vehicle and insert the coolant back in to the radiator. Reattach the battery terminals and turn on the engine to check that the water pump is now working correctly. Keep an eye out for leaks.

Aug 30, 2012 | 1997 Kia Sportage

2 Answers

2003 Mitsubishi Galant Idler Belt Tensioner Replacement


I also need help knowing how to replace the belt tensioner pulley. It looks like you can't get out the bolt because the pulley is real close to the frame, unless the bolt has nuts on both ends, but it doesn't look like it.

Dec 03, 2011 | 2003 Mitsubishi Galant

1 Answer

Havin problems wiv my vw golf startin in mornin keeps turnin over but wont start but does wen i put jump leads on but battery seems to have powwer plus wen i put full steerin lock wen car stood still it...


Hi

the battery is weak although it may have power to turn the engine over it is not enough to make it start, it will need changing. the other fault is common with loosing revs while turning full lock. this is often a loose power steering belt or power steering rack or pump starting to fail. to be honest though they seem to last forever like this and there are a number of wheel related faults such as bottom suspension arms, ball joints and bushes that can also make the car do this as the steering is extended beyond where it's maximum capacity is.

Hope this helps
Regards
Dan

Jan 04, 2011 | 2000 Volkswagen Golf

1 Answer

Step by step to replace water pump on a 1995 chevrolet camro.


Water Pump - REMOVAL & INSTALLATION
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
3.4L ENGINE
(see Figures 1 and 2)
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Remove the air intake duct.
  4. Remove the top coil of the ignition coil pack.
  5. Loosen the tensioner pulley bolt/screw.
  6. Disconnect the heater hose from the water pump.
  7. Loosen the water pump pulley bolts/screws.
  8. Unfasten the power steering bracket bolts/screws.
  9. Remove the serpentine drive belt.
  10. Remove the water pump pulley.
  11. Remove the power steering pump bracket and swing the bracket and pump aside. Do NOT disconnect the power steering lines from the pump.
  12. Unfasten the water pump and engine front cover bolts/screws, then remove the water pump assembly from the vehicle.
  13. Remove and discard the gasket and thoroughly clean the gasket mating surfaces.
9940b19.jpg

Fig. 1: Exploded view of the water pump mounting - 3.4L engine

To install:

  1. Position a new water pump gasket, then install the pump. Secure using all of the water pump retaining bolts/screws, except the bottom three, and tighten to 33 ft. lbs. (45 Nm).
  2. Install the engine front cover bolts/screws and tighten to 16 ft. lbs. (21 Nm) for 1993-94 vehicles, or to 97 inch lbs. (11 Nm) for 1995 vehicles.
371be42.jpg

Fig. 2: Water pump retaining bolt tightening sequence
  1. Install the three bottom water pump retaining screws and tighten to 89 inch lbs. (10 Nm).
  2. Place the power steering pump into position and install the pump bracket.
  3. Install the water pump pulley.
  4. Install the serpentine drive belt.
  5. Install the power steering pump bracket retaining bolts and tighten to 30 ft. lbs. (40 Nm).
  6. Connect the heater hose to the water pump.
  7. Install the top coil to the ignition coil pack.
  8. Attach the electrical connector to the alternator.
  9. Install the air inlet duct and air cleaner assembly.
  10. Connect the negative battery cable.
  11. Fill the cooling system. Start the engine and check for leaks.


3.8L Engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Remove the serpentine belt.
  4. Disconnect the radiator inlet hose from the water pump.
  5. Unfasten the water pump pulley bolts/screws and remove the pulley.
  6. Remove the water pump pulley retaining bolts, then remove the pump from the vehicle.
  7. Remove and discard the gasket and thoroughly clean the gasket mating surfaces

To install:
  1. Position a new water pump gasket, then install the pump. Secure using the water pump retaining bolts/screws and tighten to 11 ft. lbs. (15 Nm), plus an additional 80 degree rotation.
  2. Install the water pump pulley and retaining bolts. Tighten to 115 inch lbs. (13 Nm).
  3. Install the serpentine drive belt.
  4. Connect the radiator inlet hose to the water pump.
  5. Connect the negative battery cable.
  6. Fill the cooling system. Start the engine and check for leaks.

