Question about 2002 Mazda Protege

1 Answer

Oil cooler lines

I need help with the oil cooler lines. i was replacing the radiator on a 2002 mazda protege and i can't remember where the oil cooler lines go connected to.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

The oil cooler lines connect to the tank portion of the radiator there should be one port on top and one port towards the bottom the ports should be no more than 3/8 inches in diameter

Posted on Sep 01, 2008

1 Suggested Answer

SOURCE: oil cooler line

There should be two tranny lines going into the radiator. That means there should be a total of 6 hoses going into the radiator.
Hope it helps.

Posted on Sep 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 GMC Jimmy needs to have the oil cooler lines replaced but I'm confused as to which assembly I need to get the lady at Schucks Oreillys said it's either the lines that go from the transmission to...


The oil lines going to the radiator is your transmission cooler lines, you will look for a smaller radiator and its connections, usually connected using an oil filter adapter.

Dec 13, 2013 | Cars & Trucks

1 Answer

My mazda protege had a leak in the radiator and we were told to put stop leak in it . when i dove off my car started to overheat . I put my heater on to keep the engine a little cooler and this only worke...


If a radiator leaks you buy a new one,common sense

The Stop Leak probably clogged your hearter core
Now you can remove that & try to clean it out or replace
it also

Jun 26, 2011 | 1996 Mazda Protege

1 Answer

1999 Mazda protege has a oily leak just under the radiator what could it be


If the oil you are referring to is pink or red, then it is your transmission fluid. If this is the oil type then I would check the upper and lower tansmissions lines that are routed into your radiator. The purposem of these lines is to cool the transmission fluid. Please see the attached for additional help:

http://www.ehow.com/how_5073604_remove-transmission-cooler-lines.html

Feb 21, 2011 | 2004 Mazda 6

3 Answers

I have oil leaking from gasket or O-ring on oil cooler. Mazda says you have to buy new oil cooler = $400+. Is there a gasket or O-ring replacement available. 2007 Mazda 5 Touring.


on line, auto zone has a o ring for oil cooler at a reasonable cost. if the cooler is contaminated or corroded it needs replaced. if you need one, go online for the best deal. for it cools the oil for the engine. let them know at auto zone, and they should be able to advise you. car dealerships are a big ripoff. a fan blows air on engine oil cooler for disipation off heat. this is important to regulate the tempurature of the oil. have a very good day !!

Jan 20, 2011 | 2006 Mazda 5

1 Answer

A water line to the radiator is broken at the radiator. can it be fixed?


A water line, Is it a hose or a little pipe? Is it for water or oil? Either way, a radiator shop can fix it, they can solder it back together. But I've never seen a water line to the radiator, 2 hoses, and 2 transmission cooler lines at the bottom. Once you get away from the radiator, then you have a dozen water lines running all over the place. Hope this helps.

May 28, 2010 | 2002 Mazda Millenia

1 Answer

My mazda 2002 protege is running hot when ac is on


your car temp is hot because the air-con automatic fan/cooler on the condenser is not functioning. check the electrical connections from the switch as well as from the compressor. otherwise check the thermostat. the fan should run when the aircon is switched on.

Jun 23, 2009 | 1993 Mazda Protege

1 Answer

Radiator replace


I Hope you Find this Helpfull And Please Remember to RATE ME

  1. Drain the coolant.
  2. Disable the SIR.
  3. Move the forwarding discriminating sensor out of the way.
  4. Remove the air cleaner assembly.
  5. Remove the cooling fans.
  6. Disconnect the radiator inlet hose from the radiator.
    1. Disconnect the radiator outlet hose from the radiator.
    2. Disconnect the engine oil cooler lines from the right radiator end tank.
    3. Disconnect the transmission oil cooler lines from the left radiator end tank.
    4. Remove the left and the right engine torque struts.
      1. Remove the upper radiator support screws.
      2. Remove the radiator from the vehicle. Lift the radiator up and out. INSTALLATION PROCEDURE
        1. Install the radiator to the vehicle.
        2. Install the upper radiator support screws. Tighten the bolts to 6 Nm (53 inch lbs.). NOTICE: Refer to Fastener Notice in Service Precautions.
        3. Install the transmission oil cooler lines to the radiator. Tighten the transmission oil cooler line fittings to 27 Nm (20 ft. lbs.).
        4. Connect the engine oil cooler lines to the radiator. Tighten the engine oil cooler lines to 18 Nm (13 ft. lbs.).
        5. Install the left and the right engine support torque struts.Connect the radiator outlet hose to the radiator.
          1. Connect the radiator inlet hose to the radiator.
          2. Install the cooling fans.
          3. Install the air cleaner assembly.
          4. Install the forward discriminating sensor.
          5. Enable the SIR.
          6. Refill the coolant.
        6. Hope this Helps and PLEASE RATE ME

Jun 03, 2009 | 1998 Cadillac DeVille

1 Answer

How to replace the serpentine belt of protege 5 2002, also need the routing diagram


Posted by Asker under 1997 Mazda Protege for their 2002 Mazda Protege 5.
Both are included Below

Click on the following free direct Link. It has the Belt Diagrams for the 1997 Mazda Protege with either the 1.5L DOHC In-Line 4-Cylinder or 1.8L DOHC In-Line 4-Cylinder Engines; along with various engine options (AC/No AC, etc.). Included are Instrucional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/1997/make/mazda/model/protege/1997_mazda_protege_drive_belt_routing_diagram.htm

Click on the following free direct Link. It has the Belt Diagrams for your 2002 Mazda Protege 5 2.0L DOHC In-Line 4-Cylinder Engine; along with various engine options (AC/No AC, etc.). Included are Instructional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/2002/make/mazda/model/protege5/2002_mazda_protege5_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 13, 2009 | 1997 Mazda Protege

1 Answer

My 2000 beetle 2.0 has constant engine oil in the reservoir.


ive seen this problem on a few cheys
turn out it was a cracked head on one and two others the intake gasket was bad

Feb 28, 2009 | 1993 Mazda Protege

2 Answers

Oil cooler line


What's your email address? I'll send you some service manual pdf's.

Aug 24, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...