Question about 2002 Oldsmobile Bravada

1 Answer

A/c compressor 4.2L bravada my a/c compressor stops working once and awhile the clutch will disengauge on its own .

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Oldsmobile Master
  • 61,168 Answers

You most likely have a sticking AC cycling switch, this is located in the low pressure AC line or the accumulator under the hood, it is round and has a wire connector attached.

Posted on Aug 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove fan clutch on 96 bravada


The fan clutch on these models screws on to the water pump via a big nut. If you go to your local auto parts store and ask them for a fan clutch wrench set. They will usually have a loaner program so you wont need to purchase the tool ultimately. Once you have the new clutch ready to be installed, screw it on a couple of turns and then start the engine. The fan clutch will lock right into place. No need to use the wrenches after the removal. I have never had one walk off. Great trick and saves time and energy.

Jul 15, 2011 | 1996 Oldsmobile Bravada

1 Answer

Only speedo & trip odometer works, rest works once in awhile when you hit a bump or thump the dash, any suggestions?


Its got to be an intermittent connection, means taking the dash off and checking all connections are good.

Jun 11, 2011 | 1991 Oldsmobile Bravada

1 Answer

I have an 1985 Bronco 2 with five speed manual transmission, it grinds when I go to shift into reverse with the clutch all the way in but shifting into 1-OD if fine its just reverse??????


The gears 1 and OD, (and any other EXCEPT reverse) have synchronizers that will reduce grinding, for a while...
Your condition sounds like the clutch is not fully disengauging, OR you may not be waiting long enough before attempting to select reverse... Check the clutch adjustment for full disengaugement....Do not let this continue or you will wear out the synchros in the other gears....

Mar 15, 2011 | 1985 Ford Bronco II

1 Answer

I'm wondering whether on my 2003 (B6) S4 4,2l V8 cylinder n. 4 is the fourth one (front to rear) on left bank or the second on the right one. This just to understand the real firing order. Thank...


Firing order for 2003 (B6) Audi S4 4,2l V8 engine is: 1 - 5 - 4 - 8 - 6 - 3 - 7 - 2
Cylinder no.# 1 is first one from right front side of the car, and cylinder no.# 4 is the fourth one (front to rear) on the right bank of cylinder block. See picture below:

tdisline_88.jpg

Dec 08, 2010 | Audi S4 Cars & Trucks

1 Answer

Vehicle will crank over once then seems like starter slips


What do you mean by the starter slips? One common possibility is the starter drive. It is the one way clutch that keeps the runing engine from over spinning the starter and killing it. Near the end of the drive's life, the starter will disengauge early. the cure is pretty easy, replace the starter.

Nov 16, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Need to know how to tell if the compressor clutch is engaging in a 2001 Olds Bravada. It just got recharged and is still blowing warm air.


You will hear the AC compressor clicking on and off if working. If it clicks on and off all the time that tells you that the unit is low on freaon. If it clicks on and stays on the compressor is operating fine

Aug 07, 2010 | 2001 Oldsmobile Bravada

1 Answer

The 4wd light stays on. I have tried pushing the level up and down without success. I also having a problem starting the car (manual gear). I also have a problem while starting the jeep. It is not...


Light will not go out until the gears actually disengauge. Typically there is SOME preload on the gears and that keeps them engauged and light indicates so, correctly. To disengauge, move lever to disengauge and drive in left and right circles. This allows the front drive and rear drive to alter their relation in the transfer case, eventually allowing for release.

Sep 01, 2009 | 2005 Jeep Wrangler

1 Answer

A?C does not work


Ford uses a relay system for the compressor clutch, have someone turn the a/c on while u listen for the relay to click. If you can hear it click check the compressor clutch wire (2 wire plug) to make sure it actually has power. the 6 and 10 series compressors that Ford uses are known to just fail all at once.

Jul 26, 2008 | 1999 Ford Windstar

Not finding what you are looking for?
2002 Oldsmobile Bravada Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...