Question about 1995 Oldsmobile Silhouette

1 Answer

Tail light change

How do you get to the light balb?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Open the rear window next to the taillight. Use a phillips head screwdriver to remove the screws and then flip open the clips. Remove the housing and replace the bad bulb. Do everything in reverse and you are done.

Posted on Sep 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2009 taillight won't come on but my brake lights is working ok


hi.check balb can be blown it can have a double contact balb in that has two lights in it one can be blown

Jan 17, 2016 | Cars & Trucks

1 Answer

2003. when I turn turn signal on when lights are off it works fine and when I turn head lights on I get both tail lights flash a little bit and fast as if a balb was out help


If I understand what you are trying to say. I believe you have one of three issues. Issue one is that your flasher unit is bad allowing the power to travel backward. Issue two you may have a bad headlight or turn signal switch. Try lifting on the lever just a little to see if the problem stops. Also if the headlight switch is bad it may become hot to the touch. Last is you have a wire short or you are missing a ground. Check the wiring harness under the bed near the back of the vehicle and see if you have lost the frame ground.

Jan 04, 2016 | Chevrolet S 10 Cars & Trucks

2 Answers

Right rear blinker not working, no windows, and key wont go to off position


On the windows you just may have a blown fuse to then. And as far as the key not going to the off position you may have to shake the wheel side to side to get the key to move to the off position. Now on the blinler and tail light. Take the scoket out and remove the balb. There is probley going to be some corrotion in it. Use some Coke a Cola and with the light off pour some in it and then dry it out. You will see 4 contacts in there make sure they are shiny and then look at the balb to see if you may have a blown bulb. Replace and reinstall.

Dec 02, 2012 | 2009 Chevrolet Traverse

1 Answer

Both front blinkers do not blink.theres power to the blinkers.all light work parking,driving. tail light binkers work,but blink fast. i looked at all balbs, all good


could be a faulty earth on teh front lights ,use a meter to locate the feed wire ,then earth the other side of holder and see what happens also check for continuety across the bulb

Jan 08, 2011 | Ford Ranger Cars & Trucks

1 Answer

Looking for a tail light wiring diagram for 2004 Dodge Ram 1500. Needing to find which wire is used for reverse light


low beam kigth out on driver side replaced balb an still dont work this is om my 2004 dodge ram 1500

Dec 08, 2010 | 2004 Dodge Ram

1 Answer

Headlights not working.checked circuit and have power to fuses and plug,replaced headlight and still nothing.what should i check next?


if you have power at the head light plug or pig tail then you have a bad ground turn the head lights on and probe the ground wire with the balb still in if the lights come on the run new ground wire or find the broken wire and repair it

Jan 11, 2010 | 1987 Honda Accord

1 Answer

No break lights work... water in back trunk


if ther was alot of water in it i would get a new tail light. check the fuse to see if it popped and change the balb. if the light has a small crack it can easly be sealed with silicone.

Dec 23, 2009 | 2007 Chrysler Sebring Sedan

1 Answer

How do I change out the backup lights on my 2003 chevy impala, without having to take it to the dealer?


in the trunck behind the tail light pull the carpett down you shuld find either finger screws or little bolts that hold the light in take the bolts out and remove the tail light. to replace the balbs all you have to do is twist the pig tail socket and it will come out of the tail light.

Dec 23, 2009 | 2003 Chevrolet Impala

2 Answers

Dashboard lights wont come on


you could have fried a wire take a es ligh and pull the dash apart and test were the balbs go in oher wise check check the balbs they could have went out

Apr 17, 2009 | 2000 Hyundai Accent

Not finding what you are looking for?
1995 Oldsmobile Silhouette Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...