Question about Ford Ranger

1 Answer

I have a 1999 Ford Ranger and when i engage the four wheel drive in high or low the transfer case engages but the front hubs wont engage

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

Its most likely one hub isnt locking . you need to take the hub apart and clean and inspect for broken parts(some time the hub will get 1/2 engaged and you would put power to it and will break the hub ) make sure your hub isnt broken then reassemble with light grease and try the hub. if broken new are very expensive. there are alot of used one in the salvage yards just give them a call they would love to help you at a fraction of the cost. tech rating 4

Posted on Aug 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1983 ford ranger transfer case engages but the wheel will not engage


you may have lock outs on your wheels these need to be engaged manually

Jul 07, 2012 | 1983 Ford Ranger

2 Answers

Front tires wont engage in four wheel drive


if the actuateor is vacumed,you might have have a hose that came off or it has a split in it somewhere,check that.or if you have posilock hubs one or both may be wore out or lacking grease,they are easy to remove,just a hex wrench and snapring pliers is all you need,remove and inspect for obvious sighns of wear.

Feb 03, 2010 | 1997 Ford Ranger SuperCab

1 Answer

I have a 1996 ford ranger. my 4 wheel drive wont


If your sure it is acually going into gear than check the auto hubs, they go bad alot. also you can with help from a 2nd person jack the truck up all 4wheels put the truck in 4x4 and drive and see if both drive shafts spin if they do its the hubs if the front one doesnt, its the transfer case

Dec 14, 2009 | 1996 Ford F250 Crew Cab

2 Answers

I have a 2000 4wd tacoma with manual locking hubs and the 4wd does not seem to be engaging after locking the hubs and shifting the lever into 4 hi or 4 low


Sounds like one of your hubs is sticking and not engaging. You can check them by engaging the hubs and the transfer case and jacking up each front wheel independently if it doesn't spin your good, if it does you found your problem. As far as fixing a hub goes, it may be just dry and need some grease, or there are some very good aftermarket hubs available from Warn.
Hope this helps

Dec 08, 2009 | 2001 Toyota Tacoma

1 Answer

1988 ford ranger push button four wheel drive an it wont engage all the wires are good it just clicks when u push the button.. what should i look for to make the four wheel drive work again it wont...


Start out with buying yourself a $25 book from the Parts House. The I would go to the front HUBS, secure & safety vehicle before you do anything, Clean, Inspect, Lune & Repair front Hubs as required, get the brakes while you're there. Check your drive line, axles, u-joints etc. Clean , repair , replace as needed. Check for Tranfer case Operation. Is there power going to the front Axle when 4WD is engaged? do you feel a change when you engage the Transfer Case? Have you checked the Power on the circuits? Have you Manual or Auto-locking Front Hubs? Answer all those Questions & read before you do anything.

Nov 03, 2009 | 1988 Ford Ranger

1 Answer

1999 ford ranger 4x4 wont engage


ck frt drive shaft out of trans-fer case is turning if it is ck both hubs on outside of axles auto locking hubs have alot of problems

May 30, 2009 | 1999 Ford Ranger SuperCab

1 Answer

PUSH BUTTON FOUR WHEEL DRIVE FORD RANGER NOT WORKING


the transfer case is sticking from non use, change the lube in the case ( Ford ATF) and drive it for awhile it should be ok then.

Apr 07, 2009 | 1988 Ford Ranger

2 Answers

4x4 wont engage


the motor on the back of the transfer case may be stuck knock on the motor lightly with a hammer when switching the the switch May need a motor

Mar 03, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

1979 ford f-250 four wheel drive won't engage


I take it the transfer case shifter feels okay (shifts through all four gear positions), so try jack up one side of front end, rotate wheel while looking in knuckle to see if drive axle turns, if it does, then hubs engaged. Now if someone holds the front d shaft, and wheel won't turn, then both hubs are engaged. Next put t case in 4xhi or 4xlow, if you cant turn the wheel, then the t case is engaged, and all is normal. If wheel still turns at this point, then the t case is not engaged for some reason, but post again if it does. Hope this helps.

Jan 04, 2009 | 1979 Ford F 350

2 Answers

06 F150 4 four wheel drive wont work


I have a 1994 ford f150, my 4 wheel drive keeps trying to engage by itself even without me touching the automatic hub button....at time you can even hear it engaging and disengaging by itself, the low range light even comes on (dimly)...what could be the cause? the transfer case motor looks good and so does the wiring.

Nov 28, 2008 | 2006 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...