Question about 1998 Dodge Ram 2500 2WD

1 Answer

Fuel guage i changed the fuel pump in my truck and now the gas hand wont work and the gas light stays on. does this need to be reset or is there something else we can do to fix this problem?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Did you change the the pump seal or seals as there may no pressure buld up in the tank to help the gauge work.

Posted on Aug 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 F350 4x4 regular cab V10 gas guage quit working I had the sending unit and fuel pump changed the fuel guage went to 1/4 and sat there. Any tips? Fuel guage wont work.


I'm assuming this has dual tanks, do you know if it is not working on both tanks ?
Most people would check the circuit for the gauge at the tank. The sending unit grounds the gauge on the dash.

Aug 31, 2012 | 2007 Ford F-350 Super Duty XLT

1 Answer

My gas guage is stuck on 3/4 tank being full what do i need to do to fix it


If the problem happened right after you replaced the pump, I would say the sending unit in the tank is not connected to the harness.
You could check the circuit to the gauge at the connector for the tank.

Aug 25, 2012 | Cars & Trucks

1 Answer

Gas gauge probloms on my 2001 impala it moves up and down only when full stays up but when i have it on half tank goes up and down when the gauge goes all the way to E the sencer turns on low fuel so i put...


There is no reset for that and to replace the fuel guage you have to change the fuel pump, now there is another way where you can clean the guage reader (patanchio) meter with a pensil eraser and it will work.

Oct 03, 2011 | 2000 Chevrolet Blazer

1 Answer

Fuel guage stuck on "E"


more then likely sending unit whent bad part of fuel pump assembly in tank

Jun 26, 2011 | Ford Focus Cars & Trucks

2 Answers

Where can I find a fuse for the gas gage on a 2004 Chrysler T&C


The gas guage does not have its own fuse but instead gets its power from the "integrated power module" that handles power delivery to the entire instrament cluster and beyond. If the guage is in-op,[doesnt work] then you will need to have a few "hands-on tests run to verify if the sending unit in the tank[fuel pump module] is functional or if this problem lyes else-where, wiring problem, bad ground,ect,ect.. One hint would be if the low fuel level l;ight still functions without the fuel guage working,then your problem is NOT in the tank and very likely is in your dash-electrical or faulty guage.
8w-40-2 106001316
8w-40-2

Jan 10, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

2000 Jeep Grand cherokee Laredo wont start. Engine turn over . No noise from fuel pump with ignition on. Replaced fuel pump and filter.Turn ignition on- pump did not run.Jumped the fuel pump at the pump...


sounds alot the the pcm it controls the fuel pump and ign system but the anti theft would keep it from starting because the key has a transponder in it programmed for that vehicle and that would kill all ign if triggered

Sep 22, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Wont start with key on guages do not work


check your fuses and relays, if it still wont start the PCM may have been damaged,have the truck check with a obd sacner.

Sep 08, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Was running-stalled-turns over but will not fire.gas guage wont move and gas light stays on


check and make sure you have plenty of fuel in the tank. gas light should not be on as long you have plenty of fuel in the tank unless you have faulty fuel level sensor. check if you getting sparks and fuel, pull wire and one plug out, ground it to the vech have a friend turn over the engine and see if you getting strong sparks. no sparks check coil having 12V, good coil, cam sensor faulty. check if you getting fuel, pulling hose from the fuel filter line, point it down ward wrapping the end with clothes covering the hose and turn the engine over, see if you getting proper fuel and good pressure coming out of the line using your thumb slightly cover the fuel line. no pressure or fuel, check the fuel pump, good pump, faulty crank sensor. both crank and cam sensor work the same way, one telling computer to send sparks to the plugs and other turn on the fuel pump.

Aug 30, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...