Question about Daewoo Lanos

1 Answer

What is the part called that fits the front radiator hose to the engine called?

Posted by on

  • mshep64925 Aug 25, 2008

    Thank you! Its the thermostat housing that broke off...will JB weld fix it? If not what size are the bolts do you know? I might get one at a salvage yard b/c I don't have time to wait on ordering it.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 120 Answers

Good day;
I have not worked on any Daewoo's but it should be the same concept. It could be one of two thing. 1. the hose could be just going into the thermostatic housing. 2. it could be going inti the water pump with the thermostatic include. Hope this helps. Could you discrib the part, this could help fining out which one it is.

Cheers.

Posted on Aug 25, 2008

  • Rob Cobb
    Rob Cobb Aug 25, 2008

    Hi did the housing break right into two, or is there just a crack? if it is just crack then you could get away with the JB weld, but make sure it's nice and clean. but the proper way is to replace the housing. For the bolts I believe that it's metric should be maybe a 12 mm or 13 mm. hope this helps Please keep me info.



    Cheers

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove radiator on 2000 Lincoln Continental


RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove the radiator.

Oct 21, 2016 | Lincoln Cars & Trucks

2 Answers

Where is Thermostat located?


Usually in the lower radiator hose.

Aug 19, 2015 | Cars & Trucks

1 Answer

How do I change the radiator on a 96 lincoln contiental 32v intech V8 ?


RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove Radiator

Apr 19, 2015 | 1996 Lincoln Continental

1 Answer

Leaking bottom radiator hose


Yes, you can do it! First, just check if the clamp on the end of the hose where it connects to radiator is just loose and needs tightening. That may be all it needs to stop the leak. When your new radiator was installed, sometimes the clamp may not have been tightened enough. If the clamp is just like a wire clamp and can't be tightened, buy a good screw clamp and fit it on. If that is not the case, you may need to pull off the lower radiator hose to investigate. Of course, to remove hose, you need to drain the radiator first. The other end of the hose goes to an inlet fitting to the water pump on the front of the engine. It will also have a clamp that you loosen or remove to pull hose off that fitting.
How it works is hot coolant in the engine is pushed by the water pump into the upper radiator hose and goes down through the radiator for cooling it and then back into the engine through the bottom radiator hose. The water pump constantly circulates the coolant through the engine to the radiator and back into the engine through the lower radiator hose.
I would bet you just have a loose fitting hose. See if you can tighten it first.

Dec 13, 2012 | Cars & Trucks

1 Answer

Steps on removing and replacing radiator on my 1999 jeep cherokee sport 6 cyl. stright


Things You'll Need
  • Waste oil collection pan
  • Needle nose pliers
  • Phillips head screwdriver
  • Wrench set
  • Socket set
  • Antifreeze
  • Water
armor-all-tyn2.png
  1. Draining the Cooling System
    • 1 Locate the petcock valve on the lower right corner of the radiator and place a waste oil collection pan underneath it.
    • 2 Open the petcock valve by turning it counterclockwise, using needle nose pliers.
    • 3 Wait until all the coolant has drained out then close the petcock valve by turning it clockwise.
    Removing the Radiator
    • 1 Loosen the hose clamp that connects the upper radiator hose to the radiator using a Phillips head screwdriver. Then pull the upper radiator hose off the radiator.
    • 2 Loosen the hose clamp that connects the lower radiator hose to the radiator using a Phillips head screwdriver. Then pull the hose off the radiator.
    • 3 Unscrew the transmission cooler lines from the radiator (automatic transmission only) using a wrench.
    • 4 Unscrew the bolts that secure the radiator to the core support, using a socket.
    • 5 Lift the radiator straight up to remove it from the vehicle.
    Installing the Radiator
    • 1 Lower the radiator into position behind the core support. Be careful: the cooling fins are thin and can be easily damaged.
    • 2 Screw the bolts that secure the radiator into the core support. Tighten with a socket.
    • 3 Thread the transmission cooler line fittings into the radiator. Tighten with a wrench.
    • 4 Slide the lower radiator hose onto the fitting on the bottom of the radiator. Slide the hose clamp over the fitting and tighten with a Phillips head screwdriver.
    • 5 Slide the upper radiator hose onto the fitting on the top of the radiator. Slide the hose clamp over the fitting and tighten with a Phillips head screwdriver.
    • 6 Fill the engine with a 50/50 mix of antifreeze and water.
    • 7 Run the engine and visually inspect for leaks.

Aug 30, 2011 | 1999 Jeep Cherokee 4WD

1 Answer

Car heating up need to know where the thermestad is located


Find the top radiator hose and trace it to where it goes on the front of the engine. When you take the radiator hose off that hose fitting you will see that the fitting has two bolts that hold it onto the intake manifold. The thermostat is between the manifold and the hose fitting. Take the two bolts off, take the fitting off and you will see it.

Good luck.

Aug 23, 2011 | 1998 Honda Accord

1 Answer

How do I remove the radiator from a 1986 buick century 2.5 engine?


This is a mechanical job and can be worked out according to the tools available at your end with the ground experience. The radiator is normally bolted in the front chassis which fits the front grill and merges with the front side panels. You need to remove the grill if access if to be efffective . so start from the front grill fitting and you will get access to the side fittings of the radiator which can be removed. The connecting hoses on the top and bottom must be carefully removed and hoses removed finally to lift up the radiator.

