Question about Geo Metro

1 Answer

98 Geo Metro 0300 code

Hi,
I went to Autozone and was told to replace plugs, wires , cap with this code. It did not stop the code. Any ideas?
Joe

Posted by on

  • Joekingiam Aug 26, 2008

    Thanks for the reply except I did not make it clear that the code was cleared already once after repairs, it came back. The problem that is triggering the code is the question.

    Joe

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 182 Answers

You could disconnect the battery.Open the drivers door and wait 5 minutes or so connect the battery with the door still open.This usually resets the computer back to normal and should clear the code.

Posted on Aug 26, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1995 geo metro humid weather starting problems 3 cylinder


Next time it doesn't start, spray your plug wires and distributor cap with WD40. If it fires right up replace your plug wires. I had the same problem with my 3 cyl 1.0L .

Feb 20, 2015 | 1995 Geo Metro

1 Answer

Wont turn over...tries to start...got new starter, plugs , wires, cap.etc.....diagnostic gives me...one flash..then two quick ones..???94 geo metro


The code you refer to is a code that flashes when the diagnostic terminal is grounded with ignition on - eng NOT running If additional codes are stored in the ECM they will appear after this code has flashed three times. See if there are other codes under the conditions I have given and let me know before I give any further advice. Thanks

Dec 06, 2010 | 1994 Geo Metro

1 Answer

Car stalls but starts back up


It had a new cap and rotar and plug wires put on from the people I bought the car from .People told me it started having this problem after they installed the new parts they bought at Autozone so I went and purchased the factory wires ,and dist.cap from a reputable parts store and replaced them and bingo ,no more problem.When buying ignition parts do not go cheap and buy from Autozone.

Mar 14, 2010 | 1994 Geo Prizm

1 Answer

95 geo metro 3cyl. 1.0L no spark changed


Pull one or two sparkplugs and check them for moisture; not fuel, but for water beads.
I don't know how long your engine ran after losing coolant but there is a chance that you lost the head gasket and have gotten water into the cylinders.

Nov 26, 2009 | 1992 Geo Tracker

1 Answer

1991 Geo Metro Automatic/ Sputters, runs rough only in gear.


Could possible be a bad or stuck vaccum advantace mechanism. Check for operation.

Feb 16, 2009 | 1991 Geo Metro

3 Answers

2001 geo metro lsi, engine noise annoying, mostly on acceletation I just bought a 1996 Geo Metro 1 owner, Senior Lady for cheap price. I had just a little bit of gasoline. Since I realized the engine was...


You didn't describe the nature of the 'noise' which is probably why you haven't received a prior reply.
If it is missing, it might be injector problems but the injectors themselves are not loud enough to be heard over the other engine noise.
Spark plugs, ignition wiring, fuel filters cannot 'make noise.' Any of those can cause the car to run rough but not cause any specific noise unless it is related to the engine misfiring and in that case, it wouldn't just be a source of noise but also inadequate acceleration and a prominent jerking of the car at low RPMs. Carbon buildup is the likely cause although causing any engine to lug (drive in a higher gear at low speeds) can damage bearings in the engine, creating excessive bearing play and a knocking noise under some conditions. Also, a failed exhaust manifold gasket or associated pipes being cracked can really cause a racket.
Without us hearing the noise, it's kind of hard to diagnose it, but the above might give you some guidance.     

Sep 26, 2008 | 1996 Geo Metro

1 Answer

1994 Geo Metro Oil in breather


sound like the engine is worn out
do a compression test to start.

Sep 24, 2008 | 1990 Geo Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Mike Gilbreath

Level 1 Expert

50 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...