Question about 2000 Ford Windstar

1 Answer

Code p1518 i replaced the idle control valve, the code came back, any suggstins what it means?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Posted on Sep 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix fault code P1507


Possible causes
- Faulty Idle Air Control (IAC) valve
- Idle Air Control (IAC) valve harness is open or shorted
- Idle Air Control (IAC) valve circuit poor electrical connection
What does this mean? Tech notes
The P1507 code means that the engine idle is out of factory specification. Sometimes the Idle Air Control (IAC) may have carbon built up. Disconnect the car battery, remove the valve, clean, re-install valve, and drive the vehicle for about 5 minutes with the headlights and A/C ON to get the idle relearned.
If the problem persist, the IAC valve may need to be replaced.

Read more: http://www.engine-codes.com/p1507_ford.html#ixzz3sFPyZe00

Nov 22, 2015 | 2000 Ford Ranger SuperCab

1 Answer

P0304 code and P1518 on 1997 ford escort and car will not start. Should I replace the actauator or get a diagnostic. Both butterfly pieces move by hand when taken off.


i'd have the codes cleared first of all as a stored code does'nt mean the problem is still there , it may have detected a fault with the intake manifold runner control but it may have been a tempory fault but once stored the ecu will think it is still there

Apr 25, 2014 | 1997 Ford Escort

1 Answer

P1518 engine code


P1518 Intake Manifold Runner Control Stuck Open (Bank 1)
Sorry no idea what this means ,but i suspect the valve on the fuel rail the one with the vacumn pipe to it ?'

May 23, 2013 | 2001 Ford Focus

1 Answer

Ford F140 4.2 Do Engine codes P0305, P0306, and P1518 relate to each other


I am assuming you mean F150 truck.
The answer is maybe.
Code 305 and 306 are missfire codes for cylinders 5 and 6.
Code 1518 is for a problem with the intake manifold runner control which could cause the other two codes.

P1518 FORD Description The Intake Manifold Runner Control (IMRC) is monitored for failure during continuous or key ON engine OFF self-test.
Possible causes - Intake Manifold Runner Control (IMRC) harness is open or shorted
- Intake Manifold Runner Control (IMRC) circuit poor electrical connection
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Engine Control Module (ECM)
Read more: http://engine-codes.com/p1518_ford.html#ixzz2KSN6Thui

Feb 10, 2013 | Ford Cars & Trucks

1 Answer

5 ERROR CODES ON A 2002 CHEVY SUBURBAN P0102,P0171,P0174,P0300,P1518 ??????HELP!!!


Change the Mass Air Flow sensor.Or the the Volume Air flow sensor.Also replace the ( IAC ) Idle Air Control. There is no code P1518 are you sure they wrote it down for you correctly? I just had my Library of codes updated last week and it is not on the list. After all repairs are made make sure you have the Diagnostic Trouble Codes Erased from the on board computers memory. This will reset the check engine light and keep it from comming on again for thoes codes.If it does come on again and it relays more DTC you can ask me for further help through the Reply Window. Good Luck and have a good XMASS.

Dec 14, 2010 | 2002 Chevrolet Suburban

1 Answer

My 98 taurus has this codes what do i need to fix? p1518.p0174.p0


p0171 and p0174 are o2 sensors, There are 4 o2 sensors on a Taurus. 1 on each exhaust manifold, and 1 after each catalytic converter.
p1518 is vehicle speed, idle speed control----this means the idle air control needs fixed. you can take it off and clean carbon from it. do not push on end of air valve it will loose its adjustment. do not put in any liquid to clean, the best way is to clean end of valve with an old toothbrush or similar. also clean carbon from engine side where iac mounts. when clean put back on. you can use carb cleaner for end of valve, as for the 02 sensors, you have to find out which ones are bad first. or replace all thats up[ to you. you have to get a 02 sensor socket for 3/8 drive. then they just turn out. the best way to get them out is have the car warm.

Jul 22, 2010 | 1998 Ford Taurus

1 Answer

1999 ford windstar code P1518


This code means the intake manifold runner is stuck open either from a faulty actuator on the intake or the valves plates are gunked up unable to move,

Jun 17, 2010 | 1999 Ford Windstar

1 Answer

2002 F150 v6-4.2L I have a service engine soon ligth on. Install a reader and the code is P1518 manufacturer controlled vehicle speed, Idle control & auxilliary inputs.


YOUR DIFINITION IS INCORRECT, HERE IS THE CODE FROM THE FORD REPAIR MANUAL

P1518 Intake Manifold Runner Control (Stuck Open)
CHECK FOR DISCONNECTED INTAKE RUNNER CONTROL VALVE LINKAGE AT UPPER PLENUM CHAMBER

Oct 09, 2009 | 2002 Ford F150 Regular Cab

1 Answer

Service engine soon light on


you may have a bad intake manifold anti swirl control unit or the vaccum valve, check all connection first and check for vaccunm leaks hope this helps.

Oct 08, 2009 | 2002 Ford F150 Regular Cab

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...