Question about 2003 Dodge Stratus

1 Answer

2003 Dodge Stratus Hazard Light problem

My hazard lights on my Stratus were fine until a few days ago, then they began working sporadically. Now they don't work at all.

I checked the fuse panel inside the car, but none are for the hazard lights. The fuse & relay box under the hood is not labeled. No owner's manual came with the car. I'm looking for one now, but in the meantime, I have to fix this, as my job requires hazard lights.

I should also mention the blinkers aren't working either. Replaced that fuse, with no luck.

I'd appreciate any help!
Thanks!
Misty

Posted by on

  • Anonymous Oct 01, 2008

    HAZARDS AND TURNSIGNALS INOP

  • haypeeps Dec 21, 2008

    I have the same problem, my blinkers and Hazards dont work on my dodge stratus 2002. Help!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same issue with a 2002 stratus, the problem was the flasher relay. It's located inside the steering column, inside the multiswitch, and its fairly easy to replace. Two screws under the steering column to remove the top cover, then two hex screws to remove the multiswitch, then you can remove the relay which is green, mine was part# 04606478AD. You won't find this exact relay at the local auto parts store, but you can order from mopar parts online, or check the parts dept. at your local dealer. I called a local dealer, he didn't have it but was able to find one a few miles away, cost was $30.

Posted on Mar 21, 2012

6 Suggested Answers

maklean
  • 1665 Answers

SOURCE: turn signals /hazard lights don't blink

Hi! check first for any blown fuse. INSPECTION 1. Check for a burnt fusible link with an ohmmeter. 2. If a fusible link burns out, there is a short or some other problem in the circuit. Carefully determine the cause and correct it before replacing the fusible link. The fusible link will burn out within 15 seconds if a higher than specified current flows through the circuit.2f5ff5a.gif

Posted on Jun 03, 2008

awcforever
  • 359 Answers

SOURCE: All my blinkers and brake lights stopped working

PO430: Catalyst System Efficiency Below Threshold (Bank 2)

Here is a site that you should go to and further look at the common problems with your catylitic converter, and also your other emissions systems. Hope it helps, and please rate!!!

http://www.discountconverter.com/catalytic_converters_news/news_page.cfm?Key=codes-po420-po421-po430-po431&News=120

Posted on Mar 15, 2009

  • 150 Answers

SOURCE: blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse

There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

Posted on May 29, 2009

RJones1125
  • 373 Answers

SOURCE: Rapid blinkers and hazard switch

first check all of the bulbs are good. on some cars if a bulb is burned out the blinker will flash faster than normal.

Posted on Nov 02, 2009

swoop611
  • 488 Answers

SOURCE: MY HAZARD LIGHTS WORK BUT MY BLINKERS DONT

Hazard lights are on a different circuit as they are supplied with power from the battery. Indicators are supplied through your ignition switch. Take a look at fuses first, check them electrically using a test probe. Then take a look at the flasher unit. It may be difficult to find but check in the fuse panel first. This usually looks like a square relay type but it will have two or three connections, not four or more. Flasher units dont fail that often but they do fail.Try turning the ignition on and then switch one side flashers on, then tap each relay box in the fuse panel. If it clicks, then that signifys that it is the flasher unit, replace it with the same type. WARNING, if you use the wrong type of flasher unit, you will damage the new unit and pop fuses etc. Make sure you replace it with the same type of flasher unit.

Posted on Feb 08, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My running lights and turning signals do not work , but my break light and head lights work in my 2003 dodge stratus. Checked the fuses and light bulbs and were told they were good.


Do you hear the clickin sound that you usualy hear when using turn signal or hazard lights ?

Have you checked the brake light switch that is licated at the end of the braking pedal arm (folow the metal upwards you'll encouter the switch) (use a mulyi meter on the sund mode to check if there is a closed circuit)

Apr 20, 2015 | Dodge Cars & Trucks

1 Answer

Hazard light switch


Renew the hazard light switch .its faulty

Dec 20, 2013 | 2000 Dodge Stratus

1 Answer

2006 dodge stratus blinkers and emergency light doesnt work. what relay #


Do the lights not come on at all or just not flash? Try left, right signal, stop and hazard, with a few lights out, the flasher will often not operate.

Relays are located in the main panel under the hood.

Hope this helps.

Jan 26, 2011 | 2006 Dodge Stratus

1 Answer

How to locate and replace the flasher in 2001


Sounds as if the hazard flasher is going out. The only problem is that I don't know where it is located. Since yu said that sometimes it works, try it and see if you can find out where the clicking noise is coing from. It should be from somewhere near the steering column. Replace it.

Nov 17, 2009 | 2001 Dodge Stratus

1 Answer

Turn signals and hazards are not working


Look under dash on top of steering column for the hazard relay.

Mar 23, 2009 | 2000 Dodge Stratus

Not finding what you are looking for?
2003 Dodge Stratus Logo

386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

67800 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...