Question about 1996 Nissan 200SX

1 Answer

Silvia S14 cheers mate will let you no what happens. will get muffler fixed tomorro and let you no if anything changes

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

Sounds great

Posted on Aug 24, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Loud Exhaust

you probably have a small hole before the muffler or a loose clamp. raise the car and visually check the exhaust pipe forward of the muffler for rust or holes or looseness.

May 20, 2014 | 2000 Volkswagen Beetle

2 Answers

1989 celica slow acceleration

Possibly your catalytic converter is clogging up. Short of using a thermometer to check exhaust temp's pre- and post-converter (the temp. after the converter should be about 100 degrees hotter that the temp. before the converter), the next best way is to run car with converter un-hooked and see if that is the problem.
Good luck.

Feb 17, 2012 | 1989 Toyota Celica GT

1 Answer

How do you adjust a s14 silvias handbrake.

on the cable thats attached to the brake

Oct 15, 2009 | 1995 Nissan 200SX

1 Answer

How to fix s14 handbrake

You've got to replace your rear calipers. I say "calipers" because one is hanging up but they should be changed as pairs. Thanks, Dana P.S. It's more likely the calipers than the cables 90% of the time.

Oct 15, 2009 | 1995 Nissan 200SX

2 Answers

When brake pedal pressed side lights come on

hello zeeko1 , over here when that happens its because someone put a single element bulb where a double element bulb goes , now this bulb you take out to fix the problem , look at the bottom of the socket see if it has 1 contact point , then look into the hole where the bulb goes , i bet you see 2 contacts , this single contact bulb is shorting out into the other circuit back feeding voltage to other circuit . cheers mate !

Thanks for using FIX YA !

Jan 28, 2009 | 2004 Land Rover FreeLander

1 Answer

Silvia s14

i dont like to just jump at a expensive thing like that. you should pull the intake side off the turbo and check your impeller endplay and up and down movement first. ill se what i can find for specs. but if it is realy loose then we know what ya have to do

Aug 25, 2008 | 1996 Nissan 200SX

1 Answer

Silvia S14

i think your finding the limit of your turbo for the condition its in. a turbo spins on a small film of oil. that the shaft spins in a tight clearance of a brass bushing and if the turbo becomes out of balance it will fall on its face . this will happen at extreme rpm's and after a while the turbo will star to use oil. that is one of the signs. good luck and never shut down a turbo engine hot it can stick a turbo. if i can help let me know

Aug 24, 2008 | 1996 Nissan 200SX

1 Answer

New manifold

Hi I would just break the tube off, I'm trying to picture the tube, you said it goes exhaust to intake manifolds, its attached from one to the other? To me for what to said about the tube that its some kind of emission device almost like how a turbo works. so I would just disconnect the tube. Which manifold are you replacing? Hope this helps


Aug 23, 2008 | 1996 Nissan 200SX

1 Answer

Changing my 2.6 4 cylinder to a 3.2 v6

to be honest i'm not sure if they fit but the only thing i know is than the wiring is not the same for the electronic fuel injection, you might have to replace the computer or may be part or the whole harness, you better check the wiring diagram firts before trying to go v-6

Jul 19, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
1996 Nissan 200SX Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

68970 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides