Question about 1992 Mazda 626

1 Answer

Change radiator how do i remove and replace the radiator in a 1992 Mazda 626

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 125 Answers

Its fairly simple. First open pet **** valve on bottom of radiator (if applicable) to drain fluid then remove upper and lower hoses and disconnect and unbolt electric fans, then disconnect water temperature sensor (if applicable) and automatic transmission lines (if applicable) and remove fans with 10 mm socket, then unbolt top radiator bolts with 10 mm socket, simply pull up radiator carefully, you may have to remove part of you air intake system if above radiator if so remove clamp and 10 mm bolts holding it and pull up and away from air intake box after that it should be fairly easy to pull also always check your radiator cap for wear and replace it that may save you alot of money.

Posted on Jan 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Water in mazda 626 won't circulate.

Are you sure you have purged all the air out of the cooling system? That would be the most common issue.

Jun 15, 2016 | 2000 Mazda 626

1 Answer

1992 mazda 626 hesitates on acceleration what's

Sounds like a weak fuel pump.Check your fuel pressure it should be 34-40 with key on engine off.

Jan 25, 2012 | 1992 Mazda 626

1 Answer

Mazda 626 1992 clutch change.

Its a few hour job pulling transmission. Buy a new clutch , pressure plate and throw out bearing or your just looking for doing it again quickly.

Apr 22, 2010 | 1992 Mazda 626

1 Answer

Code 17 on a mazda 626 1992 lx what does it mean

The OBD-1 two digits trouble codes listed 'code-17' as:
Oxygen sensor.

This means that the fuel and ignition systems performance are in need of attention.

1.Distributor Cap: remove the 3-bolts holding the distriboutr to its body.
2. Inspect the distributor cap for cracks, and the roror-button is not worn or broken.
3. Inspect the distributor-cap terminals are not corroded or charred. Replace if charred. Clean them out if corroded.
4. Check the distributor-rotor for cracks or corrosion on its tip, and lesser spring tension.
Replace as necessary.
5. Reverse steps 1-4 to re-install distributor cap. Be sure to remove and replace the plug wires from the old distributor-cap to the new distributor-cap one-by-one. If not, the engine would not run.

1. Undo the top clips holding the fuel-filter hose, and undo the lower clips also.
2. Take out the fuel-filter from its mount.
3. Replace the fuel filter as necessary.(please not the way it was mounted) Reverse removal for installation.

Dec 11, 2009 | 1992 Mazda 626

1 Answer

Where is the water pump mazda 626 1992 GE

Its under the timing belt cover, driven by the timing belt. Replace the timing belt when you replace the pump. While its apart, replace the cam and crank oil seals, and check the bearing for the tensioner, it will need to be replaced also.

Nov 03, 2009 | 1992 Mazda 626

1 Answer

Okay, so now where is the thermostat located? How

The thermostat is in a bubble-type housing at the end of one of the two radiator hoses where they attach to the engine block.

Generally this is a simple job, but sometimes crowded engine components make it difficult to access.


Aug 13, 2009 | 1992 Mazda 626

2 Answers

98 Mazda 626 overheating. Blew off hose and was

it's either a bad thermostat or a leaking head gasket

Aug 13, 2009 | 1992 Mazda 626

1 Answer

Mazda 626 '92 overheats,vibrating, wont accelerate.

reve the car and see if there is an air bobble on top of the radiator, if so change gasket , if not hope full not a cylinder head corrosion.

Jan 12, 2009 | 1992 Mazda 626

1 Answer

Mazda 626 1992 2litre dohc timing case oilseal

there ar two oil seals on your vehicle one is located behind crankshaft pulley and the other is located at rear input shaft to transmission you will need to remove your crankshaft pulleys including pulley boss or transmission and flywheel and torque converter if automatic to change seals are fairly cheap and easy to remove just follow steps in repair manual from local parts store. Or take it to a shop lol.

Oct 19, 2008 | 1992 Mazda 626

Not finding what you are looking for?
1992 Mazda 626 Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides