Question about Jeep Liberty

1 Answer

Check engine code transmission control circuit

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 60,769 Answers

You check for codes through the under dash diagnostic (drivers side lower dash) connector, Kragen asuto parts will do this for free.

Posted on Aug 25, 2008

3 Suggested Answers

  • 8 Answers

SOURCE: 2002 Dodge Durango 4.7L V8 Check Engine Codes

1st try and search for a vaccum leak, due to the fact that these vehicles have had some bad problems with the length of wires and hoses, if there is a vaccum leak in the vehicle somewhere that will trigger other malfunctions in your vehicle. Using a can of starting fluid or Brake cleaner spray lightly spray around our engine til you hear the motor rev-up and the spot you have sprayed will determine where your vaccum leak will be. And then check under your distributor cap for any moisture be sure to take a rag and wipe and residue off. Also check the firing order on your distributor.

Posted on Oct 28, 2009

  • 1986 Answers

SOURCE: check engine code "P0446 Evap Control System Vent Control Circ"

Unfortunately, this code has nothing to do with the gas cap....
A code P0446 could mean one or more of the following has happened:

  • Faulty vent valve
  • Open, short or excessive resistance on Vent valve control circuit
  • Blockage of vent valve
  • Bad PCM
Here are some things you could try to fix it:
  • Replace Vent valve
  • Repair open, short, or resistance problem in control circuit
  • Repair open, or short, or resistance problem in power circuit
  • Replace PCM


Posted on Nov 17, 2009

  • 1170 Answers

SOURCE: check engine light on

The problem may be with the boost control valve below the battery. Water getting into the electrical connector is a common problem because the valve is mounted low down.

Posted on Jun 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What are possible causes of P1768 code on a 2001 Chrysler PT Cruiser?


hello, this code is for the transmission control relay and below is a list of possible causes
CHECKING SYMPTOMS AND POSSIBLE CAUSES
LOW BATTERY VOLTAGE CAUSING SYMPTOM
FUSED B(+) CIRCUIT TO TRANS CTRL RELAY OPEN
TCR GROUND CIRCUIT OPEN
TRANSMISSION CONTROL RELAY CIRCUIT OPEN
TCM PIN 16 TO TCR OPEN OR BAD CONNECTION
TCM PIN 17 TO TCR OPEN OR BAD CONNECTION
TRANSMISSION CONTROL RELAY DEFECTIVE
NO OUTPUT FROM TRANSMISSION CONTROL RELAY
TCM TRANS RELAY CONTROL CIRCUIT SHORT TO VOLTAGE
INTERMITTENT CODE P1768


Read more: http://www.justanswer.com/chrysler/2n3oc-does-code-p1768-mean.html#ixzz417aVuKgP

Feb 24, 2016 | 2001 Chrysler PT Cruiser

1 Answer

I'm looking for a code identifier


Definition of check engine code P1792:
Acura
TRANS EEPROM Checksum Error
Chrysler/Dodge/Jeep
Battery power was disconnected since last power down
Citroen/Peugeot
Barometer Pressure Circuit Malfunction
Ford
Barometer Pressure Circuit Malfunction
GM
Transmission Control Module Reprogrammable Memory
Honda
Problem in Engine Coolant Temperature (ECT) Sensor Circuit
Isuzu
Trans EEPROM Checksum Error
Jaguar
Ignition Supply Malfunction
Kia
Ignition Supply Malfunction
Mercedes
Barometer Pressure Circuit
Opel
CAN data bus,ECMITCM communication - malfunction detected
Volkswagen/Audi
Transmission Range Display Circ. Short to B +
Volvo
Transmission Range Display Circ. Short to B +

Dec 13, 2015 | Cars & Trucks

1 Answer

What that erorr p0744 in maxiam 2011 .. that they need replacing ??