Aug 08, 2011 | Buick Century Cars & Trucks

1 Answer

How do I replace the radiator hoses


I hope this is a routine maintenance replacement...Ask to see the radiator hoses at your local parts store...the exact replacement is best used for a perfect fit...in rare cases the replacement has to be slightly modified...(usually length) be sure the fit clears all fans...etc...there are 2 hoses involved, called the upper, and lower radiator hoses...the upper attaches to the water inlet on the motor...and the upper radiator connection...the lower connects to the water pump, and the radiator...when removing expect a major water spill...try to catch with a trash can lid under the front of your Acura...use new hose clamps in re-assembly. Hope this helps.

Feb 21, 2011 | 2000 Acura TL

1 Answer

What is the procedure for removal of the radiator from the Mercury Mystique(1998 model)?


Ford Contour/Mystique/Cougar 1995-1999 Repair Guide

Radiator -REMOVAL & INSTALLATION
(see Figures 1 through 7)

7249321.jpg
Fig. 1: Remove the upper radiator hose from the radiator


d2d2436.jpg
Fig. 2: Use a back-up wrench to remove the transaxle cooler line connections-automatic transaxle only


3213ac8.jpg
Fig. 3: the lower transaxle cooler line connection


ec9272d.jpg
Fig. 4: Remove the passenger side radiator mount and ...


956cd3d.jpg
Fig. 5: ... and the driver's side radiator mount


f06fec0.jpg
Fig. 6: The condenser can be support using mechanic's wire as shown here, or another suitable device


242d821.jpg
Fig. 7: Carefully lower the radiator out the bottom of the vehicle
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Remove the upper radiator hose from the radiator.
  4. On 2.5L equipped vehicles, remove the radiator overflow hose from the radiator.
  5. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler inlet fitting and plug the line and the fitting.
  6. Remove the engine fan.
  7. Raise and support the vehicle.
  8. Remove the lower radiator hose from the radiator.
  9. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler outlet fitting and plug the line and the fitting.
Remove the cooler lines while holding the radiator connector with a back-up wrench.
  1. Support the radiator, and A/C condenser with a jackstand or other suitable device.
  2. Remove the lower radiator supports from the front of the subframe.
  3. Remove the two retaining bolts for the A/C condenser from the brackets at the bottom of the radiator.
  4. Position the jackstand aside and remove the radiator out the bottom of the vehicle.
To install:
  1. Carefully raise the radiator into place and support the radiator with a jackstand or other suitable device. Install the two retaining bolts for the A/C condenser into the brackets at the bottom of the radiator.
  2. Install the lower radiator supports and tighten the bolts to 71-97 inch lbs. (8-11 Nm).
  3. Remove the jackstand and install the transmission cooler outlet line (if equipped) and the lower radiator hose to the radiator.
  4. Lower the vehicle.
  5. Install and tighten the fan shroud nuts.
  6. Install the transmission cooler inlet line (if equipped) and the upper radiator hose to the radiator.
  7. On 2.5L equipped vehicles, install the radiator overflow hose from the radiator.
  8. Connect the negative battery cable.
  9. Fill the cooling system with the proper 50 / 50 mixture and start the vehicle.
  10. Bleed the cooling system and check for leaks.

Hope helps with this (remember rated this help) Good luck.

Jan 20, 2010 | 1996 Mercury Mystique

1 Answer

I need 2 know how to remove the radiator


THIS IS a 1995 LINCOLN CONTINENTAL W/4.6L ENGINE
iIBELIEVE TOWN CAR IS DIFFERENT LET ME KNOW IF SO AND PLEASE DONT FORGET TO RATE ME


REMOVAL
  1. Disconnect battery ground cable (14301).
  2. Drain engine coolant.
  3. Remove engine air cleaner (ACL) (9600).
  4. Remove upper radiator hose (8260) from water bypass tube.
  5. Remove radiator overflow hose (8075) from radiator (8005) and fan shroud (8146). NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  6. Remove transmission oil cooler line from oil cooler inlet fitting.
  7. Remove nuts retaining A/C condenser core to the radiator.
  8. Disconnect engine control sensor wiring (12A581) from the auxiliary electric cooling fan motors and the CCRM.
  9. Raise vehicle on hoist.
  10. Remove splash shield from lower radiator support (16138) and front sub-frame (5C 145).
  11. Remove lower radiator hose (8286) from radiator. NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
  13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
  14. Support fan shroud, radiator and A/C condenser core (19712) with a suitable jackstand. Remove lower radiator support. Position jackstand aside and carefully remove radiator and fan shroud.
  1. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
  2. Remove upper radiator hose from radiator.
INSTALLATION
  1. Follow removal procedure in reverse order.
  2. Tighten fan shroud bolts and A/C condenser core nuts to radiator to 3-5 Nm (27-44 inch lbs.) .
  3. Tighten lower radiator support bolts to 8-11 Nm (71-97 inch lbs.) .
  4. Tighten transmission oil cooler lines to fittings to 25-28 Nm (18-21 inch lbs.) .
  5. Tighten power steering/transaxle oil cooler and splash shield retaining screws securely.
  6. Refill engine coolant.

Feb 11, 2009 | 1995 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61292 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...