Question about 1996 BMW 318

1 Answer

Removing car door

I can't find a way to remove the driver's side door

Posted by on

  • Anonymous Nov 27, 2008

    door dented badly, needs to be replaced





    what pins need to be removed in order to do this successfully

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 52 Answers

Hii how are you

its soooo hard theres 2 screws under the handle unscrew them
unclip the clip on the window winder and unscrew that screw, pull hard its really fiddly have fun.

sorry good luck sur

Posted on Aug 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Remove driver side door panel 2003 ford expedition


First disconnect negative battery terminal.Underneath of armrest there is two screws, remove them, using small screw driver pry out armrest switch control plate and remove screw behind it, pry of the side mirror cover using wide putty knife. carefully start prying from the bottom of the door around going toward the top then lift the door panel over door lock knob. Carefully look under and disconnect all electrical connectors and remove the panel. Installation is in reverse order of removal!

May 05, 2014 | 2003 Ford Expedition

1 Answer

Remove door panel


Trim and molding remove tool and a phillips screw driver
Drivers Side

Remove
Door trim panel and water shield (top where window is)
Plastic panel around door handle. snaps out
1 screw upper front extension assembly (plastic triangle)
2 screws located lower bottom left (drivers side) and door trim panel
Use remove tool to push out retaining 'C' clip behind door handle
Grasp panel where opening are and pull up and out gently
Now disconnect wire harness

May 07, 2013 | 1991 Ford Thunderbird

1 Answer

The lock has fallen inside the driver's side door


Here is a common way to remove your door pannel:

1st, find the screw that is attaching the inside door handle (looks like an armrest) to the door panel. remove this screw. there is also a screw located at the door lever (the device you use to open the door from the inside). remove this screw. after this, slide your door panel up to remove it.

Aug 10, 2011 | 2007 Chevrolet Aveo Sedan

1 Answer

How to remove front dopr panel on 1995 Lincoln Town Car


Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

May 31, 2010 | Lincoln Town Car Cars & Trucks

1 Answer

How do I remove driver side door window


You need to remove inner door panel by unscrewing the screws on inner door handle and take a flat screw driver wedge it between the panel and door use flash light to see the clips along the sides and lower part of door and pry them free. then look through the inner door cut outs to find window track. Once you see it use ratchet or screw driver and loosen the window free form track. Then carefully remove window.

Apr 01, 2010 | 2003 Mazda MPV

2 Answers

How to remove/replace driver's side mirror on 96 blazer


remove door panel.. there should be access hole to get to the bolts.

Jul 31, 2009 | 1996 Chevrolet Blazer

1 Answer

Remove drivers side window motor


remove the door trim from the inside of the door, now remove the door plastic weather protector which should expose the window glass and also the electric motor and winder mechanism.
There will be a plastic wire connector inside the door which will have to be disconnected to remove the electric motor etc.
Hope this helps

May 19, 2009 | 1994 Pontiac Grand Am

1 Answer

HOW DO I REPLACE THE DRIVER SIDE POWER MIRROR ON AN 98 F-150?


Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.

Jan 31, 2009 | 1997 Ford Expedition

Not finding what you are looking for?
1996 BMW 318 Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...