P0744 Torque Converter Clutch Circuit Intermittent OBD-II Trouble Code Technical Description Article by Dan Weller ASE Certified Master Technician Torque Converter Clutch Circuit Intermittent This diagnostic trouble code (DTC) is a generic OBD-II powertrain code. It is considered generic because it applies to all makes and models of vehicles (1996-newer), although specific repair steps may vary depending on the model. What does that mean? Modern vehicles equipped with automatic transmissions / transaxles use a torque converter between the engine and transmission to increase the engine torque output and drive the rear wheels. The engine and transmission are actually connected by a fluid coupling mechanism inside of the torque converter which is what multiplies the torque until the speeds equalize and create a "stall" speed where the difference in actual engine RPM and transmission input RPM is around 90% efficient. Torque converter clutch (TCC) solenoids commanded by the Powertrain control module/Engine control module (PCM/ECM) or the Transmission control module (TCM) to direct hydraulic fluid and engage the torque converter clutch to create a solid coupling and increase efficiency. The transmission control module has detected a fault with the circuit that operates the torque converter clutch solenoid. Note: This code is similar to codes P0740, P0741, P0742 and P0743. There may be other diagnostic trouble codes associated with the transmission control module that can only be accessed by using an advanced scan tool. If any additional transmission related DTC's appear in addition to the P0744, an electrical failure is likely. Symptoms Symptoms of a P0744 trouble code may include: Intermittent Indicator Lamp (MIL) illuminated (a.k.a. Check Engine Light) Minimal decrease in fuel economy, this will not affect engine performance Potential Causes Causes of this DTC may include: Wiring harness to transmission damaged, loose connection, or intermittent open/short circuit Torque converter clutch (TCC) solenoid Transmission control module (TCM) Diagnostic Steps for P0744 DTC Wiring harness - Check transmission wiring harness for damage or loose connections. Use a factory wiring diagram to locate the appropriate power source and all connection points between circuits. The transmission may be powered by a fuse or relay, and triggered by the TCM. Disconnect the transmission harness at the transmission connector, power source and TCM. Check for a short to ground inside the transmission internal wiring harness by locating the appropriate + and - pins for the torque converter clutch solenoid. Using a digital volt ohm meter (DVOM) set to ohms scale, check for a short to ground in the circuit with the positive lead on either pin and the negative lead to a known good ground. If resistance is low, suspect a short to ground the internal harness or the TCC solenoid - removing the transmission oil pan may be necessary to further diagnose the TCC solenoid. Test the wiring between the TCM and the wiring harness connector at the transmission case using the DVOM set to ohms. Check for a possible short to ground by moving the negative lead on the DVOM to a known good ground, resistance should be very high or over limit (OL). Test the wiring for the control circuit between the TCM and the wiring harness connector at the transmission case using the DVOM set to volts scale - it may be necessary to remove the pin from each side of the harness connector to isolate it from the harness while it is still plugged into the TCM and transmission case. With the positive lead on either end of the wiring and the negative lead to a known good ground, check for the presence of battery voltage with the key on/engine off. If voltage is present, suspect a short to power and determine the source of the short circuit in the wire harness assembly. Hint: Wiggling the wire harness and connectors while testing may help locate an intermittent short to power or ground. Torque converter clutch (TCC) solenoid - Check the resistance in the TCC solenoid and internal transmission wiring at the transmission case after removing the transmission harness plug (if applicable, some makes/models use a TCM bolted directly to the transmission case). Some makes/models use a transmission wire harness with the TCC solenoid and internal harness as a single unit. The DVOM should be set to ohms scale with the positive lead and negative lead on the pins for the TCC power and control circuit. Resistance should be within manufacturers specifications, if it is very high or over limit (OL), remove the transmission oil pan to inspect the solenoid inside the transmission if possible. Check for voltage on the power side circuit of the TCC solenoid with the key on/engine off and harnesses plugged or at the wire harness connector at the TCM with the DVOM set to volts scale, positive lead on the control side of the solenoid and the negative to a known good ground with the vehicles key on/engine off, battery voltage should be present. Tap the solenoid and wiggle the wiring to determine if a short to power or ground exists. Transmission control module (TCM) - Since the torque converter clutch is only activated during certain driving conditions, it will be necessary to monitor the TCM with an advanced scan tool to determine if the TCM is commanding the TCC solenoid and what the actual feedback reading is at the TCM. The TCC solenoid is normally controlled by a duty cycle to engage a more comfortable torque converter cluch engagement To test if the TCM is actually sending the signal, a graphing multimeter set to duty cycle or a digital storage oscilloscope will be required as well. The positive lead is probed into the wiring harness plugged into the TCM and the negative lead to a known good ground. The duty cycle shold be the same as being commanded by the TCM in the advanced scan tool reading. If the cycle is intermittent on rough road conditions, it may be a wiring fault. Re-check connections and if all wiring / solenoid is OK or if road conditions do not coincide with the intermittent readings, the TCM may be at fault.

