Question about 1993 Chrysler New Yorker

1 Answer

1194 New Yorker

How do I loosen the tensioner pulley for the serpentine belt on my 1994 Chrystler New Yorker

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,498 Answers

Hi Sulli,

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Posted on Dec 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a serpentine belt on my 1990 new yorker


Write a diagram of the pulleys and belt direction release the tensioner or alternator adjusting bolt remove old belt and fit new one, check idler pulley bearings for noise and wear.

Nov 15, 2014 | 1990 Chrysler New Yorker

1 Answer

How do you change the serpentine belts on a 2.5l chrystler sebring?


The idler pulley has a locking bolt and an adjuster bolt. The lock bolt is the center bolt on the pulley-loosen it first. The adjuster bolt is to the side, behind the pulley. Turn it to release tension on the belt. Rout the new belt on and tighten the adjusting bolt, first, then the locking bolt at the center of the pulley.
Bit of a strange set-up. I never thought the center bolt would need loosening first, but that's how it's done.

Apr 28, 2013 | 2006 Ford Taurus

1 Answer

How do I replace the serpentine belt on a 1994 concorde?


Remove the alternator/power steering pump and water pump drive belt to gain access to the air conditioning drive belt.
To remove and install the air conditioning compressor drive belt, first loosen the tensioner pulley lock nut, then turn the adjusting screw to raise or lower the tensioner pulley assembly Accessory Drive - 3.3L Engine or Accessory Drive - 3.5L Engine To adjust the air conditioning drive belt, loosen the tensioner pulley nut and adjust belt tension by tightening adjusting screw. Torque pulley nut to 54 N•m (40 ft. lbs.) after adjustment.
The Poly-V generator/power steering belt has an adjustable tensioner pulley located on the timing belt cover Accessory Drive - 3.5L Engine to maintain proper belt tension. To remove or install this belt, Release tension by loosening the tensioner pulley nut and adjustment bolt Accessory Drive - 3.5L Engine Reverse procedure to install and tighten belt to specified tension.

Jul 10, 2012 | 1994 Chrysler Concorde

2 Answers

I am trying to hange the serpentine belt on my 09 lancer rallyart and it keeps slipping off


Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2 Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
  • 3 Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
  • 4 Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
  • 5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
  • 6 Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
  • 7 Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
  • Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    Where is the serpentine belt tensioner & how do I loosen it?


    The belt tensioner will be a single pulley with a spring loaded arm on it. It will have either a 1/2 inch or 3/8 inch square hole in it. Use the appropriate ratchet or breaker bay and turn it in the direction that loosens the belt. After routing the new belt save the tensioner pulley for last and do the same thing to install the new belt. It's always best after replacing the belt to check each pulley to be sure the belt is running firmly down and even on the pulley. It's easy to have the belt one groove off which will quickly tear the new belt to pieces. Please rate this answer, thanks.

    Feb 04, 2011 | 1994 Plymouth Voyager

    1 Answer

    Replace alternator belt


  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • Oct 08, 2010 | 2002 Mitsubishi Lancer

    2 Answers

    Change serpentine belt on 06 sienna


    1. 1 Check to ensure the Sienna's engine is cold, then make sure the Sienna is in park, the ignition is in the off position and the key is removed from the ignition to prevent any possibility of the engine engaging during the serpentine belt replacement.
    2. 2 Open the hood and locate the serpentine belt routing diagram sticker on the side of the engine casing. Study it for a moment before removing the existing belt. It is essential the new belt be installed exactly as the diagram indicates.
    3. 3 Find the tensioner pulley, the main pulley that controls the serpentine belt, and fit a 1/2-inch socket wrench over the self-tensioner on the outside of the pulley.
    4. 4 Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
    5. 5 Compare the old serpentine belt with the new, replacement belt for length, width and number of grooves on the belt's underside. Be certain the replacement belt is the right part.
    6. 6 Fit the new belt on to each pulley according to the serpentine belt routing diagram on the manufacturer's sticker, or according to the drawing made prior to removing the old belt. Fit the new belt on to the tensioner pulley last, again applying pressure on the pulley's self-tensioner with the half-inch socket wrench to loosen the pulley.
    7. 7 Release the pressure on the self tensioner and allow the tensioner pulley to ease back into place, thereby tightening the new serpentine belt with the appropriate tension.
    8. 8 Remove the wrench and close the hood.
    Thank you and good luck,
    Lee

    Aug 26, 2010 | 2006 Toyota Sienna

    1 Answer

    How do I replace a Serpentine Belt on a 1994 E420?


    The tensioner will keep the belt tight without having to adjust. It's on a spring loaded type arm. The tensioner is on a arm, if you look at the center of the roller you will see either a 1/2" hole or it could be a allen type wrench hole. You will need to fit a ratchet into the hole or an allen wrench with a pull handle for better leverage. Once you have this inserted into the hole, you will either push or pull slightly to compress the spring which will give you room to fit the belt over the last pulley. Once this is done the tensioner will automatically tighten the belt once you release the pull handle. You are set and ready to go

    Jul 16, 2010 | 1994 Mercedes-Benz E-Class

    1 Answer

    How to install a serpentine belt on a 1994 mercury grand marquis it seems that i can get a 3/8 or 1/2in ratchet to move tensioner


    It is sometimes pretty tough getting it to move.
    Make sure you are Rotating it the correct way.
    Do you have a Breaker Bar or a Serpentine Belt Tensioner Tool. Stores like Harbor Freight and even some Auto Parts Stores have these. Some of the auto parts stores have these for rent (for free with a refundable deposit).
    I like and use weekly the Serpentine Tool from Harbor Freight (Item #66344-0VGA- $20). It is narrow enough to fit in most tight spots. The main bar has a 3/8-in fitting, and the extension bar can connect to this with a 1/2-in fitting.
    The idea is to have more leverage. The Ratchet and/or Wrench sometimes does not provide that leverage needed.

    When installing follow the below guidelines. DO NOT try to put the Belt on the Tensioner last.

    "HOW TO":
    Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
    1. Find the Tensioner(s).
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
    Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

    Apr 07, 2010 | 1994 Mercury Grand Marquis

    1 Answer

    HOW TIO INSTALL THE BELT ON CHRYSLER NEW YORKER 1990 3.3


    There should be a single serpentine belt setup in that car. You need to
    find the springloaded belt tensioner pulley, put the right sized socket
    on it, with a long breakerbar or ratchet, and releive the tension from the belt to remove and replace it. There should be a sticker on the fanshroud area, which has the belt routing diagram on it. Good luck.

    Mar 31, 2010 | 1990 Chrysler New Yorker

    Not finding what you are looking for?
    1993 Chrysler New Yorker Logo

    190 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    chargerhp
    chargerhp

    Level 3 Expert

    813 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...