Question about 1995 Ford Bronco

1 Answer

So we are pretty sure its the distributer then......good im glad i have something to pin it on

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

Thats great get-r-done

Posted on Aug 26, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My blazer wont start

Check the main relay in your power distribution box.

Mar 04, 2015 | 2001 Chevrolet Blazer

1 Answer

Why won't my car start after replacing distributer?

have you checked tthe timing and also make sure the shear pin on distributer gear is not broke

Dec 01, 2014 | 2004 Nissan XTerra

2 Answers

The power outlet in the front drivr side by the cup holder doesnt work.

The power outlets get their power from the power outlet relay. The power outlet relay gets its power from fuse #21 in the Power Distribution Center (PDC) in the engine compartment. It is a 20 Amp fuse. If the other power outlet works, it is not caused by the relay or the fuse. You most likely would have a broken wire or defective power outlet in this case.

Jun 13, 2011 | 1997 Plymouth Voyager

1 Answer

Im pretty sure my power window motor just went out and i still have to drive it. How can i get it up without the motor? ive lifted on it and it wont budge. its a 1997

Try tapping the window motor with a hammer or something as you are pushing the button and sometimes this will loosen the motor up enough to turn it on to go up. It's worked for me in the past but not every time. I hope this helps you and good luck.

Mar 22, 2011 | Mercury Cougar Cars & Trucks

1 Answer

I have a 1986 chevy 1 ton truck it will turn over but it is not firing to start. it want to crank but something is stopping it

i would replace the ignition control module, i pretty sure if you take the distributor cap off the module is mounted to the bottom of the distributor housing, not as hard toreplace as it sounds, when you go buy the new one ask the auto parts attendant about its location, but im pretty sure im right

Jan 22, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

Im trying to disconnect the slave cylinder from the line

I'm pretty sure it's just held in by a roll pin and has to be pushed out. Check for a little dimple on either side. Get a small punch in there, and once started, work it out with a pair of pliers, vice grips, of wire cutters.

Feb 28, 2010 | 1996 Mazda Pickup

1 Answer

1987 nissan 300zx intermitent no spark no start

I have a 90z an there was a statement about the Ignitor Coupling.. Crank Angle Sensor is the problem sounds like.When it is heating up/Electric current doesn't flow as good. Change plug wires also because when they get heated it allows the fire to jump outa the wires. My Z before it thru a rod an blew a big hole in the oil pan would never start when it was cold. Never did really figure that one

Jul 07, 2009 | 1988 Nissan 300ZX

1 Answer


hi there, you need to make sure all wires to spark plugs are tight and very snug, you will also need to check the distributer cap to make sure no burns are on it, and make sure the plugs are in proper firing positions, the spark rotation might be out of sequence.....also make sure spark plugs are clean of all oil, and dirt, firing pin in distributer cap might be bad.....hope this

May 21, 2009 | 2006 Hyundai Sonata

1 Answer

How to Change out the Raditor

I'm pretty sure that if you read some of the instructions in manuals that somewhere around item 1-3 to remove when beginning the job!
Sure glad you did not remove any A/C lines!!!!

Apr 17, 2009 | 1999 Jeep Grand Cherokee

1 Answer

2001 Saab 95 se driver/passenger windows.

A car I owned the left rear window did that. I could pull it up by taking a hold of it while another person held the switch. They told me the problem was the track was made out of plastic and it had broken. They had to replace the track. Yes it was expensive to repair but is ok now.

Mar 10, 2017 | 2000 Saab 9-3 Viggen

Not finding what you are looking for?
1995 Ford Bronco Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5622 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides