Question about Chevrolet S 10

2 Answers

I have a 1989 s-10.The parking brake light blinks six times,pauses then flashes again.I was wondering what trouble code that would be???Thanks.

Posted by on

  • Anonymous Feb 01, 2009

    Parking Braking Light Stays on 1989 Chey truck 1/2 ton

  • ttilley1 Feb 11, 2009

    i have an 89 checvy silverado 1500 that flashes 8 short 1 long. any idea on the code?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

RWAL Fault codes
Codes for Dodge RWAL, Ford RABS and GM RWAL applications are similar but have a few differences:

  1. Should not occur (replace the controller if it does)
  2. Open isolation valve circuit or defective ABS module
  3. Open dump valve circuit or defective ABS module
  4. Grounded or closed RABS or RWAL valve switch
  5. Excessive actuations of dump valve during ABS braking
  6. Erratic speed sensor signal
  7. Shorted isolation valve or defective ABS module
  8. Shorter dump valve or defective ABS module
  9. High resistance or open speed sensor circuit (resistance should be 1000 to 2500 ohms)
  10. Low speed sensor resistance (Dodge & Ford only)
  11. Open speed sensor circuit (GM only)
  12. Stop lamp switch circuit (Dodge & Ford)
  13. ABS module speed processor (Dodge & Ford only)
  14. ABS module program (Dodge & Ford only)
  15. ABS module RAM memory failure (Dodge & Ford)
To manually clear a stored fault code on GM and some Dodge trucks with RWAL, remove the ABS fuse or disconnect the battery for 5 seconds. Ford RABS codes will automatically clear when the ignition is turned to the off position.

Posted on Aug 26, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 74 Answers

Code six plus how many flashes after pause is code respond with code i will look it up for you

Posted on Aug 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Check engine light flashes car won't start


you can get the trouble codes out by turning key on off on off on then watch the check engine light it will flash a number of times n pause this will give you codes to take to the auto parts store n tell them they will know most of them the service writer at the dealer can find the rest (example) blink blink blink pause blink blink =32 there could be several so do it a couple times to make sure you get them right and get them all

Mar 15, 2012 | 1992 Plymouth Acclaim

Tip

OBD1 Trouble codes, without a scan tool.


Here is a tip for retrieving Diagnostic Trouble Codes (DTCs) from any OBD1 GM vehicle. <br /><br />First thing is your going to need to get a paper clip, and bend it into a U shape. <br /><br />Now stick the ends of the paper clip into the 2 top right hand side holes in the connector. Note: Do this with the key in the run position, but with the engine off.<br /><br />You should now see your check engine light flash once, pause, then 2 times. This indicates that your ECM is working properly.<br /><br />Now it will blink indicating your code. For example an EGR failure code is DTC 32. You will see your light blink 3 times, pause, then blink 2 times, giving you code 32.<br /><br />A list of codes can be found here: http://www.gmtuners.com/OBD1_DTC.htm.<br /><br />Hopefully this helps some of you all out there. Thanks for looking.

on Jan 04, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

Toyaota Camry 1994 engine won't start, Engine light on


I would check for fuel,(pressure and injector pulse), spark, and compression, before checking any codes. Lack of any of these basics can result in codes, and then you waste alot of time chasing a symptom, instead of the actual problem.If more people followed basic diagnostics, which always come back to these three basics, rather than chasing codes first,they would find no starts much more quickly.

Nov 14, 2011 | 1994 Toyota Camry

1 Answer

I have a 1994 plymouth voyage se and it will not strat. It tell me to check gauge light comes on. what should i do or what does that mean?


Turn key to on ( not start) then off, then on, then off, then on and leave on, and have a pen and paper ready to record flashes of "check engine light". It will flash then pause between second number of 2 digit code. Then a short pause and flash again, pause, then flash. For example: if it flashes 2 times, then pause, then flashes 2 more times, that would be code 22. If it flashes 3 times, pause, then flashes 5 more times, that would be code 35. As I said, there will be a short pause between 2 digits, as well as after number. Write them down as they come up and get back to us with those codes for advice. When you get code 55 ( 5 flashes, pause 5 more ) that means end of message. Those codes should point everyone in right direction of trouble spot.

