Question about 1996 Dodge Caravan

1 Answer

How to change oil pressure sensor

I have a 1996 Dodge Caravan 3.3 Litre engine. How do I change out the old oil pressure sensor with a new one. I know where it's located. Is it a repair I can do Myself?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

Yes its on the back of the intake manifold with a two wire pigtail

Posted on Aug 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank sensor on 1996 dodge caravan 2.4L


Hi, the sensor is located on the back side of the engine block, just above the oil pan.
Crawl underneath the engine and look at the back side of the engine block. The crankshaft position sensor is in the center of the block, approximately 10 inches above the oil pan. It is made from black plastic and has a two-wire connector attached to it.

May 11, 2011 | 1996 Dodge Caravan

1 Answer

1996 dodge caravan 2.4 liter 4 cylinders .Engine service light comes on for a period of 2 to 3 months then goes off .Prior to this the engine light stayed on continuously ,until the oxygen sensor connected...


There is some sort of diagnostic code stored in either the ECM(engine computer) or TCM(transmission computer).There are many sensors and solenoids and other data parameters that can cause a codes to set other than just the oxygen sensors.You will need to have the code(s) pulled to know where to start.

May 07, 2011 | 1996 Dodge Caravan

1 Answer

Oil light keeps coming om my 1999 Dodge caravan when it is warmed up and foot is of the gas


Could be low oil level, faulty oil pressure sensor, clogged oil filter, or just plain worn out. Check the level first.

Jan 22, 2011 | 1996 Dodge Caravan

1 Answer

I keep losing oil pressure in my 2004 f150 with a 4.6 litre. I have changed the filter and oil. What is the chance that the oil pump is bad? If so is it located inside the oil pan? Can I change the pump...


Ok 3 questions to answer:

1 yes the pump could be bad, but it is not likely.
2 yes it is in the oil pan.
3 yes you can change it without pulling the engine, though it is not easy.

Most common problem for your oil pressure reading to be going away, is the oil pressure sending unit(sensor) it is located next to the oil filter, check and replace if neccessary this sensor first and see if your oil pressure returns to normal. If not then you may have a pump problem. Hope this helps, let me know.

Jan 25, 2010 | 2004 Ford F150

1 Answer

I have a 1996 dodge caravan my oil lite stays on and dings i have had the oil changed and also changed the oil sending unit. this lite is still on so i thought it might need to be reset the oil lite and...


no reset for that!! check your oil pump pressure with a gauge and insure you have a working oil pump also check the oil filter to make sure the internal check valve isnt stuck! or the filter clogged or worn rod/main bearings

Jan 22, 2010 | 1996 Dodge Caravan

4 Answers

1996 dodge grand caravan transmission will not shift out of 1st gear, speedometer doesn't work either


Mounted on the trany is a speedometer sensor. The vehical will not up-shift it, sensor, is malfunctioning. The vehicles computer doesn't know that it is not going fast enough to change gears.

Dec 08, 2009 | 1996 Dodge Caravan

1 Answer

1996 dodge caravan 3.8 engine stops after 2 or 3 miles will not restart untill cold losing ign fuel pressure 50 PSI


I find the cam position sensor will act like this, but you should have an engine light coming on.

Oct 11, 2009 | 1996 Dodge Caravan

2 Answers

I have a 6 cylinder 1996 Doge Caravan that when it heats up the engine will stall. I had the fuel pump changed and it is brand new - the check engine light is now on. I hear that it may be a sensor - any...


What engine code(s) are you getiing? Try cycling key to, on ,off, on, off, on & leave on. (not start)
now count flashes from check engine light. will be flashes, pause ,flashes for 2 digit #'s. For example: 2 flashes , pause, 2 more is code 22.
3 flashes,pause, 3 more, is code 33. Write them down & get back to us. By the way when you get 55, thats end of message.

Jul 26, 2009 | 1996 Dodge Caravan

1 Answer

1996 Dodge Caravan with 76000 will not shift out of first gear.


is engine light on?may have a faulty input or output speed sensor or solenoid pack..should have trouble codes..if it's 3 speed trans,possible internal problem..need to know if it's 4speed or 3 speed trans

May 09, 2009 | 1996 Dodge Caravan

Not finding what you are looking for?
1996 Dodge Caravan Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...