Read more at: http://www.obd-codes.com/p0744
Copyright © OBD-Codes.com

Apr 24, 2015 | 2011 Nissan Maxima

1 Answer

P0701 tranny code


Possible causes
- Open or short transmission control system circuit
- Poor transmission control system electrical connection
- Check powers and grounds to Transmission Control Module (TCM)
What does this mean? What does this mean?
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
Read more:
P0701 Transmission Control System Range Performance

Jan 13, 2015 | Cars & Trucks

1 Answer

Codes 32 75 12 22 on a check engine light


first code it's P0320 Possible causes
- Faulty Ignition/Distributor engine speed sensor
- Faulty Crankshaft Position sensor
- Ignition/Distributor engine speed sensor harness is open or shorted
- Ignition/Distributor engine speed sensor circuit poor electrical connection
- Low battery charge
- Faulty Engine Control Module (ECM)


Read more: http://engine-codes.com/p0320_ford.html#ixzz3DcwddSlp
2- P0750 Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid 1 valve
- Shift solenoid 1 valve harness or connectors
- Shift solenoid 1 valve circuit is open or shorted


Read more: http://engine-codes.com/p0750_ford.html#ixzz3DcwoXS73
3- P0120 Possible causes
- Faulty Throttle Position Sensor
- Throttle Position Sensor circuit is open or shorted
- Throttle Position Sensor poor electrical connection


Read more: http://engine-codes.com/p0120.html#ixzz3Dcx3VCPs
4- P0220 Possible causes
- Throttle Position Sensor (TPS) harness is open or shorted
- Throttle Position Sensor (TPS) circuit poor electrical connection
- Faulty Throttle Position Sensor (TPS)
- Fault Electric Throttle Control Actuator (or Throttle Body Motor)
- Accelerator Pedal Position Sensor (APP)


Read more: http://engine-codes.com/p0220.html#ixzz3DcxGUMl4

Sep 11, 2014 | 1991 Ford F150

1 Answer

Diagnostic code p0701


P0453 means EVAP emission pressure sensor high input. Possible causes:
- Faulty Evaporative Emission System (EVAP) Pressure sensor
- Evaporative Emission System (EVAP) Pressure sensor harness is open or shorted
- Evaporative Emission System (EVAP) Pressure sensor circuit poor electrical connection.
Code p0701 means Transmission control system range/performance. Possible causes:
- Open or short transmission control system circuit
- Poor transmission control system electrical connection
- Check powers and grounds to Transmission Control Module (TCM)

Aug 27, 2013 | Cars & Trucks

2 Answers

Codes P1782, P0755, and P0700


P1782 DODGE - 2/4-OD Pressure Switch Circuitxicon.jpghttp://engine-codes.com/p1782_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4-OD Pressure Switch
- 2/4-OD Pressure switch poor electrical connection
- 2/4-OD Pressure switch circuit is open or shorted
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Transmission shift shockP1782 DODGE Description The pressure 2/4-OD Pressure Switch is part of the pressure switch of the transmission. The pressure switch are located in the solenoid assembly. The switch provide input information to the Transmission Control Module (TCM). The switch will inform to the TCM is pressure exist in a specified hydraulic circuit. the TCM uses this information to verified that the solenoids are working or not.
P0755 DODGE - 2/4 Solenoid Circuitxicon.jpghttp://engine-codes.com/p0755_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty 2/4 solenoid valve
- 2/4 solenoid valve harness is open or shorted
- 2/4 solenoid valve circuit poor electrical connection
P0700 DODGE - Transaxle Control System Malfunctionxicon.jpghttp://engine-codes.com/p0700_dodge.htmlForum CodePossible causes- Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Jul 26, 2012 | Plymouth Breeze Cars & Trucks

1 Answer

1998 Chrysler Sebring convertible Not shifting into drive check engine light came on, error code PO715


DTC P0715 CHRYSLER - Input Speed Sensor 1 Circuit
P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible shifting problems

Possible causes
- Transmission speed sensor circuit is open or shorted.
- Poor transmission speed sensor circuit connection
- Faulty transmission speed sensor

Hope this clues helps to solve it.

Jun 02, 2011 | 2003 Chrysler Sebring

3 Answers

Check engine light comes on after approx. one minute. My code reader gives me a 214 in continuous memory ( cylinder ID circuit failure). I clear the code and it comes back. What is giving me this code?...


look 214 is not a valid code for a 1995 escort, this is an OBD1 system. here is a list of trouble codes for this year of ford no matter the model.

You should find the diagnostic connector under your hood normally by the fender on the battery side. By just using your test light and a jumper wire, it will tell you what kind of problem you got.

KEY ON ENGINE OFF (KOEO) TEST
Model years 1984-1995 all models of Ford
1. Make sure engine is fully warmed. If in doubt, run engine at 2000 rpm for 2 minutes.
2. Turn ignition off and wait 10 seconds for system to shut off. Make sure A/C is off and transmission is in Park (automatic) or Neutral (manual).
3. Hook up light and jumper (or a tester if you have one). Turn key to ON (do not start engine). Read the codes.

How to do it?

Example code 23: your test light should flash 2 long consecutive flashes followed by 3 short pulses.