5.7L ENGINE
  1. Unplug the electrical connector from the cooling fan.
  2. For 1993-95 vehicles, remove the right side cooling fan.
  3. For 1996-98 vehicles, remove both cooling fan assemblies.
  4. Place a suitable drain pan under the vehicle, then remove the block coolant drain plug and the knock sensor. Drain the radiator.
  5. Install the drain plug and knock sensor.
  6. Remove the air intake duct and air cleaner.
  7. Disconnect the upper and lower radiator hoses from the water pump.
  8. Remove the heater hoses from the water pump and throttle body.
  9. Unplug the electrical connector from the coolant sensor.
  1. Unfasten the retainers and reposition the ignition coil and bracket.
  2. If equipped, remove the air pump and bracket.
  3. Unfasten the water pump attaching bolts, then remove the water pump and discard the gasket. Remove the shaft coupling and water pump driveshaft seals, if necessary.
  1. Thoroughly clean the gasket mating surfaces
To install:
  1. If removed, install the shaft coupling and water pump driveshaft using J 39089 or equivalent water pump driveshaft O-ring installer.
  2. Install the water pump with a new gasket. Tighten the bolts to 30-32 ft. lbs. (41-43 Nm).
  3. If equipped, install the air pump and bracket.
  4. Reposition and secure the ignition coil and bracket.
  5. Attach the coolant sensor connector.
  6. Connect the heater hoses to the water pump and throttle body.
  7. Connect the upper and lower radiator hoses to the water pump.
  8. Install the air cleaner and air inlet duct.
  9. Install the electric cooling fan(s), then attach the electrical connector.
  10. Refill the cooling system.
  11. Connect the negative battery cable, then start the engine and check for leaks.


Hope helps (remember rated this).

Jul 01, 2010 | 1995 Chevrolet Camaro

1 Answer

Steerin wheel is hard of my ford tempo car . i


Hi:
If you have power steering, first check to see if you have fluid in the power steering reservoir. If you don't have power steering, you most likely have binding in the rack and pinion unit, and that has to be replaced as an assembly, and is a bit pricey, so check your fluid first.

If the fluid is full the power steering pump could be bad, but usually they growl, and are noticeable.

Oct 26, 2009 | 1991 Ford Tempo 4 Door

2 Answers

Water pump replacment precedure on 2001 jag stype 3.0


Hello
To replace water pump : Raise the car
1- Drain cooling system. 2- Remove drive belt tensioner clip (if there is one) 3- Remove accessory drivebelt * Rotate the belt tensioner counter clock wise , 3/8 inch square drive bar should do it
* Remove accessory drive belt
4- Lower the car 5- Remove the upper shield. 6- Remove the throttle body. 7- Detch the coolant hose from housing assembly. 8- Remove the upper radiator mounting bracket 9- Detach the hose assembly from the water pump and lower hose. 10- Remove the hose assembly * Detach the hose clips
11- Remove intake manifold support bracket * Detach wiring harness
* Remove intake manifold support bracket
12- Detach coolant hose from water pump 13- Remove coolant hose from the water pump to lower housing. 14- Remove water pump
Installation :
in reverse order and make sure to use new gaskets and seals

Jul 07, 2009 | 2001 Jaguar S-Type

2 Answers

Water pump removal (cant get power steering pump out)


To access and remove the waterpump, the powersteer bracket has to be removed completely. To do this, the rear camshaft drive pulley must be removed (need a tool to hold pulley, bolt tight) and then the thin sheetmetal shield behind the pulley. This allows access to the lower powersteer bracket bolts.
Removal of the engine mount is also required to perform timing belt replacement. It also helps to increase your access room too.
I would recommend you replace the waterpump why you are there as they have a tendancy to fail at around 140000 km's.

May 23, 2009 | 1994 Mitsubishi Diamante

1 Answer

1995: 8Cyl 5.7L GAS, FI, VIN "K" Sierra SLE


  1. Remove coolant
  2. loosen off alternator belt tension
  3. loosen off power steering pump tension if applicable
  4. Same with AC if needed
  5. remove fan hub bolts
  6. remove belts shared by water pump pulley
  7. remove hoses from water pump
  8. remove heater core hose from water pump
  9. remove alternator support bracket bolt thru water pump housing
  10. remove power steering bracket support bolt if applicable
  11. remove AC bracket support bolts if applicable.
  12. Now remove water pump housing to block bolts(remember sequence)
  13. using a pry bar or large screw driver, gently pry the water pump until it releases from the block
  14. clean all old gasket material from connecting surfaces
  15. Place new gasket in place with a little bit of spray tack
  16. then re-install water pump and install bolts as they came out(some are longer than others)
  17. Re-assemble all parts in reverse order of removal
  18. fill system with new coolant
  19. start vehicle and test for leaks before driving anywhere(make sure you have a drop pan under the vehicle
  20. Let the vehicle come up to operating temperature,,do final check for leaks with Radiator cap on
  21. If you have access to a cooling system pressure pump and tester, it would be easier to use this tool to test system.
  22. Road test vehicle, add fluid if necessary, enjoy driving.!!

Jan 11, 2009 | 1997 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...