Front windshield washer pump not working, replaced pump but still does not work, when button is pushed in the wipers come on but pump does not hmmm. like usual

Looks like a Body Control Module communication issue.

Windshield Washer
When the washer switch is pulled towards the driver, the SASM sends the washer request to the BCM over the LIN. The BCM activates the windshield wash relay (internal to the BCM) and sends a message to the driver side windshield wiper motor. When the BCM activates the windshield wash relay, voltage is provided to the washer pump, directing washer fluid to the windshield. When the switch is released, the windshield wiper motor continues to activate the windshield wipers for 3 additional wipes and then turns the windshield wipers off.

https://www.justanswer.com/ford/74red-focus-2012-ford-focus-se-need-wiring-diagram-washer-pump.html

..

The washer fuse should have power (battery voltage) while the ignition switch is in the RUN position. Verify both sides of the fuse have power. If the rear wash functions them it's not the fuse.

The switch signals the Body Control Module (BCM). The BCM energizes the front washer relay.

Input to BCM from switch is BCM connector C1,24 PK. Output from BCM to relay is connector C4 15 OG.

You need to verify continuity from the the switch to the BCM and from the BCM to the relay.

Comment below for further assistance.

Replacing parts just to replace them wont fix a bad wire or part. Better to use a voltmeter and ohn meter to check if your getting power to the wires. You may have a bad connection or bad switch on the column for the pumps. Without checking the circuits it will behard to tell what it is thats wrong. Find a wiring diagram and trace the wires and components.

Just replacing parts isn't the way to fix this problem , viewing wiring diagrams too see what all is involved in making the wipers work is . Then using a digital volt ohmmeter to test electrical circuits . Also looking at factory service info. to see how it's suppose to work.
Free wiring diagrams here http://www.bbbind.com/free-tsb/ Enter vehicle info. year , make , model an engine size . Under system click on body & accessories , then under subsystem click on wiper/washer . Click the search button ,then click the blue link. Looking at the wiring diagram i see two fuse's an two relays that are controlled by the BCM - body control module . Also hooking up a scan tool that can read BCM DTC'S - diagnostic trouble codes could be helpful . The wiper switch is a input to the BCM - the BCM will energize the relays to turn on the wipers.

Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper 1 relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIPER/SW 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper 1 relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay contacts to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3715 05: Front Wiper Relay Drive Circuit Short to Battery or Open

One hour plus part.Find should say windshield washer.

you should hear the washer pump working when someone pushes the button. if not you will have to check the pump connector for a bad connection, no power or ground. if this is good then the washer pump will have to be replaced. if you hear the pump running then there may be a blockage in the hose to the nozzle or the nozzle is plugged.

Windshield Washer Pump

1990 Ford Truck F150 1/2 ton P/U 2WD 5.0L FI 8cyl

The Windshield Washer Pump is located: Under hood, driver side front side of wheelwell, mounted inside washer bottle.here's the part. TAAP Windshield Washer Pump 7 664 1990 Ford F150 1 2 ton 2WD 8...

If the pump works, something should be flowing thru the hose to the spray nozzles.
And if the pump works, everything electrical is working.
How do you know the pump works ?

Is your wiper fluid level good?Look for leaks at pump,it's connected to container,also check your hoses leaving pump to windshield,could be loose or binding.

Probably need to replace the pump. Separate pumps for front and rear. Check with a test light to see if there is power to the pump. If it has power but won't work, replace the pump. If no power, you have a wiring issue. Be sure to turn the switch on and have someone push the washer button when you are checking for power. There won't be any until you push it to "wash".