Question about 2003 Kia Sedona

1 Answer

Removing overhead console 03 sedonda w/ homelink

How do i remove the overhead console on my 03 sedona. I have homelink and cant seem to locate any screws.

Posted by on

  • Anonymous Mar 16, 2014

    button stuck

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

There are only two screws to contend with but they are behind the homelink module. To remove the homelink module you're going to use a butter knife. The blade on a butter knife is smooth and if you can find one without any teeth on it, all the better. Stick the knife into the gap between the homelink module and the left side of console housing and pry down on the homelink module. Repeat for the right side and the homelink module should pop out. Once it's out of the way, remove the two screws that hold the console housing to the roof. Now that those screws are removed all that remains is to grab ahold of the front of the console housing (edge toward the windshield) and pull straight down. It can be painful to do this part since you're inserting fingers into a tight space but remember to be gentle. There are two plastic ears on the housing that slide into slots (common trim panel anchors really) and I can see that it could be possible to break them off if one isn't careful.

Hope this helps.

Posted on Sep 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the top center dash storage compartment?


Kia Sedona Car & Truck Interior Consoles & Parts ' eBay

www.ebay.com/sch/Kia-Sedona-Car-Truck...Consoles.../i.html
eBayShop from the world's largest selection and best deals for Kia Sedona Car & Truck ...2002 2003 2004 2005 KIA SEDONA CENTER CONSOLE FOLDING TRAY TAN ....Overhead Console 02-05 Kia Sedona with Map Lights Clock and Storage ...

Center Console Removal - '05 Sedona - Kia Forum

www.kia-forums.com/...sedona.../30338-center-console-removal-05-sed...
Nov 11, 2005 - 5 posts - ‎4 authors I need to remove the center console in my 2005 Sedona so I can remove the stereo. ... address lol) so I have to pull the stereo and probably replace it. .... the right side of the pannel, as well as the hazard switch at the top of the ...

Oct 16, 2015 | 2002 Kia Sedona

1 Answer

Removal of 2002 f350 overhead display?? Much different than exploder


if you are sure there are no screws , its held in place by spring clips . just pull it down carefully and use a panel remover

Feb 28, 2014 | Cars & Trucks

1 Answer

Where is the bleeder screw located for the radiator at on a 03 kia sedona


there is no bleeder screw most vehicles release pressure trough the radiator cap into the coolant reservoir

Dec 07, 2011 | 2003 Kia Sedona

1 Answer

Have a 03 F150 w/moonroof and the compass/temp display has gone out. OEM is not cheap. Any replacement suggestions


It is actually 1 or 2 resistors that have come unsoldered.

If you have a fine point soldering iron, you can repair it. Might want to stop by Radio Shack or the likes and pick up 2 or 3 58 ohm resistors.

Remove the screw from the bottom of the overhead console, and pull down to release the spring clips.

Unscrew the PC Board from the housing, and look at the surface mounted resistors ( they should be marked 580 on them ).

This is what I am talking about on a SuperDuty over head console ( this has 62 ohm resistors / marked 620 )

Missing Surface mounted resistors ( circled in red )
sscullys_13.jpg

Replaced with 62 ohm resistors from radio shack ( covered in tape after taking picture )
sscullys_14.jpg

Pat on F150online.com did a nice write up on this for a F-150 overhead console ( I never got around to taking pictures of a F-150, only the SuperDuty Console ).
Check the Technical Articles / How To forum for a thread titled overhead console repair ( think that is it ).

Nov 11, 2010 | 2003 Ford F150 Regular Cab

1 Answer

How to program overhead console buttos for garage


HomeLink provides the technology for Chrysler and other auto makers. Follow this link and go to page 3. Directions are there...
http://www.eurohomelink.com/PDF-Download/manuals/GB_HomeLink_General_Bedienungsanleitung.pdf

Here is a link to the earliest available Dodge Owner's Manual (2004) which should be a good reference for you in the future...

http://www.dodge.com/en/owners/manuals/index.html?year=1996&nameplate=Ram%20Pickup

Jan 25, 2010 | 2003 Dodge Durango

1 Answer

How do I program the garage door opener in the overhead console of my Kia?


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Dec 21, 2009 | 2003 Kia Sedona

1 Answer

Garage door opener


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Mar 31, 2009 | 2000 Chrysler Town & Country

1 Answer

Can't get lens of interior dome light off to replace bulb.


Yes.
Open up the sunglasses holder and there might be a screw holding it in place there. There is also another screw underneath the main body, just unsnap the cover plate to access it.

The entire console slide back away from the windshield about 1/2" once the screws are removed, then drops away.

Mar 22, 2009 | 2002 Dodge Dakota Club Cab

3 Answers

2003 Sahara Landcruiser Console removal


Dear Sir/Madam,

Just got done doing it actually. remove all the visible screws.. two in the front two above the cup holders. 4 Screws total there. Next pull off the black part that has the cup holders. Under that there are 2 screws holding the console to the floor. Remove them. Then go to the sides on the back.. There are two covers they are oval shaped. pop them off and remove the 4 bolts in there. Then pull off the top part. Next pull out the whole console. The only part thats left it the metal support. It will have 4 bolts and 4 screws attaching it to the floor. Then your done. Except for the two ugly holes where there is no carpet.

Go to this link and follow the 7 steps to fix your problem.....

http://www.ehow.com/how_2092450_replace-car-console.html

Thanks
good luck



Aug 07, 2008 | 2003 Toyota Land Cruiser

1 Answer

Jag xj6 1996 97 programming the garage door openers


1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.) 2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface (located on your visor), keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)
property_damage_symbol_sm.gif Note: Some garage door openers may require you to replace step 3 with the “cycling” procedure noted in the “View Canadian Instructions” section.
4. Press and hold the trained HomeLink button and observe the indicator light.
  • If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
  • If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.
5. At the garage door opener receiver (motorhead unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener’s manual or contact us. 6. Press and release the “learn” or “smart” button (the name and color of the button may vary by manufacturer). NOTE: Once the button is pressed, there are 30 seconds in which to initiate the next step. 7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the “press/hold/release” sequence up to 3 times to complete the training process.

Jun 13, 2008 | 1997 Jaguar XJ6

Not finding what you are looking for?
2003 Kia Sedona Logo

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...