Ford's common codes for OBD1 (vehicles made before 1995)

11 system pass
12 idle control fault
13 dc motor did not move
14 engine rpm signal fault or PIP circuit failure
15 eec processor or power to KAM interrupted
16 rpm to low to check oxygen sensor test or fuel control error
17 cfi fuel control system fault or rich/lean condition indicated
18 ignition diagnostic monitor (IDM) circuit failure
19 cylinder identification (CID) sensor input failure
21 engine coolant temperature (ECT) out of self-test range
22 manifold absolute pressure (MAP) sensor circuit out of range
23 throttle positioner sensor out of self-test range
24 air charge temperature (ACT) sensor out of self-test range
25 knock not sensed during dynamic response test
26 transmission fluid temperature out of self-test range
28 loss of primary tach, right side
29 insufficient input from vehicle speed sensor
31 egr positioner sensor below minimum voltage
32 egr positioner sensor below closed limit
33 throttle positioner sensor noisy/harsh on line
34 egr valve circuit out of self-test range
35 egr valve circuit above maximum voltage
38 idle track switch circuit open
39 axod torque converter or bypass clutch not applying properly
41 oxygen sensor circuit indicates system always lean
42 oxygen sensor circuit indicates system always rich
43 oxygen sensor out of self-test range
44 air injection control system failure
45 coil 1 primary circuit failure
46 coil primary circuit failure
47 4X4 switch is closed or oxygen sensor failure
48 coil primary circuit failure
49 electronic transmission shift error
51 engine coolant temperature sensor circuit open
52 power steering pressure switch circuit open
53 throttle position circuit above maximum voltage
54 air charge temperature circuit open
55 key power input to processor open circuit
56 mass air flow circuit above maximum voltage
57 axod circuit failure
58 idle tracking switch circuit fault
59 automatic transmission shift error
61 engine coolant temperature circuit grounded
62 converter clutch error
63 throttle positioner circuit below minimum voltage
64 air charge temperature circuit grounded
65 charging system over voltage
66 mass air flow sensor circuit below minimum voltage
67 neutral/drive switch circuit open
68 transmission fluid temperature over temperature range
69 transmission shift error
70 data circuit communication link circuit failure
71 message center circuit circuit failure
72 insufficient manifold absolute pressure (MAP) change during dynamic response test
73 insufficient throttle positioner (TPS) change during dynamic response test
74 brake on/off (BOO) circuit open
75 brake on/off (BOO) circuit closed
76 insufficient air flow output change during test
77 brief wide open throttle not sensed during test
78 power interrupt detected
79 a/c on/defrost on during self test
81 map has not changed normally
82 super charger bypass circuit failure
83 OIC-low speed fuel pump relay circuit failure
84 egr vacuum regulator (EVR) circuit failure
85 canister purge circuit failure
86 shift solenoid circuit failure
87 fuel pump circuit failure
88 electro drive fan circuit failure
89 transmission solenoid circuit failure
91 no oxygen sensor switching detected
92 shift solenoid circuit failure
93 throttle positioner sensor input low
94 torque converter clutch solenoid circuit failure
95 fuel pump secondary circuit failure
96 fuel pump secondary circuit failure
97 transmission indicator circuit failure
98 electronic pressure control circuit failure
99 eec has not learned to control idle

Jan 14, 2010 | 1995 Ford Escort

2 Answers

P0700, P0750 and P0755 codes I was driving at 65 mph and the 2003 Dodge Caravan down shifter to low gear and the check engine light came on. It will not ship to high gear.


P0700 (M)
Check Transmission DTC's
This code indicates that the EATX (Transmission controller) has an active fault and has illuminated the MIL via a BUS message. The specific fault must be acquired from the EATX via a DRBIII tool. (Input or Output Speed Sensor failures often cause this code and are a common failure part on WJ Grand Cherokees

P0750
Shift Solenoid circuit.
Note: If code P1767 (Transmission Relay Always On) is also present: Replace transmission solenoid assembly. See note provided. When transmission is in limp mode the relay that provides power to the solenoid group is switched off. This is normal and is designed to provide operation in one gear only. Engineering department suggests to replace transmission solenoid assembly anytime these two trouble codes occur together. See applicable service manual section (21) for solenoid assembly replacement directions. IMPORTANT: When performing this repair always check torque on all valvebody accumulator cover plate screws. Proper torque specification is 70 inch pounds. If any accumulator cover plate screws are damaged or missing replace the valvebody assembly. NOTE: If any other trouble codes are present do not replace solenoid assembly. See test in the applicable Transmission Diagnostic Procedures Manual

P0755
Shift Solenoid B

Oct 14, 2009 | 2003 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...