Jul 31, 2011 | 1991 Plymouth Grand Voyager

1 Answer

My 94 jeep loaps and then backfires out the tail pipe can you solve


Power train control module controls the drivetrain. If you can get a code from the computer it would go a long way diagnosing wether its an engine malfunction or computer issue. To get the codes bring a pen & piece of paper out to the car, turn the key to the run position (not start but when all the dash lights come on) then off then run then off then run (three times in the on position, after you have turned the ke on then off 3 times on then leave the key in the on position and watch the check engine light. It will flash a code to you for example check engine light turns on then off 1 time with a long pause then the light flashes three times then another pause this would be the #13 code , most start with this code to tell you that it is checking codes. Just count the # of flashes (from the check engine light) & that is the first # of the code it will pause then flash again & that is the second # of the code. Flash 5 times pause then 5 more flashes is the # 55, & that is the last code you get to indicate all codes have been displayed, so key on then off then on then off then on & watch the check engine light count the flashes write down that # when it pauses then count the next number of flashes until the pause & that is your trouble cod they are 2 # codes & usually 13 is the first code flashed & the # 55 is the code that lets you know it is done, all the 2 digit codes in between are trouble codes & can be found in a chiltons or haynes service manual or search the web for chrysler trouble or computer codes.

Sep 23, 2010 | Jeep Cherokee Cars & Trucks

2 Answers

I have a 2004 chevy aveo ls the abs light is on and sometimes it acts like it dont have brake any answers out there thanks


you need to have the abs computer scanned for trouble codes . i think that auto zone or advanced auto will scan it for free

Jul 11, 2010 | 2004 Chevrolet Aveo

1 Answer

My 93 geo is having trouble idling at drive but as soon as you put it back in park or neutral power is back on again. If stopped at a stop light I have to put it in Neutral to keep running or it gets...


check the TP Sensor. might need adjusted or replaced. Also could be the Catalytic converter. theres actually 2 on the exhaust and me living in Ohio we dont have emissions so im gonna hack both of um off and just run a str8 pipe from the header back. theres an extra fuse spot i believe its on the left side of the fuse panel. its raised up a lil higher then all the other fuses in it. throw a fuse in it and turn the key on the check engine light will blink a code or multiple codes. i.e. 2 flashes small pause 2 flashes is code 22 wich is the TPS. 2 flashes small pause 1 flash can also be the TPS 1 is low voltage the other is high voltage. but u can pull the whole list of codes from google type in 93 Geo Metro Trouble Codes Hope this helps

Oct 18, 2009 | 1993 Geo Metro

1 Answer

Check engine light on


Cycle your key, on (not start) off, on, off, on. Leave it on 3rd time, and count check engine flashes. It will be a 2 digit number each time. For example: flash,flash, pause, flash, flash. Is code 22.
Flash,flash,flash,pause,flash,flash,flash, is code 33. There will be a little longer pause after each set of 2 digits. When you get flash,5 times, then flash 5 times again, that's code 55 which means end of trouble code message. have a piece of paper ready, write them down, and get back to us with results.

Feb 20, 2009 | 1989 Plymouth Reliant

1 Answer

Air Bag Indicator Light blinks on 1995 Lincoln Town Car


The blinking light is giving you a code and according to what you have listed that would be a code 25. However there is no code 25 for this system are you sure that it is not a 52 instead? If so then this code is for a loss of power to the module. Did you have battery go dead recently? If this is the case then you can clear it yourself. You will have to locate a gray 2 wire connector behind the glove box first. Here are the instructions to clear the code 52.
  1. Cycle the ignition switch to OFF and then to RUN.
  1. Observe air bag indicator prove-out (six ± two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
  1. Locate the Diagnostic "Trouble Code Clear" Connector located underneath the glove compartment (06010) containing Circuits 631 (T/R) and 57 (BK).
  1. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.
  1. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
  1. Release short on Circuit 631 (T/R) to Circuit 57 (BK). This short must be released within 25 seconds after the diagnostic monitor tone sounds.

Jan 25, 2009 | 1995 Lincoln Town Car

1 Answer

98 Dodge Stratus won't start


Best place to start is with "check engine light". Put vehicle in park, foot on brake, and cycle key on, off, on, off, on, then wait with pen & paper ready to read flashes of check engine lamp. Will be a 2 digit code each time. For example, flash, short pause & flash, will be 11, or flash, flash, short pause, flash, flash would be 22. In between trouble codes you'll get a little longer pause, then it will start to flash again if more than one code, which is quite possible. Also note that I say key to on, not start, just on.(normal run position) Then get back to us and we'll be able to better help you.

Nov 28, 2008 | 1998 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,054 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...